Monogram ZV48S User manual

INSTALLATION
INSTRUCTIONS
30”, 36” and 48”
Professional Vent Hoods
Monogram.com

249-80152 Rev. 8
Safety Information
READ AND SAVE THESE INSTRUCTIONS
BEFORE YOU BEGIN
Read these instructions completely and carefully.
■IMPORTANT — Save these instructions
for local inspector’s use.
■
IMPORTANT — Observe all governing
codes and ordinances.
■Note to Installer — Be sure to leave these
instructions with the Consumer.
■Note to Consumer — Keep these instructions with
your Owner’s Manual for future reference.
■Skill Level — Installation of this appliance requires
basic mechanical and electrical skills.
■Completion Time — 1 to 3 Hours.
■Properinstallationistheresponsibilityofthe
installer.Productfailureduetoimproperinstallation
is not covered under the warranty.
■ForMonogramlocalserviceinyourarea,call
1.800.444.1845.
■ForMonogramserviceinCanada,call
1.800.561.3344.
■ForMonogramPartsandAccessories,call
1.800.626.2002.
CAUTION Due to the weight and size of these
vent hoods and to reduce the risk of personal injury
ordamagetotheproduct, TWO PEOPLE ARE
REQUIRED FOR PROPER INSTALLATION.
WARNING To reduce the risk of fire or electrical
shock,donotusethisrangehoodwithanyexternal
solid-statespeedcontroldevice.Anysuchalteration
from original factory wiring could result in damage to
the unit and/or create an electrical safety hazard.
TO REDUCE THE RISK OF FIRE, USE ONLY
METAL DUCTWORK.
WARNING TOREDUCETHERISKOFFIRE,
ELECTRICALSHOCKORINJURYTOPERSONS,
OBSERVETHEFOLLOWING:
A.Usethisunitonlyinthemannerintendedbythe
manufacturer.Ifyouhaveanyquestions,contact
the manufacturer.
B.Beforeservicingorcleaningtheunit,switchthe
power off at the service panel and lock the service
disconnecting means to prevent the power from
beingswitchedonaccidentally.Whentheservice
disconnectingmeanscannotbelocked,securely
fastenaprominentwarningdevice,suchasatag,
to the service panel.
CAUTION FORGENERALVENTILATINGUSE
ONLY.DONOTUSETOEXHAUSTHAZARDOUS
MATERIALS,EXPLOSIVEMATERIALSORVAPORS.
WARNING TOREDUCETHERISKOFFIRE,
ELECTRICALSHOCKORINJURYTOPERSONS,
OBSERVETHEFOLLOWING:
■Installationworkandelectricalwiringmustbedoneby
qualified person(s) in accordance with all applicable
codesandstandards,includingfire-ratedconstruction.
■Sufficientairisneededforpropercombustionand
exhaustingofgasesthroughtheflue(chimney)offuel
burningequipmenttopreventback-drafting.Follow
the heating equipment manufacturer’s guidelines
andsafetystandards,suchasthosepublishedby
theNationalFireProtectionAssociation(NFPA),the
AmericanSocietyforHeating,RefrigerationandAir
ConditioningEngineers(ASHRAE)andthelocalcode
authorities.Whenapplicable,installanymakeup
(replacement) air system in accordance with local
building code requirements. Visit GEAppliances.com
for available makeup air solutions.
■Whencuttingordrillingintowallsorceilings,donot
damage electrical wiring and other hidden utilities.
■Ductedsystemsmustalwaysbeventedtotheoutdoors.
■Localcodesvary.Installationofelectrical
connections and grounding must comply with
applicablecodes.Intheabsenceoflocalcodes,the
ventshouldbeinstalledinaccordancewithNational
ElectricalCodeANSI/NFPA70-1990orlatestedition.
CAUTION To reduce risk of fire and to properly
exhaustair,besuretoductairoutside—donotvent
exhaustairintospaceswithinwallsorceilingsorinto
attics,crawlspacesorgarages.

49-80152 Rev. 8 3
Installation Instructions
CONTENTS
Safety Information ......................................................... 2
ProductDimensions ...................................................... 3
Installation Clearances .................................................. 4
OptionalDuctCoverAccessories ................................. 4
DetermineInstallationHeight,
DuctCoverAccessories............................................. 5
AdvancePlanning ......................................................... 6
PowerSupply ................................................................ 6
DuctFittings .................................................................. 7
Tools and Materials Required ....................................... 8
RemovethePackaging ................................................. 8
PartsProvided............................................................... 9
Step1,DetermineDuctworkandWiringLocations .... 10
Step2A,InstallHoodOntoWall ................................. 11
Step2B,InstallHoodBeneathSoffit........................... 12
Step3,ConnectDuctwork .......................................... 13
Step4,ConnectElectrical........................................... 13
Step5,InstallDuctCovers.......................................... 13
Step6,InstallMotor .................................................... 13
Step7,InstallFilters.................................................... 14
Step8,InstallImplementRods ................................... 14
PRODUCT DIMENSIONS
ModelZV48SWithStraightSides
ModelZV36SWithStraightSides
ModelZV30SWithStraightSides
ModelZV48TWithTaperedSides
ModelZV36TWithTaperedSides
ModelZV30TWithTaperedSides
18"
40"
25" 47-15/16"
12"
18"
47-15/16"
47-15/16"
12"
25"
18"
35-15/16"
35-15/16"
12"
25"
18"
28"
25" 35-15/16"
12"
18"
29-15/16"
29-15/16"
12"
25"
18"
22"
25" 29-15/16"
12"
1” = 2.5 cm; 1’ = 0.3 m

449-80152 Rev. 8
Advance Planning
INSTALLATION CLEARANCES
These vent hoods are designed to be installed onto a
wall or beneath a soffit or cabinet.
■Installthesehoods*30"Min.to36"Max.abovethe
cooking surface.
■Thesehoodsmaybeinstalled24"min.aboveagas
orelectricdrop-instylecooktop.Alwaysobserve
the30"to36"clearancewheninstalledoverany
professional style cooktop or range.
NOTE: Clearances may vary due to type of
cooking product and local codes. Check with local
inspectors to be sure standard is applicable.
In this installation the ductwork running from the top
of the hood will be concealed in the soffit or upper
cabinetry.
Forthisinstallation,adecorativeductcoveris
available to conceal the ductwork running from the
top of the hood. Use of the duct cover requires
special consideration to the installation height above
the countertop.
OPTIONAL DUCT COVER
ACCESSORIES
Standarddecorativeductcoversareavailablein6"
and12"heights.Ductcoversmaybestacked,in
variouscombinations,toconcealtheductworkrunning
from the top of the hood to the ceiling.
■Beforeyoubegin,youshoulddeterminethe
installation height of the hood and order the
correct size duct cover. The duct covers should
be ordered at the same time as the vent hood and
be on site before installation. Order the duct cover
corresponding to your model.
6" Duct Cover
12" Duct Cover
Standard Duct Covers
6" Duct Covers
Hood Model 6” Duct Cover Dimensions
ZV48T,ZV48S ZX48DC6 6"Hx19-11/16"Wx11-7/8"D
ZV36T,ZV36S ZX36DC6 6"Hx15-3/4"Wx11-7/8"D
ZV30T,ZV30S ZX36DC6 6"Hx15-3/4"Wx11-7/8"D
12" Duct Covers
Hood Model 12” Duct Cover Dimensions
ZV48T,ZV48S ZX48DC12 12"Hx19-11/16"Wx11-7/8"D
ZV36T,ZV36S ZX36DC12 12"Hx15-3/4"Wx11-7/8"D
ZV30T,ZV30S ZX36DC12 12"Hx15-3/4"Wx11-7/8"D
SOFFIT
Soffit Installation
30" MIN.
36" MAX.
Wall Mount Installation
30" MIN.
36" MAX.
1” = 2.5 cm; 1’ = 0.3 m

49-80152 Rev. 8 5
Advance Planning
DETERMINE INSTALLATION HEIGHT, DUCT COVER ACCESSORIES
Theseventhoodsmustbeinstalled30”min.to36”max.
abovethestandard36”highcookingsurface.When
installedwiththewarmingshelf,allow32”min.to38”
max.clearance.Theexacthoodinstallationheightis
determined by the ceiling height.
1.Measuretheexactceilingheight.
2. Review the chart at right to determine the range
of possible hood installation heights that can be
accomplished with one or more duct covers.
3. Increase or decrease hood installation height to
accommodatethefixed6”or12”ductcovers.
4.Ductcoversmaybestacked,invariouscombinations,
to reach ceiling heights.
NOTE:MinimumceilingheightforREARWALL
EXHAUSTwithductcoversis8'4"wheninstallingat30"
abovecountertopusing10"elbow
*Basedon36"countertopheight.
NOTE:Additionalductcoversmaybeusedtoreachhigherceilings.
Actual Ceiling
Height
*Possible
Hood
Installation
Height
6” Duct
Covers
12” Duct
Covers
7'11" 35" 1
8'0"
8'0"
30"
36" 1
1
8'1" 31" 1
8'2" 32" 1
8'4" 33" 1
8'4" 34" 1
8'5" 35" 1
8'6"
8'6"
30"
36"
1 1
1
8'7" 31" 1 1
8'8" 32" 1 1
8'9" 33" 1 1
8'10" 34" 1 1
8'11" 35" 1 1
9'0"
9'0"
30"
36" 1
2
1
9'1" 31" 2
9'2" 32" 2
9'3" 33" 2
9'4" 34" 2
9'5" 35" 2
9'6"
9'6"
30"
36" 1
2
1
9'7" 31" 1 2
9'8" 32" 1 2
9'9" 33" 1 2
9'10" 34" 1 2
9'11" 35" 1 2
10'0"
10'0"
30"
36" 1
3
2
10'1" 31" 3
10'2" 32" 3
10'3" 33" 3
10'4" 34" 3
Installation Height
Ceiling Height
to Floor
Duct Covers
18" Hood
Height
Straight or Taper-Sided Hoods
1” = 2.5 cm; 1’ = 0.3 m

649-80152 Rev. 8
Advance Planning
ADVANCE PLANNING
Ductwork Planning
■Theseventhoodsareequippedfor10”round
ductwork.Forbestperformance,use10”round
ductwork on the 48” wide hoods. 30” and 36” hoods
may be transitioned to 8” round.
■Thishoodmaybeventedverticallythroughupper
cabinets,soffitorceiling.Aducttransitionpieceis
suppliedforverticalexhaust.Uselocallysupplied
elbows to vent horizontally through the rear wall.
■Determinetheexactlocationoftheventhood.
■Plantherouteforventingexhausttotheoutdoors.
■Usetheshortestandstraightestductroutepossible.
Forsatisfactoryperformance,ductrunshould
notexceed150ft.equivalentlengthforanyduct
configurations.
■Referto“DuctFittings”charttocomputethe
maximumpermissiblelengthforductrunstothe
outdoors.
■Usemetalductworkonly.
■Installawallcaporroofcapwithdamperatthe
exterioropening.Orderthewallorroofcapandany
transition needed in advance.
■Whenapplicable,installanymakeup(replacement)
air system in accordance with local building
code requirements. Visit GEAppliances.com for
available makeup air solutions.
Wall Framing for Adequate Support
■Theseventhoodsareheavy.Adequatestructural
support must be provided. Hoods must be secured
to vertical studs in the wall.
■Itisstronglyrecommendthattheventhoodwith
duct cover be on site before final framing and wall
finishing. This will also help to accurately locate the
ductwork and electrical service.
Decorative Duct Covers
Decorativeductcovers,6”and12”high,areavailable
to fit all models. The duct cover conceals the ductwork
running from the top of the hood to the ceiling or
soffit. Stack one or more duct covers over the top of
the hood to reach your ceiling height.
POWER SUPPLY
IMPORTANT - (Please read carefully)
WARNING FORPERSONALSAFETY,THIS
APPLIANCEMUSTBEPROPERLYGROUNDED.
Remove house fuse or open circuit breaker before
beginning installation.
Donotuseanextensioncordoradapterplugwith
thisappliance.FollowNationalelectricalcodesor
prevailing local codes and ordinances.
Electrical supply
Theseventhoodsmustbesuppliedwith120V,60Hz,
andconnectedtoanindividual,properlygrounded
branchcircuit,andprotectedbya15or20ampcircuit
breaker or time delay fuse.
■Wiringmustbe2wirewithground.
■Iftheelectricalsupplydoesnotmeettheabove
requirements,callalicensedelectricianbefore
proceeding.
■Routehousewiringasclosetotheinstallation
location as possible on the back wall or ceiling.
■Connectthewiringtothehousewiringin
accordance with local codes.
Grounding instructions
The grounding conductor must be connected to
agroundmetal,permanentwiringsystem,oran
equipment-grounding terminal or lead on the hood.
WARNING The improper connection of the
equipment-grounding conductor can result in a risk
of electric shock. Check with a qualified electrician or
service representative if you are in doubt whether the
appliance is properly grounded.
1” = 2.5 cm; 1’ = 0.3 m

49-80152 Rev. 8 7
Advance Planning
DUCT FITTINGS
Hoods Are Equipped
For 10" Round Duct
Usethischarttocomputemaximum
permissible lengths for duct runs to
outdoors.
NOTE:Donotexceedmaximum
permissible equivalent lengths!
Maximum recommended duct
length for these hoods: 150 feet
Flexible ducting:
Ifflexiblemetalductingisused,
all the equivalent feet values in
the table should be doubled. The
flexiblemetalductshouldbestraight
andsmoothandextendedasmuch
as possible.
DONOTuseflexibleplasticducting.
NOTE:Anyhomeventilation
system,suchasaventilationhood,
may interrupt the proper flow of
combustionairandexhaustrequired
byfireplaces,gasfurnaces,gas
water heaters and other naturally
vented systems. To minimize the
chance of interruption of such
naturallyventedsystems,followthe
heating equipment manufacturer’s
guidelines and safety standards
suchasthosepublishedbyNFPA
andASHRAE.Whenapplicable,
install any makeup (replacement)
air system in accordance with local
building code requirements. Visit
GEAppliances.com for available
makeup air solutions.
Duct Piece Dimensions
Equivalent
Length*
Quantity
Used
Total
Equivalent
Length
10"roundto8"round 5 ft.
Round,straight 1 ft.
(per foot length)
3-1/4"x10"
3-1/4"x12"straight
1 ft.
(per foot length)
90°elbow 8"Dia.17ft.
10"Dia.24ft.
45°elbow 8"Dia.10ft.
10"Dia.14ft.
3-1/4”x12”
3-1/4"x10"
90°elbow
15 ft.
14 ft.
3-1/4"x10"
3-1/4"x12"
45°elbow
8 ft.
9ft.
3-1/4"x10"
3-1/4"x12"
90°flatelbow
33 ft.
36 ft.
10"roundtransition
to3-1/4"x10"or
3-1/4"x12"
9ft.
3-1/4"x10"or
3-1/4"x12"to
10"roundtransition
6 ft.
10"roundto3-1/4"x10"
3-1/4"x12"transition
90°elbow
16 ft.
13 ft.
3-1/4"x10"
3-1/4"x12"to10"round
transition90°elbow
9ft.
8 ft.
Round wall cap
with damper
8"Dia.32ft.
10"Dia.41ft.
3-1/4"x10"
3-1/4"x12"wallcap
with damper
24 ft.
26 ft.
Round roof cap 8"Dia.44ft.
10"Dia.56ft.
Total Duct Run
*Hoodsaresuppliedwitha10”roundtransition.Alocallysupplied
transition is required for other sizes.
NOTE:Outletontopofhoodis8-1/8”x8”.
*Actuallengthofstraightductplusductfittingequivalent.Equivalent
length of duct pieces are based on actual tests conducted by
GEAppliancesEvaluationEngineeringandreflectrequirementsfor
good venting performance with any ventilation hood.
1” = 2.5 cm; 1’ = 0.3 m

849-80152 Rev. 8
Installation Preparation
TOOLS AND MATERIALS REQUIRED
(NOT SUPPLIED)
Pencilandtapemeasure
Pliers
Pliers
Electric or battery operated drill
and1/8",3/8"bits
120V60Hz.15or20Amp,
2-wirewithground.Properly
grounded branch circuit.
Electrical Cable
Key Hole Saw
Key Hole Saw
Hammer
Wire Cutter/Stripper
Wirecutter/
stripper
Step ladder
Ladder
Metal Snips
Metal Snips Saber saw
or Sawzall
Saber Saw
Wirenuts
Wire Nuts
Phillipsandflat
blade screwdrivers
Strain relief for
junction cover.
Strain Relief I
Spirit level
Level 2
Flashlight
Safety glasses
Safety Glasses
762Dia5
10"roundmetal
duct,lengthto
suit installation.
Duct tape
Duct Tape
REMOVE THE PACKAGING
■Liftoutthewoodencrossmember,aswellasthetop
protective carton.
■Liftoutthefour“L”shapedpolystyreneprotection
profiles.
■Removetheprotectionmoldingsaroundthesmaller
cartonbox.
■Removethesmallboxhousingthemotor.
■Liftthehoodoutofthebox.
CAUTION Lift the hood by grasping the outside
edges of the inlet opening of the hood. Do not lift the
hood by the exhaust opening divider—damage will
occur! ■Removetheshippingscrewsholdingthewood
mounting piece to the back side of the hood.
Set aside the wood mounting piece and screws for
later installation. Do not discard.
■Removethe“V”shapedcartoninsert.
■Removethepartspackagefromthe“V”shaped
cardboard insert.
■Removethejunctionboxcoverandknockout.
■Installthestrainreliefontothebackortopofthehood.
■Removealltapeandpackingmaterialfromthehood,
duct transition and motor.
1” = 2.5 cm; 1’ = 0.3 m

49-80152 Rev. 8 9
Installation Preparation
PARTS PROVIDED
Locate the parts packed with the hood.
761Dia17
2StainlessSteelGreaseFilters
(3filterswith48"models)
AllenWrench
ForImplementRods
Duct Transition
with Damper
2GreaseFilterTrays
(3supportswith48"models.)
2 Implement Rods and 4 Stand-offs
Heat Lamp
(2with48"models)
490Dia57
761Dia30
490Dia66
WoodSupport
with Original Screws
761Dia28
HARDWARE PACKAGE
Locate and check contents. Screws
shown actual size.
6Phillipsheadscrewsto
secure hood to the wood
support:(2securedto
wood support)
4Phillipsheadscrewsto
secure the transition to the
hood outlet on the top
2(3/16")hollowwallanchors
with screws to secure hood to
the wall at the bottom 4 screws to secure the wood
support to the wall
POZIDRIV3
1 safety screw and lock
washer,tosecuretheblower:
(screw is marked with red or
blue paint)
658Dia9
2 flat washers
for wall anchors
761Dia68
1” = 2.5 cm; 1’ = 0.3 m

10 49-80152 Rev. 8
Installation Instructions
1DETERMINE HOOD, DUCTWORK AND WIRING LOCATIONS
■Usealeveltodrawthecooktopcenterlinelocation.
Draw the line to ceiling height.
■Measuredesireddistancefromthebottomofthehood
tothecookingsurface,30”min.to36”max.
NOTE:Ifyouareinstallingthehoodwithductcovers,be
suretoread“Optionalductcoveraccessories”section
foundonpage4.Exactinstallationheightmaybe
determined by use of one or more duct covers.
■Usealeveltodrawastraighthorizontalpencilline
indicating the bottom of the hood.
■Fromthelineindicatingthebottomofthehood,
measure 15-3/8” up and draw another line for the
location of the wood support. See illustration.
FOR VERTICAL (Straight Up) DUCTING
■Usealeveltodrawacenterlinefromthebottomofthe
hood to ceiling or soffit.
■Ifventingouttheceiling,extendthecenterlineforward
on the ceiling or soffit.
■Locatethecenterlineofa10-1/2”holeontheceiling
or soffit by measuring 6” from the wall.
FOR DUCTING THROUGH REAR WALL
■Measure9-7/8"abovethemarkedlineforthetopof
thehood.Atthecenterline,marklocationfora10-1/2"
diameter hole.
NOTE:MinimumceilingheightforREARWALL
EXHAUSTwithductcoversis8'4"wheninstallingat30"
abovecountertopusing10"elbow.
House Wiring Location
■Thejunctionboxisfastenedtothebackofthehood
on the right side.
■Therecessedbacksideofthehoodprovidesalarge
areaforthehousewiringtoexitthewallandberouted
totherearknockoutandjunctionbox.
■Thelocationforthehousewiringdependsonthe
installation height of the hood and the width of the hood.
■Removejunctionboxcoverandknockout.Install
strain relief.
Alternate Knockout Locations
Iftheinstallationrequires,thejunctionboxcanbe
relocated from the back to the top of the hood. Remove
3screws,alignboxtotopknockoutandsecurewith
original screws.
■Removejunctionboxcoverandknockout.Installstrain
relief.
*DependingonHoodwidth
and Installation Height.
18-13/16" for 48" Models
12-13/16" for 36" Models
9-13/16" for 30" Models
Electrical
Area
8-3/8"
6-1/2"
18-1/16" for 48" Models
12-1/16" for 36" Models
9-1/16" for 30" Models
1” = 2.5 cm; 1’ = 0.3 m

49-80152 Rev. 8 11
Installation Instructions
2A INSTALL HOOD ONTO WALL
SKIP THIS STEP IF INSTALLING BENEATH A
SOFFIT OR CABINET, GO TO STEP 2B.
■Locateatleast2verticalstudsatthewoodsupport.
■Centerthesuppliedwoodsupport,lefttorightand
belowthe15-3/8"markedline.
■Securethewoodsupportto2ormoreverticalstuds,
using at least 2 of the 4 supplied long screws.
IMPORTANT:Screwsmustpenetrateatleast1-1/2"into
vertical studs. Countersink screws into support.
NOTE: The mounting screws must remain in their
original shipping location. These screws are positioned
to engage the keyhole slots in the back of the hood.
■Adjustdepthoforiginalmountingscrewsinthewood
supportuntiltheyprotrude1/4"forward.This1/4"gap
will provide clearance to hang the hood.
IMPORTANT:Framingmustbecapableof
supporting up to 150 lbs.
Install Transition Onto Top of Hood
IMPORTANT: Remove
shipping tape from damper
and check that damper
moves freely.
■Placethetransitionpiece
overthehoodexhaust
and secure with 4 screws
provided.
■Useducttapetosealtheconnection.Checktobe
sure the damper moves freely.
Hang Hood On Wood Support
■Liftthehoodandholdclosetotheinstallationlocation.
Route house wiring through the knockout and into the
junctionbox.
■Placethehoodoverthewoodsupport.Besurethe
mounting screws engage the keyhole slots in the back
of the hood. Tighten the screws.
WARNING
Continue to provide additional support
while the hood is mounted with only these 2 screws.
These screws will not support the weight of the hood. The
hood could fall resulting in damage or personal injury.
■Checktobesure
the hood is level and
centered.
Test Duct Cover Fit
■Placeductcover(s)
over the top of the
hood to check for gaps.
Adjustthehoodupor
down if necessary.
Install Bottom
Mounting Screws
■Drill1/8"pilotholesintothetwolowermounting
holes. Enlarge the holes if they did not enter studs
to3/8".Insertanchorsforwallfastenersintobottom
holes. Remove anchor screws and add flat washers
provided. Drive screws into anchors and tighten.
■Install4additionalscrewsthroughthebackofthe
hood and into the wood support.
Duct
Transition
Top of
Hood
Centerline of
Installation
Space
15-3/8"
30"
to
36"
Wood
Support
1/4"
Gap
Original Mounting
Screws as Shipped
Centerline of
Installation
Space
30"
to
36"
1” = 2.5 cm; 1’ = 0.3 m

12 49-80152 Rev. 8
Installation Instructions
2B Alternate Mounting Method
INSTALL HOOD TO SOFFIT OR
BENEATH CABINETS
SKIP THIS STEP IF USING WALL MOUNTING
METHOD
Whennecessary,thehoodmaybeinstalledsothatitis
supported by the soffit.
■Thesoffitshouldbeconstructedwith2x4’s.
■Determinetheinstallationlocationonthewall.
■Continuethecenterlineforwardonthebottomofthe
cabinet or soffit.
■Theopeningabovethehoodshouldallowforthe
10"roundductandclearancetoslidethehoodback
against the wall.
■The2x4studsmustbelocatedasshowninthe
chart,Dim.A.toacceptmountingscrews.
■Drill1/8"pilotholesintothestudsatthelocations
shown in the top view illustration.
IMPORTANT: Soffit framing must be capable of
supporting up to 150 lbs.
Install Transition Onto Top of Hood
IMPORTANT: Remove
shipping tape from damper
and check that damper
moves freely.
■Placethetransitionpiece
overthehoodexhaust
and secure with 4 screws
provided.
■Useducttapetosealtheconnection.Checktobe
sure the damper moves freely.
Mount Hood onto Soffit or Cabinet
NOTE: If mounting to the underside of a cabinet with a
recessedbottom,installshimstofillthegap.
■Drivemountingscrewsintothestudsuntilthey
protrude1/4".The1/4"gapwillprovideclearanceto
engage the keyhole slots in the top of the hood.
■Lifthoodtoinstallationposition.Locatehousewiring
and route through the knockout (from the back or top
of the hood).
■Lifthoodontomountingscrews.Slidebackagainstthe
rear wall.
■Tightenmountingscrews.
IMPORTANT:Foradditionalsupportandto
minimizevibrationduringoperation,thehoodmust
be secured to the back wall. Use wall anchors to
fasten bottom back of hood to the wall.
A
Requires 10-1/2" Min.
Opening For Ductwork
and Hood Installation
A
Duct
Transition
Top of
Hood
“A” Centerline to Stud
and Keyhole Slots
“B” Hood Width At
the Top
ZV48T 19-9/16" 40"
ZV48S 23-9/16" 47-15/16"
ZV36T 13-9/16" 28"
ZV36S 17-9/16" 35-15/16"
ZV30T 10-9/16" 22"
ZV30S 14-9/16" 29-15/16"
2"
7-1/2"
A
B
2-9/16"
8"
8-1/8"
6"
Back of Hood
Top View
Front of Hood
1/4" Gap
Push Back
to Wall
Add Shims
If Bottom
Is Recessed
Back
Wall
Cabinet
or
Soffit
Engage Top
Keyhole Slots
1” = 2.5 cm; 1’ = 0.3 m

49-80152 Rev. 8 13
Installation Instructions
3CONNECT DUCTWORK
■Installductwork,makingconnectionsindirectionof
airflow as illustrated.
■Securejointsinductworkwithsheetmetalscrews.
■Wrapallductjoints
with duct tape for an
airtight seal.
■Useducttapeto
seal the flange
connection. Reach
inside the hood and
push the damper up
to be sure it moves
freely.
5INSTALL DUCT COVERS
NOTE: Foreasierhandling,removecardboardinsert
after film is peeled off.
Remove protective film from duct covers. If more than
oneductcoverisused,secureeachpiecetogether
with screws provided.
■Placetheductcover(s)ontopofthehood.
■Frominsidethehood,securetheductcovertothe
topwiththesmallPhillipsheadscrewssupplied
with the covers.
6INSTALL MOTOR
■Fromtheinsideofthehood,slipmotorintothe
attachment slot on the left.
■Rotatemotorupwardsuntilitsnapsintothespring
clip on the right.
■Securethemotortothehoodwiththemachine
screw and lock washer. (Screw is marked with red
or blue paint.)
■Plugconnectorintothemotor.
IMPORTANT: Connector ends are designed to mate
only one way. Match flat and round connectors as
shown.
4CONNECT ELECTRICAL
Verify that power is turned off at the source.
WARNING If house wiring is not 2-wire with
agroundwire,agroundmustbeprovidedbythe
installer.Whenhousewiringisaluminum,besure
touseU.L.approvedanti-oxidantcompoundand
aluminum-to-copper connectors.
■Usewirenutstoconnectincominggroundtogreen,
white to white and black to black.
■Pushwiresintojunctionboxandreplacecover.Be
sure wires are not pinched.
Screw
Duct Tape
Over Seam
and Screw
Air Flow
Duct Tape
Over Transition
White
Ground Black
Remove
Junction Box
Cover
Insert Power
Conduit Thru
Strain Relief
and Tighten
Use UL Listed
Wire Nuts
AB
C
Top
Attachment
Screw
Spring
Clip
Spring
Clip
Outlet
Attachment
Slot
1” = 2.5 cm; 1’ = 0.3 m

14 49-80152 Rev. 8
Installation Instructions
7INSTALL FILTERS
■Placefilterdriptraysintotherearofthehood.
■Insertthegreasefilterintotheopeninganddrop
into the trays.
■Toremovethefilters,graspthehandle,pushthe
filter up and lift out.
8INSTALL IMPLEMENT RODS
■Useaflatbladescrewdrivertoinstallthestand-offs
into the bottom of the hood.
■Aligntheimplementrodtothestand-offswiththe
screw hole towards the inside of the hood. Secure the
rodtothestand-offswiththesuppliedAllenwrench.
■Followthesameprocedureontheoppositeside.
FINALIZE INSTALLATION
■Installthesuppliedinfraredbulb(s).
■SeetheOwner’sManualforinstructionstotest
operation.
761Dia26
761Dia27
Screw
Stand-offs
Into
Hood
Use Allen
Wrench to
Secure Rod
to Stand-offs
1” = 2.5 cm; 1’ = 0.3 m

49-80152 Rev. 8 15
Notes

NOTE:Whileperforminginstallationsdescribedinthis
book,safetyglassesorgogglesshouldbeworn.
ForMonogram®localserviceinyourarea,call
1.800.444.1845.
NOTE:Productimprovementisacontinuingendeavor
atGEAppliances.Therefore,materials,appearance
and specifications are subject to change without notice.
49-80151Rev.9
05-19GEA
PrintedinMexico

INSTRUCTIONS
D'INSTALLATION
Hottes professionnelles de 30po,
36po et 48po
Monogram.com
TOUT ÉLEVER

249-80152 Rév. 8
Consignes de sécurité
LISEZ ET CONSERVEZ CES INSTRUCTIONS
AVANT DE COMMENCER
Lisez attentivement toutes ces instructions.
■IMPORTANT – Conservez ces instructions
pour l'inspecteur local.
■IMPORTANT –Respectez tous les codes et
règlements en vigueur.
■Remarque destinée à l'installateur – Assurez-vous de
laisser ces instructions au consommateur.
■Remarque destinée au consommateur – Conservez
ces instructions avec votre Manuel de l'utilisateur pour
vous y reporter ultérieurement.
■Niveau de compétence – L'installation de cet appareil
nécessite des compétences de base en mécanique et
en électricité.
■Durée de l'installation – 1 à 3 heures
■L'installateurestresponsabledelaqualitédel'installation.
La panne du produit due à une mauvaise installation n'est
pas couverte par la garantie.
■PourleserviceàlaclientèleMonogramdansvotre
région, appelez le 1-800-444-1845.
■PourleserviceàlaclientèleMonogramauCanada,
appelez le 1-800-561-3344.
■PourlespiècesetaccessoiresMonogram,appelezle
1-800-626-2002.
ATTENTION Compte tenu du poids et de la dimension
de ces hottes, et afin de réduire les risques de blessure et
pour ne pas endommager le produit, LEUR INSTALLATION
DOIT ÊTRE EFFECTUÉE PAR DEUX PERSONNES.
AVERTISSEMENT
Pourréduirelesrisquesd'incendieoude
décharge électrique, n'utilisez pas cette hotte de cuisinière
avec un dispositif de contrôle de vitesse à semi-conducteurs
externe. Toute modification de ce type au câblage d'origine
de l'usine pourrait endommager l'appareil et/ou créer un
risque pour la sécurité électrique.
POUR RÉDUIRE LES RISQUES D'INCENDIE, UTILISEZ
UNIQUEMENT DES CONDUITS MÉTALLIQUES.
AVERTISSEMENT
POUR DIMINUER LES RISQUES
D'INCENDIE, DE DÉCHARCHE ÉLECTRIQUE OU DE
BLESSURES, SUIVEZ LES CONSIGNES SUIVANTES :
A. Cet appareil doit uniquement être utilisé aux fins prévues
par son fabricant. Si vous avez des questions, contactez
le fabricant.
B. Avant de réparer ou de nettoyer l'appareil, coupez
l'alimentation au tableau de distribution et bloquez
le disjoncteur pour éviter que le courant ne soit
accidentellement rétabli. S'il n'est pas possible de bloquer
le disjoncteur, posez un avertissement bien visible,
comme une étiquette, sur le tableau de distribution.
ATTENTION
POURUNEUTILISATIONDE
VENTILATIONGÉNÉRALEUNIQUEMENT.NEPASUTILISER
POURÉVACUERDESMATIÈRESDANGEREUSES,DES
MATIÈRESEXPLOSIVESOUDESVAPEURS.
AVERTISSEMENT
POURDIMINUERLESRISQUES
D'INCENDIE, DE DÉCHARCHE ÉLECTRIQUE OU DE
BLESSURES, SUIVEZ LES CONSIGNES SUIVANTES :
■L'installation et le câblage électrique doivent être effectués
par une personne qualifiée et conformément à tous les codes
et toutes les normes applicables, incluant les règlements
concernant les constructions classées résistantes au feu.
■Unequantitéd'airsuffisanteestnécessaireàune
combustion et à une évacuation appropriées des gaz
par le conduit d'évacuation (cheminée) de l'équipement
à combustible pour éviter tout refoulement. Suivez
les instructions et normes de sécurité du fabricant de
l'appareil chauffant, comme celles publiées par la National
FireProtectionAssociation(NFPA),l'AmericanSociety
for Heating, Refrigeration and Air Conditioning Engineers
(ASHRAE) et les autorités locales. Le cas échéant,
installez un système d'air d'appoint (de remplacement)
conformément aux exigences du code du bâtiment local.
Visitez le site electromenagersge.ca pour connaître les
solutions d'air d'appoint offertes.
■Lorsquevouseffectuezdesdécoupesouquevouspercez
dans des murs ou des plafonds, n'endommagez pas le
câblage électrique ou les installations des services publics.
■Lessystèmesquidisposentdeconduitsd'aération
doivent toujours être évacués vers l'extérieur.
■ Lescodeslocauxpeuventvarier.L'installation,lesconnexions
électriques et la mise à la terre doivent se conformer aux
codes applicables. En l'absence de codes locaux, la hotte doit
être installée conformément au Code national de l'électricité
ANSI/NFPA70-1990ouàladernièreédition.
ATTENTION
Pourréduirelesrisquesd'incendieet
permettre une évacuation de l'air vers l'extérieur adéquate,
assurez-vous d'acheminer les conduits vers l'extérieur. N'évacuez
pas l'air dans des espaces intra-muraux, dans le plafond, dans le
grenier, dans un vide sanitaire ou dans le garage.

49-80152 Rév. 8 3
Instructions d'installation
TABLE DES MATIÈRES
Consignes de sécurité............................................................. 2
Dimensions du produit............................................................. 3
Dégagements pour l'installation .............................................. 4
Cache-conduits en option........................................................ 4
Déterminer la hauteur d'installation et les cache-conduits...... 5
Planificationpréliminaire ......................................................... 6
Alimentation électrique............................................................ 6
Raccords de conduit................................................................ 7
Outils et matériel nécessaires................................................. 8
Déballage ................................................................................ 8
Piècesfournies........................................................................ 9
Étape 1 : Déterminer les emplacements d'installation
des conduits et du câblage ................................................. 10
Étape 2A : Installer la hotte sur le mur.................................. 11
Étape 2B : Installer la hotte sous une retombée de plafond. 12
Étape 3 : Raccorder le conduit.............................................. 13
Étape 4 : Brancher l'appareil à l'alimentation électrique ....... 13
Étape 5 : Installer les cache-conduits ................................... 13
Étape 6 : Installer le moteur.................................................. 13
Étape7:Installerlesfiltres................................................... 14
Étape 8 : Installer les tiges d'ustensiles................................ 14
DIMENSIONS DU PRODUIT
Modèle ZV48S avec côtés droits
Modèle ZV36S avec côtés droits
Modèle ZV30S avec côtés droits
Modèle ZV48T avec côtés coniques
Modèle ZV36T avec côtés coniques
Modèle ZV30T avec côtés coniques
18 po
40 po
25 po 47-15/16 po
12 po
18 po
47-15/16 po
47-15/16 po
12 po
25 po
18 po
35-15/16 po
35-15/16 po
12 po
25 po
18 po
28 po
25 po 35-15/16 po
12 po
18 po
29-15/16 po
29-15/16 po
12 po
25 po
18 po
22 po
25 po 29-15/16 po
12 po
1 po = 2,5 cm; 1 pi = 0,3 m

449-80152 Rév. 8
Préparatifs
DÉGAGEMENTS POUR L'INSTALLATION
Ces hottes sont conçues pour être installées sur un mur ou
sous une retombée de plafond ou une armoire.
■Installezceshottesàaumoins30poetàauplus36po
de la surface de cuisson.
■Ceshottespeuventêtreinstalléesàunedistance
minimale de 24 po au-dessus d'une surface de cuisson
au gaz ou électrique de style encastrable. Respectez
toujours le dégagement de 30 à 36 po lorsqu'elles sont
installées au-dessus d'une surface de cuisson ou d'une
cuisinière de type professionnel.
REMARQUE : Les espaces de dégagement peuvent
varier en fonction du type de hotte et des codes
locaux. Vérifiez auprès des inspecteurs locaux pour
vous assurer que la norme est applicable.
Pourcetteinstallation,leconduitd'évacuationdelapartie
supérieure de la hotte sera dissimulé dans la retombée de
plafond ou dans l'armoire supérieure.
Pourcetteinstallation,uncache-conduitdécoratifpermetde
dissimuler le conduit d'évacuation de la partie supérieure de
la hotte. L'utilisation d'un cache-conduit décoratif exige des
hauteurs d'installation spécifiques au-dessus du comptoir.
CACHE-CONDUITS EN OPTION
Les cache-conduits décoratifs standard sont disponibles en
hauteurs de 6 po et 12 po. Les cache-conduits peuvent être
superposés dans diverses combinaisons, pour dissimuler
les conduits du haut de la hotte jusqu'au plafond.
■Avantdecommencer,vousdevezdéterminerlahauteur
d'installation de la hotte et commander le cache-conduit
de la bonne grandeur. Les cache-conduits doivent être
commandés en même temps que la hotte et être sur
place avant l'installation. Commandez le cache-conduit
correspondant au modèle de votre hotte.
Cache-conduit
de 6 po
Cache-conduit
de 12 po
Cache-conduits standard
Cache-conduits de 6 po
Modèle de
la hotte
Cache-conduit
de 6 po Dimensions
ZV48T,
ZV48S
ZX48DC6 H6poxL19-11/16poxP11-7/8po
ZV36T,
ZV36S
ZX36DC6 H6poxL15-3/4poxP11-7/8po
ZV30T,
ZV30S
ZX36DC6 H6poxL15-3/4poxP11-7/8po
Cache-conduits de 12 po
Modèle de
la hotte
Cache-conduit
de 12 po Dimensions
ZV48T,
ZV48S
ZX48DC12 H12poxL19-11/16poxP11-7/8po
ZV36T,
ZV36S
ZX36DC12 H12poxL15-3/4poxP11-7/8po
ZV30T,
ZV30S
ZX36DC12 H12poxL15-3/4poxP11-7/8po
RETOMBÉE DE PLAFOND
Installation sur retombée de plafond
30 po MIN.
36 po MAX.
Installation murale
30 po MIN.
36 po MAX.
1 po = 2,5 cm; 1 pi = 0,3 m