Money Controls SR3 User manual

SR3 TSP065.doc Issue 1.1 – June 2004
This document is the copyright of Money Controls Ltd and may not be reproduced in part or in total by any means,
electronic or otherwise, without the written permission of Money Controls Ltd. Money Controls Ltd does not accept
liability for any errors or omissions contained within this document. Money Controls Ltd shall not incur any
penalties arising out of the adherence to, interpretation of, or reliance on, this standard. Money Controls Ltd will
provide full support for this product when used as described within this document. Use in applications not covered
or outside the scope of this document may not be supported. Money Controls Ltd. reserves the right to amend,
improve or change the product referred to within this document or the document itself at any time.
©Money Controls 2004. All rights reserved.

SR3 TSP065.doc Issue 1.1 – June 2004
©Money Controls 2004. All rights reserved.
Page 2 of 7
Contents
1. Diary of Changes........................................................................................................................................... 3
2. Introduction.................................................................................................................................................... 4
3. Overview of test box ..................................................................................................................................... 5
3.1 Test Box Functions.................................................................................................................................. 5
3.1.1 ACCEPT LINES............................................................................................................................... 5
3.1.2 INHIBIT / ENABLE SWITCHES....................................................................................................... 6
3.1.3 REJECT LED................................................................................................................................... 6
Tables
Table 1: SR3 Mode 1 Credits .................................................................................................................................. 5

SR3 TSP065.doc Issue 1.1 – June 2004
©Money Controls 2004. All rights reserved.
Page 3 of 7
1. Diary of Changes
Issue 1.0…………………………………………………………………….….…………29th April 03
Issue 1.1…………………………………………………………………….….………….30th June 04
¾Changed footer

SR3 TSP065.doc Issue 1.1 – June 2004
©Money Controls 2004. All rights reserved.
Page 4 of 7
2. Introduction
The test box has been designed to allow the testing of selected parallel functions of any SR3
acceptor. In order to function, the test box must be supplied with 12V - 24V DC.

SR3 TSP065.doc Issue 1.1 – June 2004
©Money Controls 2004. All rights reserved.
Page 5 of 7
3. Overview of test box
There are DC inputs on the side of the box, along with a master ON / OFF switch. There is 1
acceptor loom emanating from the right side of the test box – the 10-way header connects to
the PARALLEL interface connector of the SR3.
DO NOT TURN THE POWER ON BEFORE ALL CONNECTIONS BETWEEN THE TEST BOX
AND ACCEPTOR ARE MADE!!!!!!
3.1 Test Box Functions
The following are the functions available for this test box.
3.1.1 ACCEPT LINES
These are LED’s which are lit when the parallel connector’s accept lines are activated.
Their operation depends upon the Mode of acceptor connected. Table 1 shows the
standard credit codes for the Mode1 SR3.
Table 1: SR3 Mode 1 Credits
SR3 Mode 1 Acceptor
Parallel credits Serial credits
A
1A 2A 3A 4A 5A 6A 1A 2A 3A 4A 5A 6
Coin 1 X X
Coin 2 X X X
Coin 3 X X X
Coin 4 X X X X
Coin 5 X X X
Coin 6 X X X X
Coin 7 X X X X
Coin 8 X X X X X
Coin 9 X X X
Coin 10 X X X X
Coin 11 X X X X
Coin 12 X X X X X
NB – The SR3 cannot have the parallel and the serial credit codes programmed onto its
EEPROM at the same time.
An alarm signal is displayed by all accept lines being activated at the same time (All
LED’s illuminated)

SR3 TSP065.doc Issue 1.1 – June 2004
©Money Controls 2004. All rights reserved.
Page 6 of 7
3.1.2 INHIBIT / ENABLE SWITCHES
As the name suggests these allow the user to enable or disable the coins on the acceptor
through the parallel interface.
3.1.3 REJECT LED
The LED illuminates whenever a reject is detected (Pin 5).

SR3 TSP065.doc Issue 1.1 – June 2004
©Money Controls 2004. All rights reserved.
Page 7 of 7
This manual is intended only to assist the reader in the use of this product and
therefore Money Controls shall not be liable for any loss or damage whatsoever
arising form the use of any information or particulars in, or any incorrect use of the
product. Money Controls reserve the right to change product specifications on any
item without prior notice