Moe's MS-104 User manual

Global international operation Whenever & Wherever
You are, All-in-one Mobile App
Anywhere
APP
APP
Schedule timer Voice control-work
with Google Home Voice control-work with Amazon Alexa Device Sharing
App
APP
Router Voice control
Inhouse local operation
INSTALLATION
Warnings:
1. Installation must be carried out by a qualified
electrician in accordance with local regulations.
2. Keep the device out of the reach of children.
3. Keep the device away from water, damp or hot
environment.
4. Install the device away from strong signal sources
such as microwave oven that may cause signal
interruption resulted in abnormal operation of the
device.
5. Obstruction by concrete wall or metallic materials
may reduce the effective operation range of the
device and should be avoided.
6. Do NOT attempt to disassemble, repair or modify
the device.
Remove the old switch
Step 2
Step 3
Remove the switch and pull it away from the wall.
Identify Line/Load Wire(Note:The color of your wire
may be different from the color shown on the
manual.)
We recommend you remove the faceplate from the old switch and
use an electrical tester to test all wires connected to the switch to
ensure there is no voltage in the circuit.
You may need to turn off more than one circuit breaker.
Verify power is off
TECHNICAL SPECIFICATIONS
1 2 3 4
5 6 7 8
Push wall switch
(Reset switch)
Rocker light switch
1. With one 2 Gang switch
WIRING DIAGRAM
Enjoy Our SmartLife
EnglishEnglish English
EnglishEnglish EnglishEnglish
English
Smart Switch Module
Instruction Manual
MS-104
Step 1
Please disconnect the power supply before installing
or removing the device for avoiding irreversible
damage on the device from the electric current or
some unpredictable problems such as lamp flashing.
Attention:
Turn off the circuit breaker and use the electrical tester to
test the power.
Ensure the circuit breaker is off before wiring.
Rocker light switch
Push wall switch
(Reset switch)
请扫描二维码获取中文说明书、安装视频及功能介绍
Bitte scannen Sie den QR-Code, um das deutsche
Handbuch, das Installationsvideo und die Funktionsein-
führung zu erhalten
Escanee el código QR para obtener el manual en
español, el video de instalación y la introducción de la
función
Veuillez scanner le code QR pour obtenir le manuel en
français, la vidéo d'installation et l'introduction des
fonctions
Отсканируйте QR-код, чтобы получить руководство на
русском языке, видео по установке и описание
функций
Leia o código QR para obter o manual em português, o
vídeo de instalação e a introdução das funções
47 mm
22.5 mm
52 mm
L
LN
S1
1
L N
2. With 2 Gang 2 Way switches
L N
MS-104
Wireless Protocol
Wi-Fi 2.4GHz IEEE 802.11b/g/n
Operation Temp. -10ºC - +40ºC
Case Temp
Dims (WxDxH)
IP Rating IP20
90-250V AC 50/60Hz
Current 10A
47 x 52 x 22.5 mm
Tc: +80ºC (Max.)
Model
Voltage

Global international operation Whenever & Wherever
You are, All-in-one Mobile App
Anywhere
APP
APP
Schedule timer Voice control-work
with Google Home Voice control-work with Amazon Alexa Device Sharing
App
APP
Router Voice control
Inhouse local operation
INSTALLATION
Warnings:
1. Installation must be carried out by a qualified
electrician in accordance with local regulations.
2. Keep the device out of the reach of children.
3. Keep the device away from water, damp or hot
environment.
4. Install the device away from strong signal sources
such as microwave oven that may cause signal
interruption resulted in abnormal operation of the
device.
5. Obstruction by concrete wall or metallic materials
may reduce the effective operation range of the
device and should be avoided.
6. Do NOT attempt to disassemble, repair or modify
the device.
Remove the old switch
Step 2
Step 3
Remove the switch and pull it away from the wall.
Identify Line/Load Wire(Note:The color of your wire
may be different from the color shown on the
manual.)
We recommend you remove the faceplate from the old switch and
use an electrical tester to test all wires connected to the switch to
ensure there is no voltage in the circuit.
You may need to turn off more than one circuit breaker.
Verify power is off
TECHNICAL SPECIFICATIONS
1 2 3 4
5 6 7 8
Push wall switch
(Reset switch)
Rocker light switch
1. With one 2 Gang switch
WIRING DIAGRAM
Enjoy Our SmartLife
EnglishEnglish English
EnglishEnglish EnglishEnglish
English
Smart Switch Module
Instruction Manual
MS-104
Step 1
Please disconnect the power supply before installing
or removing the device for avoiding irreversible
damage on the device from the electric current or
some unpredictable problems such as lamp flashing.
Attention:
Turn off the circuit breaker and use the electrical tester to
test the power.
Ensure the circuit breaker is off before wiring.
Rocker light switch
Push wall switch
(Reset switch)
请扫描二维码获取中文说明书、安装视频及功能介绍
Bitte scannen Sie den QR-Code, um das deutsche
Handbuch, das Installationsvideo und die Funktionsein-
führung zu erhalten
Escanee el código QR para obtener el manual en
español, el video de instalación y la introducción de la
función
Veuillez scanner le code QR pour obtenir le manuel en
français, la vidéo d'installation et l'introduction des
fonctions
Отсканируйте QR-код, чтобы получить руководство на
русском языке, видео по установке и описание
функций
Leia o código QR para obter o manual em português, o
vídeo de instalação e a introdução das funções
47 mm
22.5 mm
52 mm
L
LN
S1
1
L N
2. With 2 Gang 2 Way switches
L N
MS-104
Wireless Protocol
Wi-Fi 2.4GHz IEEE 802.11b/g/n
Operation Temp. -10ºC - +40ºC
Case Temp
Dims (WxDxH)
IP Rating IP20
90-250V AC 50/60Hz
Current 10A
47 x 52 x 22.5 mm
Tc: +80ºC (Max.)
Model
Voltage

Global international operation Whenever & Wherever
You are, All-in-one Mobile App
Anywhere
APP
APP
Schedule timer Voice control-work
with Google Home Voice control-work with Amazon Alexa Device Sharing
App
APP
Router Voice control
Inhouse local operation
INSTALLATION
Warnings:
1. Installation must be carried out by a qualified
electrician in accordance with local regulations.
2. Keep the device out of the reach of children.
3. Keep the device away from water, damp or hot
environment.
4. Install the device away from strong signal sources
such as microwave oven that may cause signal
interruption resulted in abnormal operation of the
device.
5. Obstruction by concrete wall or metallic materials
may reduce the effective operation range of the
device and should be avoided.
6. Do NOT attempt to disassemble, repair or modify
the device.
Remove the old switch
Step 2
Step 3
Remove the switch and pull it away from the wall.
Identify Line/Load Wire(Note:The color of your wire
may be different from the color shown on the
manual.)
We recommend you remove the faceplate from the old switch and
use an electrical tester to test all wires connected to the switch to
ensure there is no voltage in the circuit.
You may need to turn off more than one circuit breaker.
Verify power is off
TECHNICAL SPECIFICATIONS
1 2 3 4
5 6 7 8
Push wall switch
(Reset switch)
Rocker light switch
1. With one 2 Gang switch
WIRING DIAGRAM
Enjoy Our SmartLife
EnglishEnglish English
EnglishEnglish EnglishEnglish
English
Smart Switch Module
Instruction Manual
MS-104
Step 1
Please disconnect the power supply before installing
or removing the device for avoiding irreversible
damage on the device from the electric current or
some unpredictable problems such as lamp flashing.
Attention:
Turn off the circuit breaker and use the electrical tester to
test the power.
Ensure the circuit breaker is off before wiring.
Rocker light switch
Push wall switch
(Reset switch)
请扫描二维码获取中文说明书、安装视频及功能介绍
Bitte scannen Sie den QR-Code, um das deutsche
Handbuch, das Installationsvideo und die Funktionsein-
führung zu erhalten
Escanee el código QR para obtener el manual en
español, el video de instalación y la introducción de la
función
Veuillez scanner le code QR pour obtenir le manuel en
français, la vidéo d'installation et l'introduction des
fonctions
Отсканируйте QR-код, чтобы получить руководство на
русском языке, видео по установке и описание
функций
Leia o código QR para obter o manual em português, o
vídeo de instalação e a introdução das funções
47 mm
22.5 mm
52 mm
L
LN
S1
1
L N
2. With 2 Gang 2 Way switches
L N
MS-104
Wireless Protocol
Wi-Fi 2.4GHz IEEE 802.11b/g/n
Operation Temp. -10ºC - +40ºC
Case Temp
Dims (WxDxH)
IP Rating IP20
90-250V AC 50/60Hz
Current 10A
47 x 52 x 22.5 mm
Tc: +80ºC (Max.)
Model
Voltage

Global international operation Whenever & Wherever
You are, All-in-one Mobile App
Anywhere
APP
APP
Schedule timer Voice control-work
with Google Home Voice control-work with Amazon Alexa Device Sharing
App
APP
Router Voice control
Inhouse local operation
INSTALLATION
Warnings:
1. Installation must be carried out by a qualified
electrician in accordance with local regulations.
2. Keep the device out of the reach of children.
3. Keep the device away from water, damp or hot
environment.
4. Install the device away from strong signal sources
such as microwave oven that may cause signal
interruption resulted in abnormal operation of the
device.
5. Obstruction by concrete wall or metallic materials
may reduce the effective operation range of the
device and should be avoided.
6. Do NOT attempt to disassemble, repair or modify
the device.
Remove the old switch
Step 2
Step 3
Remove the switch and pull it away from the wall.
Identify Line/Load Wire(Note:The color of your wire
may be different from the color shown on the
manual.)
We recommend you remove the faceplate from the old switch and
use an electrical tester to test all wires connected to the switch to
ensure there is no voltage in the circuit.
You may need to turn off more than one circuit breaker.
Verify power is off
TECHNICAL SPECIFICATIONS
1 2 3 4
5 6 7 8
Push wall switch
(Reset switch)
Rocker light switch
1. With one 2 Gang switch
WIRING DIAGRAM
Enjoy Our SmartLife
EnglishEnglish English
EnglishEnglish EnglishEnglish
English
Smart Switch Module
Instruction Manual
MS-104
Step 1
Please disconnect the power supply before installing
or removing the device for avoiding irreversible
damage on the device from the electric current or
some unpredictable problems such as lamp flashing.
Attention:
Turn off the circuit breaker and use the electrical tester to
test the power.
Ensure the circuit breaker is off before wiring.
Rocker light switch
Push wall switch
(Reset switch)
请扫描二维码获取中文说明书、安装视频及功能介绍
Bitte scannen Sie den QR-Code, um das deutsche
Handbuch, das Installationsvideo und die Funktionsein-
führung zu erhalten
Escanee el código QR para obtener el manual en
español, el video de instalación y la introducción de la
función
Veuillez scanner le code QR pour obtenir le manuel en
français, la vidéo d'installation et l'introduction des
fonctions
Отсканируйте QR-код, чтобы получить руководство на
русском языке, видео по установке и описание
функций
Leia o código QR para obter o manual em português, o
vídeo de instalação e a introdução das funções
47 mm
22.5 mm
52 mm
L
LN
S1
1
L N
2. With 2 Gang 2 Way switches
L N
MS-104
Wireless Protocol
Wi-Fi 2.4GHz IEEE 802.11b/g/n
Operation Temp. -10ºC - +40ºC
Case Temp
Dims (WxDxH)
IP Rating IP20
90-250V AC 50/60Hz
Current 10A
47 x 52 x 22.5 mm
Tc: +80ºC (Max.)
Model
Voltage

Global international operation Whenever & Wherever
You are, All-in-one Mobile App
Anywhere
APP
APP
Schedule timer Voice control-work
with Google Home Voice control-work with Amazon Alexa Device Sharing
App
APP
Router Voice control
Inhouse local operation
INSTALLATION
Warnings:
1. Installation must be carried out by a qualified
electrician in accordance with local regulations.
2. Keep the device out of the reach of children.
3. Keep the device away from water, damp or hot
environment.
4. Install the device away from strong signal sources
such as microwave oven that may cause signal
interruption resulted in abnormal operation of the
device.
5. Obstruction by concrete wall or metallic materials
may reduce the effective operation range of the
device and should be avoided.
6. Do NOT attempt to disassemble, repair or modify
the device.
Remove the old switch
Step 2
Step 3
Remove the switch and pull it away from the wall.
Identify Line/Load Wire(Note:The color of your wire
may be different from the color shown on the
manual.)
We recommend you remove the faceplate from the old switch and
use an electrical tester to test all wires connected to the switch to
ensure there is no voltage in the circuit.
You may need to turn off more than one circuit breaker.
Verify power is off
TECHNICAL SPECIFICATIONS
1 2 3 4
5 6 7 8
Push wall switch
(Reset switch)
Rocker light switch
1. With one 2 Gang switch
WIRING DIAGRAM
Enjoy Our SmartLife
EnglishEnglish English
EnglishEnglish EnglishEnglish
English
Smart Switch Module
Instruction Manual
MS-104
Step 1
Please disconnect the power supply before installing
or removing the device for avoiding irreversible
damage on the device from the electric current or
some unpredictable problems such as lamp flashing.
Attention:
Turn off the circuit breaker and use the electrical tester to
test the power.
Ensure the circuit breaker is off before wiring.
Rocker light switch
Push wall switch
(Reset switch)
请扫描二维码获取中文说明书、安装视频及功能介绍
Bitte scannen Sie den QR-Code, um das deutsche
Handbuch, das Installationsvideo und die Funktionsein-
führung zu erhalten
Escanee el código QR para obtener el manual en
español, el video de instalación y la introducción de la
función
Veuillez scanner le code QR pour obtenir le manuel en
français, la vidéo d'installation et l'introduction des
fonctions
Отсканируйте QR-код, чтобы получить руководство на
русском языке, видео по установке и описание
функций
Leia o código QR para obter o manual em português, o
vídeo de instalação e a introdução das funções
47 mm
22.5 mm
52 mm
L
LN
S1
1
L N
2. With 2 Gang 2 Way switches
L N
MS-104
Wireless Protocol
Wi-Fi 2.4GHz IEEE 802.11b/g/n
Operation Temp. -10ºC - +40ºC
Case Temp
Dims (WxDxH)
IP Rating IP20
90-250V AC 50/60Hz
Current 10A
47 x 52 x 22.5 mm
Tc: +80ºC (Max.)
Model
Voltage

Global international operation Whenever & Wherever
You are, All-in-one Mobile App
Anywhere
APP
APP
Schedule timer Voice control-work
with Google Home Voice control-work with Amazon Alexa Device Sharing
App
APP
Router Voice control
Inhouse local operation
INSTALLATION
Warnings:
1. Installation must be carried out by a qualified
electrician in accordance with local regulations.
2. Keep the device out of the reach of children.
3. Keep the device away from water, damp or hot
environment.
4. Install the device away from strong signal sources
such as microwave oven that may cause signal
interruption resulted in abnormal operation of the
device.
5. Obstruction by concrete wall or metallic materials
may reduce the effective operation range of the
device and should be avoided.
6. Do NOT attempt to disassemble, repair or modify
the device.
Remove the old switch
Step 2
Step 3
Remove the switch and pull it away from the wall.
Identify Line/Load Wire(Note:The color of your wire
may be different from the color shown on the
manual.)
We recommend you remove the faceplate from the old switch and
use an electrical tester to test all wires connected to the switch to
ensure there is no voltage in the circuit.
You may need to turn off more than one circuit breaker.
Verify power is off
TECHNICAL SPECIFICATIONS
1 2 3 4
5 6 7 8
Push wall switch
(Reset switch)
Rocker light switch
1. With one 2 Gang switch
WIRING DIAGRAM
Enjoy Our SmartLife
EnglishEnglish English
EnglishEnglish EnglishEnglish
English
Smart Switch Module
Instruction Manual
MS-104
Step 1
Please disconnect the power supply before installing
or removing the device for avoiding irreversible
damage on the device from the electric current or
some unpredictable problems such as lamp flashing.
Attention:
Turn off the circuit breaker and use the electrical tester to
test the power.
Ensure the circuit breaker is off before wiring.
Rocker light switch
Push wall switch
(Reset switch)
请扫描二维码获取中文说明书、安装视频及功能介绍
Bitte scannen Sie den QR-Code, um das deutsche
Handbuch, das Installationsvideo und die Funktionsein-
führung zu erhalten
Escanee el código QR para obtener el manual en
español, el video de instalación y la introducción de la
función
Veuillez scanner le code QR pour obtenir le manuel en
français, la vidéo d'installation et l'introduction des
fonctions
Отсканируйте QR-код, чтобы получить руководство на
русском языке, видео по установке и описание
функций
Leia o código QR para obter o manual em português, o
vídeo de instalação e a introdução das funções
47 mm
22.5 mm
52 mm
L
LN
S1
1
L N
2. With 2 Gang 2 Way switches
L N
MS-104
Wireless Protocol
Wi-Fi 2.4GHz IEEE 802.11b/g/n
Operation Temp. -10ºC - +40ºC
Case Temp
Dims (WxDxH)
IP Rating IP20
90-250V AC 50/60Hz
Current 10A
47 x 52 x 22.5 mm
Tc: +80ºC (Max.)
Model
Voltage

Global international operation Whenever & Wherever
You are, All-in-one Mobile App
Anywhere
APP
APP
Schedule timer Voice control-work
with Google Home Voice control-work with Amazon Alexa Device Sharing
App
APP
Router Voice control
Inhouse local operation
INSTALLATION
Warnings:
1. Installation must be carried out by a qualified
electrician in accordance with local regulations.
2. Keep the device out of the reach of children.
3. Keep the device away from water, damp or hot
environment.
4. Install the device away from strong signal sources
such as microwave oven that may cause signal
interruption resulted in abnormal operation of the
device.
5. Obstruction by concrete wall or metallic materials
may reduce the effective operation range of the
device and should be avoided.
6. Do NOT attempt to disassemble, repair or modify
the device.
Remove the old switch
Step 2
Step 3
Remove the switch and pull it away from the wall.
Identify Line/Load Wire(Note:The color of your wire
may be different from the color shown on the
manual.)
We recommend you remove the faceplate from the old switch and
use an electrical tester to test all wires connected to the switch to
ensure there is no voltage in the circuit.
You may need to turn off more than one circuit breaker.
Verify power is off
TECHNICAL SPECIFICATIONS
1 2 3 4
5 6 7 8
Push wall switch
(Reset switch)
Rocker light switch
1. With one 2 Gang switch
WIRING DIAGRAM
Enjoy Our SmartLife
EnglishEnglish English
EnglishEnglish EnglishEnglish
English
Smart Switch Module
Instruction Manual
MS-104
Step 1
Please disconnect the power supply before installing
or removing the device for avoiding irreversible
damage on the device from the electric current or
some unpredictable problems such as lamp flashing.
Attention:
Turn off the circuit breaker and use the electrical tester to
test the power.
Ensure the circuit breaker is off before wiring.
Rocker light switch
Push wall switch
(Reset switch)
请扫描二维码获取中文说明书、安装视频及功能介绍
Bitte scannen Sie den QR-Code, um das deutsche
Handbuch, das Installationsvideo und die Funktionsein-
führung zu erhalten
Escanee el código QR para obtener el manual en
español, el video de instalación y la introducción de la
función
Veuillez scanner le code QR pour obtenir le manuel en
français, la vidéo d'installation et l'introduction des
fonctions
Отсканируйте QR-код, чтобы получить руководство на
русском языке, видео по установке и описание
функций
Leia o código QR para obter o manual em português, o
vídeo de instalação e a introdução das funções
47 mm
22.5 mm
52 mm
L
LN
S1
1
L N
2. With 2 Gang 2 Way switches
L N
MS-104
Wireless Protocol
Wi-Fi 2.4GHz IEEE 802.11b/g/n
Operation Temp. -10ºC - +40ºC
Case Temp
Dims (WxDxH)
IP Rating IP20
90-250V AC 50/60Hz
Current 10A
47 x 52 x 22.5 mm
Tc: +80ºC (Max.)
Model
Voltage

Global international operation Whenever & Wherever
You are, All-in-one Mobile App
Anywhere
APP
APP
Schedule timer Voice control-work
with Google Home Voice control-work with Amazon Alexa Device Sharing
App
APP
Router Voice control
Inhouse local operation
INSTALLATION
Warnings:
1. Installation must be carried out by a qualified
electrician in accordance with local regulations.
2. Keep the device out of the reach of children.
3. Keep the device away from water, damp or hot
environment.
4. Install the device away from strong signal sources
such as microwave oven that may cause signal
interruption resulted in abnormal operation of the
device.
5. Obstruction by concrete wall or metallic materials
may reduce the effective operation range of the
device and should be avoided.
6. Do NOT attempt to disassemble, repair or modify
the device.
Remove the old switch
Step 2
Step 3
Remove the switch and pull it away from the wall.
Identify Line/Load Wire(Note:The color of your wire
may be different from the color shown on the
manual.)
We recommend you remove the faceplate from the old switch and
use an electrical tester to test all wires connected to the switch to
ensure there is no voltage in the circuit.
You may need to turn off more than one circuit breaker.
Verify power is off
TECHNICAL SPECIFICATIONS
1 2 3 4
5 6 7 8
Push wall switch
(Reset switch)
Rocker light switch
1. With one 2 Gang switch
WIRING DIAGRAM
Enjoy Our SmartLife
EnglishEnglish English
EnglishEnglish EnglishEnglish
English
Smart Switch Module
Instruction Manual
MS-104
Step 1
Please disconnect the power supply before installing
or removing the device for avoiding irreversible
damage on the device from the electric current or
some unpredictable problems such as lamp flashing.
Attention:
Turn off the circuit breaker and use the electrical tester to
test the power.
Ensure the circuit breaker is off before wiring.
Rocker light switch
Push wall switch
(Reset switch)
请扫描二维码获取中文说明书、安装视频及功能介绍
Bitte scannen Sie den QR-Code, um das deutsche
Handbuch, das Installationsvideo und die Funktionsein-
führung zu erhalten
Escanee el código QR para obtener el manual en
español, el video de instalación y la introducción de la
función
Veuillez scanner le code QR pour obtenir le manuel en
français, la vidéo d'installation et l'introduction des
fonctions
Отсканируйте QR-код, чтобы получить руководство на
русском языке, видео по установке и описание
функций
Leia o código QR para obter o manual em português, o
vídeo de instalação e a introdução das funções
47 mm
22.5 mm
52 mm
L
LN
S1
1
L N
2. With 2 Gang 2 Way switches
L N
MS-104
Wireless Protocol
Wi-Fi 2.4GHz IEEE 802.11b/g/n
Operation Temp. -10ºC - +40ºC
Case Temp
Dims (WxDxH)
IP Rating IP20
90-250V AC 50/60Hz
Current 10A
47 x 52 x 22.5 mm
Tc: +80ºC (Max.)
Model
Voltage

How to reset/re-pair WiFi code
Note:
FAQ
Q1: What should I do if I can’t configure the switch module?
a. Please check whether device is powered on.
b. Make sure your mobile and switch module are under the
same 2.4 GHz WiFi network.
c. Whether it’s in good internet conditions.
d. Make sure the password entered in App is correct.
e. Make sure the wiring is correct.
Q2: What device can be connected to this WiFi switch
module?
Q3: What happens if the WiFi goes off?
Most of your household electrical appliances can be, such as
lamps, laundry machine, coffe maker, etc.
You can still control the device connected the switch module
with your traditional switch and once WiFi is active again the
device connected to module will connect automatically to your
WiFi network.
Q4: What should I do if I change the WiFi network or
change the password?
You have to re-connect our WiFi switch module to the
new WiFi network according to the App User Manual.
9 10 11 12
14
13 15 16
b. For reset switch (Set as reset switch in APP) :
press the switch button for 10 times to hear the
beep sounds continuously.
(If using rocker light switch，you should press the
rocker light switch for 20 times)
c. For rocker light switch (Set as rocker switch in
APP)
: press the switch button for 10 times(ON/OFF
cycle for 5 times) to hear the beep sounds
continuously.
(If using reset switch，you should press the reset
switch for 5 times)
a. For reset button
: long press the button on the
module to hear the beep sounds continuously.
Wi-Fi link method:(three pairing methods)
Complete the wiring of the switch module before pairing
This WiFi switch module fits for rocker light
switch and reset switch meanwhile.Please pay
attention to the different pairing modes.
Wiring Instructions and Diagrams
1.Turn off the power supply before carrying out any
electrical installation work.
Notes: Put your smartphone close to the switch
sure you have min. 50% Wi-Fi signal.
module when you’re configuring, and make
EnglishEnglish EnglishEnglish
EnglishEnglish EnglishEnglish
3. With Wall Socket
L N
Wall Socket
2.Connect wires according to the wiring diagram.
3.Insert the module into the junction box.
4.Connect the power supply and follow switch module
configuration instructions.
Reset button
Rocker switch Push wall switch
(Reset switch)
Fit for the two switches
Note:
3
2
Registration or Log in
Download “Smart Life”Application
Enter the Register/Login interface;tap
“Register” to create an account by entering
your phone number to get verification code
and “Set password”.Choose “Log in” if you
already have a Smart Life account.
Configure the APP to the switch
Preparation: Ensure the switch has been
connected with electricity;ensure your phone has
been connected to Wi-Fi and is able to connect
to the Internet.
Download Smart Life App
Please scan the QR code or download Smart
Life on App store.
Add Devices
1
3.1 Method one:
Scan the QR code to configure the network guide.
⑴ ⑵
Scan the QR code Please connect the device
according to the
configuration process.
2.Open Smart Life/Tuya App and Click“+”,then
the prompt page will automatically show on the
screen.Click “Add”.
3.2 Method two :
Pair and clear up the WiFi code withBluetooth and
WiFi connected meantime.(New Updated)
1.Confirm the device beeps continuously, if not,
please refer to page 14 for how to enter the
network configuration.
WiFi Smart Switch
3.Select the device you want to add and click “+”

How to reset/re-pair WiFi code
Note:
FAQ
Q1: What should I do if I can’t configure the switch module?
a. Please check whether device is powered on.
b. Make sure your mobile and switch module are under the
same 2.4 GHz WiFi network.
c. Whether it’s in good internet conditions.
d. Make sure the password entered in App is correct.
e. Make sure the wiring is correct.
Q2: What device can be connected to this WiFi switch
module?
Q3: What happens if the WiFi goes off?
Most of your household electrical appliances can be, such as
lamps, laundry machine, coffe maker, etc.
You can still control the device connected the switch module
with your traditional switch and once WiFi is active again the
device connected to module will connect automatically to your
WiFi network.
Q4: What should I do if I change the WiFi network or
change the password?
You have to re-connect our WiFi switch module to the
new WiFi network according to the App User Manual.
9 10 11 12
14
13 15 16
b. For reset switch (Set as reset switch in APP) :
press the switch button for 10 times to hear the
beep sounds continuously.
(If using rocker light switch，you should press the
rocker light switch for 20 times)
c. For rocker light switch (Set as rocker switch in
APP)
: press the switch button for 10 times(ON/OFF
cycle for 5 times) to hear the beep sounds
continuously.
(If using reset switch，you should press the reset
switch for 5 times)
a. For reset button
: long press the button on the
module to hear the beep sounds continuously.
Wi-Fi link method:(three pairing methods)
Complete the wiring of the switch module before pairing
This WiFi switch module fits for rocker light
switch and reset switch meanwhile.Please pay
attention to the different pairing modes.
Wiring Instructions and Diagrams
1.Turn off the power supply before carrying out any
electrical installation work.
Notes: Put your smartphone close to the switch
sure you have min. 50% Wi-Fi signal.
module when you’re configuring, and make
EnglishEnglish EnglishEnglish
EnglishEnglish EnglishEnglish
3. With Wall Socket
L N
Wall Socket
2.Connect wires according to the wiring diagram.
3.Insert the module into the junction box.
4.Connect the power supply and follow switch module
configuration instructions.
Reset button
Rocker switch Push wall switch
(Reset switch)
Fit for the two switches
Note:
3
2
Registration or Log in
Download “Smart Life”Application
Enter the Register/Login interface;tap
“Register” to create an account by entering
your phone number to get verification code
and “Set password”.Choose “Log in” if you
already have a Smart Life account.
Configure the APP to the switch
Preparation: Ensure the switch has been
connected with electricity;ensure your phone has
been connected to Wi-Fi and is able to connect
to the Internet.
Download Smart Life App
Please scan the QR code or download Smart
Life on App store.
Add Devices
1
3.1 Method one:
Scan the QR code to configure the network guide.
⑴ ⑵
Scan the QR code Please connect the device
according to the
configuration process.
2.Open Smart Life/Tuya App and Click“+”,then
the prompt page will automatically show on the
screen.Click “Add”.
3.2 Method two :
Pair and clear up the WiFi code withBluetooth and
WiFi connected meantime.(New Updated)
1.Confirm the device beeps continuously, if not,
please refer to page 14 for how to enter the
network configuration.
WiFi Smart Switch
3.Select the device you want to add and click “+”

How to reset/re-pair WiFi code
Note:
FAQ
Q1: What should I do if I can’t configure the switch module?
a. Please check whether device is powered on.
b. Make sure your mobile and switch module are under the
same 2.4 GHz WiFi network.
c. Whether it’s in good internet conditions.
d. Make sure the password entered in App is correct.
e. Make sure the wiring is correct.
Q2: What device can be connected to this WiFi switch
module?
Q3: What happens if the WiFi goes off?
Most of your household electrical appliances can be, such as
lamps, laundry machine, coffe maker, etc.
You can still control the device connected the switch module
with your traditional switch and once WiFi is active again the
device connected to module will connect automatically to your
WiFi network.
Q4: What should I do if I change the WiFi network or
change the password?
You have to re-connect our WiFi switch module to the
new WiFi network according to the App User Manual.
9 10 11 12
14
13 15 16
b. For reset switch (Set as reset switch in APP) :
press the switch button for 10 times to hear the
beep sounds continuously.
(If using rocker light switch，you should press the
rocker light switch for 20 times)
c. For rocker light switch (Set as rocker switch in
APP)
: press the switch button for 10 times(ON/OFF
cycle for 5 times) to hear the beep sounds
continuously.
(If using reset switch，you should press the reset
switch for 5 times)
a. For reset button
: long press the button on the
module to hear the beep sounds continuously.
Wi-Fi link method:(three pairing methods)
Complete the wiring of the switch module before pairing
This WiFi switch module fits for rocker light
switch and reset switch meanwhile.Please pay
attention to the different pairing modes.
Wiring Instructions and Diagrams
1.Turn off the power supply before carrying out any
electrical installation work.
Notes: Put your smartphone close to the switch
sure you have min. 50% Wi-Fi signal.
module when you’re configuring, and make
EnglishEnglish EnglishEnglish
EnglishEnglish EnglishEnglish
3. With Wall Socket
L N
Wall Socket
2.Connect wires according to the wiring diagram.
3.Insert the module into the junction box.
4.Connect the power supply and follow switch module
configuration instructions.
Reset button
Rocker switch Push wall switch
(Reset switch)
Fit for the two switches
Note:
3
2
Registration or Log in
Download “Smart Life”Application
Enter the Register/Login interface;tap
“Register” to create an account by entering
your phone number to get verification code
and “Set password”.Choose “Log in” if you
already have a Smart Life account.
Configure the APP to the switch
Preparation: Ensure the switch has been
connected with electricity;ensure your phone has
been connected to Wi-Fi and is able to connect
to the Internet.
Download Smart Life App
Please scan the QR code or download Smart
Life on App store.
Add Devices
1
3.1 Method one:
Scan the QR code to configure the network guide.
⑴ ⑵
Scan the QR code Please connect the device
according to the
configuration process.
2.Open Smart Life/Tuya App and Click“+”,then
the prompt page will automatically show on the
screen.Click “Add”.
3.2 Method two :
Pair and clear up the WiFi code withBluetooth and
WiFi connected meantime.(New Updated)
1.Confirm the device beeps continuously, if not,
please refer to page 14 for how to enter the
network configuration.
WiFi Smart Switch
3.Select the device you want to add and click “+”

How to reset/re-pair WiFi code
Note:
FAQ
Q1: What should I do if I can’t configure the switch module?
a. Please check whether device is powered on.
b. Make sure your mobile and switch module are under the
same 2.4 GHz WiFi network.
c. Whether it’s in good internet conditions.
d. Make sure the password entered in App is correct.
e. Make sure the wiring is correct.
Q2: What device can be connected to this WiFi switch
module?
Q3: What happens if the WiFi goes off?
Most of your household electrical appliances can be, such as
lamps, laundry machine, coffe maker, etc.
You can still control the device connected the switch module
with your traditional switch and once WiFi is active again the
device connected to module will connect automatically to your
WiFi network.
Q4: What should I do if I change the WiFi network or
change the password?
You have to re-connect our WiFi switch module to the
new WiFi network according to the App User Manual.
9 10 11 12
14
13 15 16
b. For reset switch (Set as reset switch in APP) :
press the switch button for 10 times to hear the
beep sounds continuously.
(If using rocker light switch，you should press the
rocker light switch for 20 times)
c. For rocker light switch (Set as rocker switch in
APP)
: press the switch button for 10 times(ON/OFF
cycle for 5 times) to hear the beep sounds
continuously.
(If using reset switch，you should press the reset
switch for 5 times)
a. For reset button
: long press the button on the
module to hear the beep sounds continuously.
Wi-Fi link method:(three pairing methods)
Complete the wiring of the switch module before pairing
This WiFi switch module fits for rocker light
switch and reset switch meanwhile.Please pay
attention to the different pairing modes.
Wiring Instructions and Diagrams
1.Turn off the power supply before carrying out any
electrical installation work.
Notes: Put your smartphone close to the switch
sure you have min. 50% Wi-Fi signal.
module when you’re configuring, and make
EnglishEnglish EnglishEnglish
EnglishEnglish EnglishEnglish
3. With Wall Socket
L N
Wall Socket
2.Connect wires according to the wiring diagram.
3.Insert the module into the junction box.
4.Connect the power supply and follow switch module
configuration instructions.
Reset button
Rocker switch Push wall switch
(Reset switch)
Fit for the two switches
Note:
3
2
Registration or Log in
Download “Smart Life”Application
Enter the Register/Login interface;tap
“Register” to create an account by entering
your phone number to get verification code
and “Set password”.Choose “Log in” if you
already have a Smart Life account.
Configure the APP to the switch
Preparation: Ensure the switch has been
connected with electricity;ensure your phone has
been connected to Wi-Fi and is able to connect
to the Internet.
Download Smart Life App
Please scan the QR code or download Smart
Life on App store.
Add Devices
1
3.1 Method one:
Scan the QR code to configure the network guide.
⑴ ⑵
Scan the QR code Please connect the device
according to the
configuration process.
2.Open Smart Life/Tuya App and Click“+”,then
the prompt page will automatically show on the
screen.Click “Add”.
3.2 Method two :
Pair and clear up the WiFi code withBluetooth and
WiFi connected meantime.(New Updated)
1.Confirm the device beeps continuously, if not,
please refer to page 14 for how to enter the
network configuration.
WiFi Smart Switch
3.Select the device you want to add and click “+”

How to reset/re-pair WiFi code
Note:
FAQ
Q1: What should I do if I can’t configure the switch module?
a. Please check whether device is powered on.
b. Make sure your mobile and switch module are under the
same 2.4 GHz WiFi network.
c. Whether it’s in good internet conditions.
d. Make sure the password entered in App is correct.
e. Make sure the wiring is correct.
Q2: What device can be connected to this WiFi switch
module?
Q3: What happens if the WiFi goes off?
Most of your household electrical appliances can be, such as
lamps, laundry machine, coffe maker, etc.
You can still control the device connected the switch module
with your traditional switch and once WiFi is active again the
device connected to module will connect automatically to your
WiFi network.
Q4: What should I do if I change the WiFi network or
change the password?
You have to re-connect our WiFi switch module to the
new WiFi network according to the App User Manual.
9 10 11 12
14
13 15 16
b. For reset switch (Set as reset switch in APP) :
press the switch button for 10 times to hear the
beep sounds continuously.
(If using rocker light switch，you should press the
rocker light switch for 20 times)
c. For rocker light switch (Set as rocker switch in
APP)
: press the switch button for 10 times(ON/OFF
cycle for 5 times) to hear the beep sounds
continuously.
(If using reset switch，you should press the reset
switch for 5 times)
a. For reset button
: long press the button on the
module to hear the beep sounds continuously.
Wi-Fi link method:(three pairing methods)
Complete the wiring of the switch module before pairing
This WiFi switch module fits for rocker light
switch and reset switch meanwhile.Please pay
attention to the different pairing modes.
Wiring Instructions and Diagrams
1.Turn off the power supply before carrying out any
electrical installation work.
Notes: Put your smartphone close to the switch
sure you have min. 50% Wi-Fi signal.
module when you’re configuring, and make
EnglishEnglish EnglishEnglish
EnglishEnglish EnglishEnglish
3. With Wall Socket
L N
Wall Socket
2.Connect wires according to the wiring diagram.
3.Insert the module into the junction box.
4.Connect the power supply and follow switch module
configuration instructions.
Reset button
Rocker switch Push wall switch
(Reset switch)
Fit for the two switches
Note:
3
2
Registration or Log in
Download “Smart Life”Application
Enter the Register/Login interface;tap
“Register” to create an account by entering
your phone number to get verification code
and “Set password”.Choose “Log in” if you
already have a Smart Life account.
Configure the APP to the switch
Preparation: Ensure the switch has been
connected with electricity;ensure your phone has
been connected to Wi-Fi and is able to connect
to the Internet.
Download Smart Life App
Please scan the QR code or download Smart
Life on App store.
Add Devices
1
3.1 Method one:
Scan the QR code to configure the network guide.
⑴ ⑵
Scan the QR code Please connect the device
according to the
configuration process.
2.Open Smart Life/Tuya App and Click“+”,then
the prompt page will automatically show on the
screen.Click “Add”.
3.2 Method two :
Pair and clear up the WiFi code withBluetooth and
WiFi connected meantime.(New Updated)
1.Confirm the device beeps continuously, if not,
please refer to page 14 for how to enter the
network configuration.
WiFi Smart Switch
3.Select the device you want to add and click “+”

How to reset/re-pair WiFi code
Note:
FAQ
Q1: What should I do if I can’t configure the switch module?
a. Please check whether device is powered on.
b. Make sure your mobile and switch module are under the
same 2.4 GHz WiFi network.
c. Whether it’s in good internet conditions.
d. Make sure the password entered in App is correct.
e. Make sure the wiring is correct.
Q2: What device can be connected to this WiFi switch
module?
Q3: What happens if the WiFi goes off?
Most of your household electrical appliances can be, such as
lamps, laundry machine, coffe maker, etc.
You can still control the device connected the switch module
with your traditional switch and once WiFi is active again the
device connected to module will connect automatically to your
WiFi network.
Q4: What should I do if I change the WiFi network or
change the password?
You have to re-connect our WiFi switch module to the
new WiFi network according to the App User Manual.
9 10 11 12
14
13 15 16
b. For reset switch (Set as reset switch in APP) :
press the switch button for 10 times to hear the
beep sounds continuously.
(If using rocker light switch，you should press the
rocker light switch for 20 times)
c. For rocker light switch (Set as rocker switch in
APP)
: press the switch button for 10 times(ON/OFF
cycle for 5 times) to hear the beep sounds
continuously.
(If using reset switch，you should press the reset
switch for 5 times)
a. For reset button
: long press the button on the
module to hear the beep sounds continuously.
Wi-Fi link method:(three pairing methods)
Complete the wiring of the switch module before pairing
This WiFi switch module fits for rocker light
switch and reset switch meanwhile.Please pay
attention to the different pairing modes.
Wiring Instructions and Diagrams
1.Turn off the power supply before carrying out any
electrical installation work.
Notes: Put your smartphone close to the switch
sure you have min. 50% Wi-Fi signal.
module when you’re configuring, and make
EnglishEnglish EnglishEnglish
EnglishEnglish EnglishEnglish
3. With Wall Socket
L N
Wall Socket
2.Connect wires according to the wiring diagram.
3.Insert the module into the junction box.
4.Connect the power supply and follow switch module
configuration instructions.
Reset button
Rocker switch Push wall switch
(Reset switch)
Fit for the two switches
Note:
3
2
Registration or Log in
Download “Smart Life”Application
Enter the Register/Login interface;tap
“Register” to create an account by entering
your phone number to get verification code
and “Set password”.Choose “Log in” if you
already have a Smart Life account.
Configure the APP to the switch
Preparation: Ensure the switch has been
connected with electricity;ensure your phone has
been connected to Wi-Fi and is able to connect
to the Internet.
Download Smart Life App
Please scan the QR code or download Smart
Life on App store.
Add Devices
1
3.1 Method one:
Scan the QR code to configure the network guide.
⑴ ⑵
Scan the QR code Please connect the device
according to the
configuration process.
2.Open Smart Life/Tuya App and Click“+”,then
the prompt page will automatically show on the
screen.Click “Add”.
3.2 Method two :
Pair and clear up the WiFi code withBluetooth and
WiFi connected meantime.(New Updated)
1.Confirm the device beeps continuously, if not,
please refer to page 14 for how to enter the
network configuration.
WiFi Smart Switch
3.Select the device you want to add and click “+”

How to reset/re-pair WiFi code
Note:
FAQ
Q1: What should I do if I can’t configure the switch module?
a. Please check whether device is powered on.
b. Make sure your mobile and switch module are under the
same 2.4 GHz WiFi network.
c. Whether it’s in good internet conditions.
d. Make sure the password entered in App is correct.
e. Make sure the wiring is correct.
Q2: What device can be connected to this WiFi switch
module?
Q3: What happens if the WiFi goes off?
Most of your household electrical appliances can be, such as
lamps, laundry machine, coffe maker, etc.
You can still control the device connected the switch module
with your traditional switch and once WiFi is active again the
device connected to module will connect automatically to your
WiFi network.
Q4: What should I do if I change the WiFi network or
change the password?
You have to re-connect our WiFi switch module to the
new WiFi network according to the App User Manual.
9 10 11 12
14
13 15 16
b. For reset switch (Set as reset switch in APP) :
press the switch button for 10 times to hear the
beep sounds continuously.
(If using rocker light switch，you should press the
rocker light switch for 20 times)
c. For rocker light switch (Set as rocker switch in
APP)
: press the switch button for 10 times(ON/OFF
cycle for 5 times) to hear the beep sounds
continuously.
(If using reset switch，you should press the reset
switch for 5 times)
a. For reset button
: long press the button on the
module to hear the beep sounds continuously.
Wi-Fi link method:(three pairing methods)
Complete the wiring of the switch module before pairing
This WiFi switch module fits for rocker light
switch and reset switch meanwhile.Please pay
attention to the different pairing modes.
Wiring Instructions and Diagrams
1.Turn off the power supply before carrying out any
electrical installation work.
Notes: Put your smartphone close to the switch
sure you have min. 50% Wi-Fi signal.
module when you’re configuring, and make
EnglishEnglish EnglishEnglish
EnglishEnglish EnglishEnglish
3. With Wall Socket
L N
Wall Socket
2.Connect wires according to the wiring diagram.
3.Insert the module into the junction box.
4.Connect the power supply and follow switch module
configuration instructions.
Reset button
Rocker switch Push wall switch
(Reset switch)
Fit for the two switches
Note:
3
2
Registration or Log in
Download “Smart Life”Application
Enter the Register/Login interface;tap
“Register” to create an account by entering
your phone number to get verification code
and “Set password”.Choose “Log in” if you
already have a Smart Life account.
Configure the APP to the switch
Preparation: Ensure the switch has been
connected with electricity;ensure your phone has
been connected to Wi-Fi and is able to connect
to the Internet.
Download Smart Life App
Please scan the QR code or download Smart
Life on App store.
Add Devices
1
3.1 Method one:
Scan the QR code to configure the network guide.
⑴ ⑵
Scan the QR code Please connect the device
according to the
configuration process.
2.Open Smart Life/Tuya App and Click“+”,then
the prompt page will automatically show on the
screen.Click “Add”.
3.2 Method two :
Pair and clear up the WiFi code withBluetooth and
WiFi connected meantime.(New Updated)
1.Confirm the device beeps continuously, if not,
please refer to page 14 for how to enter the
network configuration.
WiFi Smart Switch
3.Select the device you want to add and click “+”

How to reset/re-pair WiFi code
Note:
FAQ
Q1: What should I do if I can’t configure the switch module?
a. Please check whether device is powered on.
b. Make sure your mobile and switch module are under the
same 2.4 GHz WiFi network.
c. Whether it’s in good internet conditions.
d. Make sure the password entered in App is correct.
e. Make sure the wiring is correct.
Q2: What device can be connected to this WiFi switch
module?
Q3: What happens if the WiFi goes off?
Most of your household electrical appliances can be, such as
lamps, laundry machine, coffe maker, etc.
You can still control the device connected the switch module
with your traditional switch and once WiFi is active again the
device connected to module will connect automatically to your
WiFi network.
Q4: What should I do if I change the WiFi network or
change the password?
You have to re-connect our WiFi switch module to the
new WiFi network according to the App User Manual.
9 10 11 12
14
13 15 16
b. For reset switch (Set as reset switch in APP) :
press the switch button for 10 times to hear the
beep sounds continuously.
(If using rocker light switch，you should press the
rocker light switch for 20 times)
c. For rocker light switch (Set as rocker switch in
APP)
: press the switch button for 10 times(ON/OFF
cycle for 5 times) to hear the beep sounds
continuously.
(If using reset switch，you should press the reset
switch for 5 times)
a. For reset button
: long press the button on the
module to hear the beep sounds continuously.
Wi-Fi link method:(three pairing methods)
Complete the wiring of the switch module before pairing
This WiFi switch module fits for rocker light
switch and reset switch meanwhile.Please pay
attention to the different pairing modes.
Wiring Instructions and Diagrams
1.Turn off the power supply before carrying out any
electrical installation work.
Notes: Put your smartphone close to the switch
sure you have min. 50% Wi-Fi signal.
module when you’re configuring, and make
EnglishEnglish EnglishEnglish
EnglishEnglish EnglishEnglish
3. With Wall Socket
L N
Wall Socket
2.Connect wires according to the wiring diagram.
3.Insert the module into the junction box.
4.Connect the power supply and follow switch module
configuration instructions.
Reset button
Rocker switch Push wall switch
(Reset switch)
Fit for the two switches
Note:
3
2
Registration or Log in
Download “Smart Life”Application
Enter the Register/Login interface;tap
“Register” to create an account by entering
your phone number to get verification code
and “Set password”.Choose “Log in” if you
already have a Smart Life account.
Configure the APP to the switch
Preparation: Ensure the switch has been
connected with electricity;ensure your phone has
been connected to Wi-Fi and is able to connect
to the Internet.
Download Smart Life App
Please scan the QR code or download Smart
Life on App store.
Add Devices
1
3.1 Method one:
Scan the QR code to configure the network guide.
⑴ ⑵
Scan the QR code Please connect the device
according to the
configuration process.
2.Open Smart Life/Tuya App and Click“+”,then
the prompt page will automatically show on the
screen.Click “Add”.
3.2 Method two :
Pair and clear up the WiFi code withBluetooth and
WiFi connected meantime.(New Updated)
1.Confirm the device beeps continuously, if not,
please refer to page 14 for how to enter the
network configuration.
WiFi Smart Switch
3.Select the device you want to add and click “+”

17 18 19 20
21 22 23 24
EnglishEnglish EnglishEnglish
EnglishEnglish EnglishEnglish
4.Enter Wi-Fi Password and click “Next”,waiting
for completing the connection.
5.Add the device successfully, you can edit the
name of the device to enter the device page by
click “Done”
3.3 Method three:
Pair with traditional pairing method
Open the App, select “+” on top right and choose
“Switch (Wi-Fi)” to add device.
The connecting will take about 10-120 seconds to
complete depending on your network condition.
When pairing is done, the switch will be shown on
the App.
Make sure your smart phone and WiFi switch module
are under the same WiFi network at 2.4 GHz
connection.Confirm when the switch module beeping
rapidly.
7
WiFi Smart Switch
How to achieve multi-control association
Note:Please confirm you have successfully finished
the WiFi link method above for adding this switch
to your Smart Life App before the association.
1.WiFi add another smart switch to the same
Smart Life/Tuya App.(If there is a smart switch
having been added before to the app,just go to
next step.)
Note:There is no need to wire the new added
switch to the light,only L and N are required for
wiring.
3.3
2.Then you will see two devices in the app and
click the main switch(as One gang switch as
below) by entering into the next operation.
Main Switch New Added
Switch
3.Click in the upper right corner and
choose“Multi-Control Association, and then click
“+” in the right corner
4.Choose the switch that you want to associate
to and then choose the switch button that you
want to control the same light.
5.Then go back to previous page,you will see two
items in the page,one is your main switch,the other is
the one you associate just now.
Note:Please confirm the associated switch is
enabled.
6.Now you are able to control your light with two
switches.Do not associate another button in the
same switch for multi-control.
7.If you want to add another third or more smart
switches to control your light,just repeat the steps
above.And you will see the result as below when
you associate another new switch.
Associated 1
Associated 2
Main Switch

17 18 19 20
21 22 23 24
EnglishEnglish EnglishEnglish
EnglishEnglish EnglishEnglish
4.Enter Wi-Fi Password and click “Next”,waiting
for completing the connection.
5.Add the device successfully, you can edit the
name of the device to enter the device page by
click “Done”
3.3 Method three:
Pair with traditional pairing method
Open the App, select “+” on top right and choose
“Switch (Wi-Fi)” to add device.
The connecting will take about 10-120 seconds to
complete depending on your network condition.
When pairing is done, the switch will be shown on
the App.
Make sure your smart phone and WiFi switch module
are under the same WiFi network at 2.4 GHz
connection.Confirm when the switch module beeping
rapidly.
7
WiFi Smart Switch
How to achieve multi-control association
Note:Please confirm you have successfully finished
the WiFi link method above for adding this switch
to your Smart Life App before the association.
1.WiFi add another smart switch to the same
Smart Life/Tuya App.(If there is a smart switch
having been added before to the app,just go to
next step.)
Note:There is no need to wire the new added
switch to the light,only L and N are required for
wiring.
3.3
2.Then you will see two devices in the app and
click the main switch(as One gang switch as
below) by entering into the next operation.
Main Switch New Added
Switch
3.Click in the upper right corner and
choose“Multi-Control Association, and then click
“+” in the right corner
4.Choose the switch that you want to associate
to and then choose the switch button that you
want to control the same light.
5.Then go back to previous page,you will see two
items in the page,one is your main switch,the other is
the one you associate just now.
Note:Please confirm the associated switch is
enabled.
6.Now you are able to control your light with two
switches.Do not associate another button in the
same switch for multi-control.
7.If you want to add another third or more smart
switches to control your light,just repeat the steps
above.And you will see the result as below when
you associate another new switch.
Associated 1
Associated 2
Main Switch

17 18 19 20
21 22 23 24
EnglishEnglish EnglishEnglish
EnglishEnglish EnglishEnglish
4.Enter Wi-Fi Password and click “Next”,waiting
for completing the connection.
5.Add the device successfully, you can edit the
name of the device to enter the device page by
click “Done”
3.3 Method three:
Pair with traditional pairing method
Open the App, select “+” on top right and choose
“Switch (Wi-Fi)” to add device.
The connecting will take about 10-120 seconds to
complete depending on your network condition.
When pairing is done, the switch will be shown on
the App.
Make sure your smart phone and WiFi switch module
are under the same WiFi network at 2.4 GHz
connection.Confirm when the switch module beeping
rapidly.
7
WiFi Smart Switch
How to achieve multi-control association
Note:Please confirm you have successfully finished
the WiFi link method above for adding this switch
to your Smart Life App before the association.
1.WiFi add another smart switch to the same
Smart Life/Tuya App.(If there is a smart switch
having been added before to the app,just go to
next step.)
Note:There is no need to wire the new added
switch to the light,only L and N are required for
wiring.
3.3
2.Then you will see two devices in the app and
click the main switch(as One gang switch as
below) by entering into the next operation.
Main Switch New Added
Switch
3.Click in the upper right corner and
choose“Multi-Control Association, and then click
“+” in the right corner
4.Choose the switch that you want to associate
to and then choose the switch button that you
want to control the same light.
5.Then go back to previous page,you will see two
items in the page,one is your main switch,the other is
the one you associate just now.
Note:Please confirm the associated switch is
enabled.
6.Now you are able to control your light with two
switches.Do not associate another button in the
same switch for multi-control.
7.If you want to add another third or more smart
switches to control your light,just repeat the steps
above.And you will see the result as below when
you associate another new switch.
Associated 1
Associated 2
Main Switch

17 18 19 20
21 22 23 24
EnglishEnglish EnglishEnglish
EnglishEnglish EnglishEnglish
4.Enter Wi-Fi Password and click “Next”,waiting
for completing the connection.
5.Add the device successfully, you can edit the
name of the device to enter the device page by
click “Done”
3.3 Method three:
Pair with traditional pairing method
Open the App, select “+” on top right and choose
“Switch (Wi-Fi)” to add device.
The connecting will take about 10-120 seconds to
complete depending on your network condition.
When pairing is done, the switch will be shown on
the App.
Make sure your smart phone and WiFi switch module
are under the same WiFi network at 2.4 GHz
connection.Confirm when the switch module beeping
rapidly.
7
WiFi Smart Switch
How to achieve multi-control association
Note:Please confirm you have successfully finished
the WiFi link method above for adding this switch
to your Smart Life App before the association.
1.WiFi add another smart switch to the same
Smart Life/Tuya App.(If there is a smart switch
having been added before to the app,just go to
next step.)
Note:There is no need to wire the new added
switch to the light,only L and N are required for
wiring.
3.3
2.Then you will see two devices in the app and
click the main switch(as One gang switch as
below) by entering into the next operation.
Main Switch New Added
Switch
3.Click in the upper right corner and
choose“Multi-Control Association, and then click
“+” in the right corner
4.Choose the switch that you want to associate
to and then choose the switch button that you
want to control the same light.
5.Then go back to previous page,you will see two
items in the page,one is your main switch,the other is
the one you associate just now.
Note:Please confirm the associated switch is
enabled.
6.Now you are able to control your light with two
switches.Do not associate another button in the
same switch for multi-control.
7.If you want to add another third or more smart
switches to control your light,just repeat the steps
above.And you will see the result as below when
you associate another new switch.
Associated 1
Associated 2
Main Switch