Moen FOUR-INCH CENTERSET 4200 User manual


LAVATORY FAUCETS
Four-Inch Centerset
4200, 4220, 4330, 4340, 4350,
4400, 4641, 4643 SERIES
INSTALLATION INSTRUCTIONS
THESE INSTRUCTIONS MUST BE
LEFT WITH HOMEOWNER
MT123A
®
CAUTION: Always turn water off before disassembling the valve. Open valve handle to alleviate water
pressure to insure that complete water shut-off has been accomplished.
Before turning water on during either rough-in or trim-out, make sure that the cartridge retainer clip is in place. The cartridge and
retainer clip were properly installed and tested before leaving the factory. Although it is unlikely, it is nevertheless possible that
throughthehandlingofthevalvebyanynumberofpersonstheretainerclipmaynotbeproperlyinstalled. Thisshouldbecarefully
checked at time of rough-in and trim-out. If the retainer clip is not properly installed, water pressure could force the cartridge out
of the casting. Personal injury or water damage to the premises could result.
Clip
Ear
6" X 2" WIDE
1/2" IPS
THREADED
CONNECTIONS
LIFT ROD
POSITION
USE SPACER TO INSTALL
ON THINNER LAVATORY
BOWLS OR COUNTERS
DISCARD SPACER WHEN
INSTALLING ON THICKER
LAVATORY BOWLS OR COUNTERS
1-3/4"
MAX.
4-3/4"
3-5/8" C.C.
1-3/4"
5" NOMINAL
OPEN
POSITION
5" NOMINAL
OPEN
POSITION
CONCENTRIX HANDLE
HANDLE INSERT
(NOT
INCLUDED)
3-5/8" C.C.
1-3/4"
3-5/8" C.C.
1-3/4"
5" NOMINAL
OPEN
POSITION
LEVER HANDLE KNOB HANDLE
TILT BACK
CLAMP BAR
With clamp bar, spacer and
mounting nut installed, tilt
clamp bar back as shown,
then drop faucet supplies
down through deck holes and
tighten from below. On decks
thicker than 3/4" you may
have to remove spacer.
Fits 4" centers and through a 1" minimum diameter hole.
All models equipped with a Moen Flow-Rator™.
Complies with ASME A112.18.1M and CSA B125

Lift Rod & Waste Assembly
(For model with grid strainer assembly follow steps 1-3 only)
1. Thoroughly clean around drain opening in lavatory basin. Apply
1/4 inch bead of plumber's putty (not furnished) around the
underside of seat (as shown).
2. Apply pipe joint compound or Teflon tape (not furnished) to top
threaded end of the drain body. Slip drain body up through the
drain opening and screw seat on the drain body.
3. Position the drain body (with pivot rod opening extending rear-
ward)andtightenmountingnutuntilthedrainbodyissnug. Wipe
excess plumber's putty from the seat area. Apply pipe joint
compound (not furnished) to top threaded end of tailpipe and
screw into the drain body. Tighten firmly by hand.
4. Position the drain plug in either of the following ways:
A. VANDALPROOF - This design is to prevent unauthorized
removal of the drain plug. Unscrew the pivot nut and remove
the pivot rod. Inside the drain body position the pivot rod
through the drain plug hole as shown in the illustration below.
Screw the pivot nut back on the drain body. DO NOT
OVERTIGHTEN.
B. EASY REMOVAL - This design is for quick removal of drain
plug for cleaning. Just drop in the drain plug as shown in the
illustration below.
5. Hookupliftrodandknob,liftrodstrapandspringclampasshown.
6. With the drain plug in full open position, adjust lift rod and knob to
clear faucet and tighten lift rod strap screw.
DRAIN
PLUG
VANDALPROOF
HOLE
LIFT ROD
AND KNOB
LIFT ROD
STRAP
SCREW
SPRING
CLIP
LIFT ROD
STRAP
PIVOT
ROD
BOTTOM GASKET
FLAT WASHER
PIVOT NUT
PIVOT ROD
SEAT
2-1/8"
1-1/2"
PIPE
JOINT
COMPOUND
OR TEFLON
TAPE
(NOT
FURNISHED)
SEAT
PLUMBERS
PUTTY
MAX 2-1/2"
MIN 1-1/2"
MOUNTING
NUT
DRAIN
BODY
PIPE
JOINT
COMPOUND
(NOT
FURNISHED)
1-1/4"
TAILPIPE
BASIN
8"
FAUCET
CONNECTION
NIPPLE
TIGHTEN
NUT
HOLD WITH
WRENCH
Installation
Be sure lavatory or mounting surface is clean and dry. Place a bead of plumber's putty around the inside lip of the
gasket. Lay gasket on deck and place faucet supplies and studs down through deck holes. Position faucet. Fasten
faucet to deck, using clamp bars, spacers (if necessary), and mounting nuts on studs. Tighten. Engage tailpiece nuts on
supplies to faucet nipples. Tighten nuts.
B. EASY REMOVAL
A. VANDALPROOF
PIVOT
ROD VANDALPROOF
POSITION
POSITION FOR
EASY REMOVAL
PIVOT
ROD
MT123A
WARNING: Hold the faucet connection nipples with a wrench when
tightening to prevent twisting and collapse of the tubing.
Flushing
IMPORTANT:
Pipe chips, sand, stones and other solids found in new and renovated plumbing can damage the sealing surface of the
faucet cartridge and cause a leak. To avoid damage, DO NOT OPERATE VALVE until you have followed these instruc-
tions: a. Make sure all water supplies are OFF.
b. Remove handle parts, stop tube, retainer clip and cartridge (see "Disassembly" for detailed instructions).
c. At the supplies, slowly turn both hot and cold water on and thoroughly flush out the body and lines.

Disassembly
CAUTION: Turn OFF both hot and cold water supplies. Open handle to alleviate water pressure to insure that
complete water shut-off has been accomplished.
For Knob Models:
1. Remove handle cover, handle screw, knob, stop tube, washer, and retainer clip.
For Concentrix Handle Models:
1. Remove handle cover, gasket, handle screw, handle insert, handle skirt, handle adapter, stop tube, and retainer clip.
For Lever Handle Models:
1. Remove handle cap and handle screw. Lift handle assembly up, keeping cartridge stem in down position and tilt up
and off. Remove clip retainer ring and retainer clip. Slide off grooved sleeve and spacer.
For All Models:
2. Using pliers, grasp the cartridge stem and pull out the cartridge. If cartridge is difficult to remove, turn the cartridge
shell back and forth with the Moen cartridge wrench (furnished with the new Moen cartridge) or use a Moen cartridge
puller.
H
C
STOP
TUBE KNOB
HANDLE
SCREW
O-RING
HANDLE
COVER
WASHER
HANDLE
SCREW
HANDLE
COVER
STOP
TUBE
HANDLE
ADAPTER
SKIRT
HANDLE
INSERT
(NOT INCLUDED)
SPACER
CLIP
RETAINER
RING
GROOVED
SLEEVE
HANDLE
ASSEMBLY
HANDLE
SCREW
HANDLE
COVER
RETAINER
CLIP
CARTRIDGE
GASKET
Reassembly
Fully insert the cartridge until the top of the cartridge ears are level with the top of the faucet body. Position the cartridge
ears up and down to allow insertion of the retainer clip. The notched flat on the stem must point UP when mounting Knob
or Concentrix Handles, DOWN for Lever Handle models. Replace the retainer clip (for lever handles replace spacer,
grooved sleeve, retainer clip, and clip retainer ring) so that the legs straddle the cartridge ears and slide down into the
bottom slot in the body. This prevents the cartridge from rotating and locks it in the body. Reinstall handle parts. Tighten
handle screw securely. Press on handle cover. For Concentrix models install handle insert onto adapter (align locator
notch on handle insert with key on adapter). NOTE: Locator notch on the handle insert must be on the bottom. Fit gasket
up into handle cover recess. Replace handle cover and hand tighten.
To Eliminate Cross-Piping on Back-To-Back Installations,
or To Correct Reversed Rough-In Where Hot and Cold Positions Are Reversed
Remove handle parts and stop tube (see "Disassembly"). Turn cartridge stem around so that the notched flat is turned
one half turn or 180°. Reinstall handle parts. Tighten handle screw securely; replace handle cover.
Cleaning & Care Instructions for
Special Finish Models:
All that is necessary to clean these faucets is to wipe them with a soft, damp cloth such as terrycloth. Warm water will
remove dry water spots. CAUTION: DO NOT use cleansers which contain abrasives or harsh chemicals. NEVER use
alcohol or other organic solvents. A high quality, non abrasive wax polish applied occasionally will help to preserve the
deep tones of the finish.

Moen Incorporated 25300 Al Moen Drive, North Olmsted, OH 44070-8022, U.S.A.
In Canada:
Moen Inc. 2816 Bristol Circle, Oakville, Ontario L6H5S7
MT123A SEP 95
© Copyright 1995
Moen Incorporated
Printed in U.S.A.
Consumer Information
Faucets made of leaded brass alloys may contribute small amounts of lead to water that is allowed to stand in contact
with the brass. The amount of lead contributed by any faucet is highest when the faucet is new. The following steps may
reduce potential exposure to lead from faucets and other parts of the plumbing system:
• Always run the water for a few seconds prior to use for drinking or cooking.
• Use only cold water for drinking or cooking.
• If you wish to flush the entire plumbing system of water that has been standing in the pipes or other fittings, run the
cold water until the temperature of the water drops, indicating water coming from the outside main.
• If you are concerned about lead in your water, have your water tested by a certified laboratory in your area.
HELPLINE:
For answers to any product, installation,
replacment parts or warranty questions,
call our consumer helplines.
In the U.S., toll free:
1-800-321-6636
In Canada call:
Toronto, 905-829-3400
Rest of Canada, 1-800-465-6130

®