Monoprice Monolith 7X User manual

Monolith 7X 7-Channel 200-Watt Power Amplifier
Model 14566
User's Manual

2
CONTENTS
SAFETY WARNINGS AND GUIDELINES.......................................................................................................................................3
INTRODUCTION................................................................................................................................................................................................4
FEATURES..............................................................................................................................................................................................................4
CUSTOMER SERVICE....................................................................................................................................................................................5
PACKAGE CONTENTS.................................................................................................................................................................................5
PRODUCT OVERVIEW.................................................................................................................................................................................6
CABLE PREPARATION................................................................................................................................................................................. 7
Speaker Wires............................................................................................................................................................................................. 7
RCA Cables.....................................................................................................................................................................................................8
Trigger Cables .............................................................................................................................................................................................8
REMOTE POWER ON....................................................................................................................................................................................8
INSTALLATION..................................................................................................................................................................................................9
MAIN CIRCUIT BREAKER ........................................................................................................................................................................10
PROTECTION CIRCUITRY........................................................................................................................................................................10
TROUBLESHOOTING ...................................................................................................................................................................................11
TECHNICAL SUPPORT................................................................................................................................................................................11
SPECIFICATIONS............................................................................................................................................................................................12
REGULATORY COMPLIANCE.........................................................................................Error! Bookmark not defined.
Notice for FCC .....................................................................................................................Error! Bookmark not defined.
Notice for Industry Canada......................................................................................Error! Bookmark not defined.

3
SAFETY WARNINGS AND GUIDELINES
This device is intended for indoor use only.
Do not expose this device to water or moisture of any kind. Do not place drinks or
other containers with moisture on or near the device. If moisture does get in or on
the device, immediately unplug it from the power outlet and allow it to fully dry
before reapplying power.
Do not touch the device, the power cord, or any other connected cables with wet
hands.
Do not expose this device to excessively high temperatures. Do not place it in, on,
or near heat sources, such as a fireplace, stove, radiator, etc. Do not leave it in direct
sunlight.
This device ventilates excessive heat through the slots and openings in the case. Do
not block or cover these openings. Ensure that the device is in an open area where
it can get sufficient airflow to keep from overheating.
Do not place or install this device in an area where it can be exposed to excessive
amounts of dust, humidity, oil, smoke, or combustible vapors.
Prior to operation, check the unit and power cord for physical damage. Do not use if
physical damage has occurred.
Take care to prevent damage to the power cord. Do not allow it to become
crimped, pinched, walked on, or become tangled with other cords. Ensure that the
power cord does not present a tripping hazard.
Before plugging the unit into a power outlet, ensure that the outlet provides the
same type and level of power required by the device.
This device uses a grounded power cord and requires a ground connection for safe
operation. Ensure that the power source has a proper ground connection. Do not
modify the plug or use a "cheater" plug to bypass the ground connection.
Ensure that power is turned off and disconnected before making any electrical
connections.

4
Do not plug this device into the switched output of a preamplifier or other audio
component. This amplifier requires higher current levels than these devices are
designed to handle.
Unplug this device from the power source when not in use.
Never unplug the unit by pulling on the power cord. Always grasp the connector
head or adapter body.
Clean using a soft, dry cloth only. Do not use chemical cleaners, solvents, or
detergents. For stubborn deposits, moisten the cloth with warm water.
This device has no user serviceable parts. Do not attempt to open, service, or
modify this device.
INTRODUCTION
Thank you for purchasing this Monolith 7-Channel 200-Watt Power Amplifier!
This power amplifier features seven independent channels, each capable of delivering
more than 200 watts of power into 8 ohm loads. A trigger input jack allows for remote
power on/power off when a source device is powered on. Each channel features an
optically coupled protection circuit, to prevent damage to the amplifier or speakers.
FEATURES
Seven independent 200-watt into 8 ohms amplifier modules
20Hz ~ 20kHz ±0.1dB frequency response
Gold plated RCA input and speaker output connectors
Remote power-on trigger option
Rated for 4 ~ 16 ohm loads
Optically coupled short circuit protection

5
CUSTOMER SERVICE
The Monoprice Customer Service department is dedicated to ensuring that your ordering,
purchasing, and delivery experience is second to none. If you have any problem with your
order, please give us an opportunity to make it right. You can contact a Monoprice
Customer Service representative through the Live Chat link on our website
www.monoprice.com during normal business hours (Mon-Fri: 5am-7pm PT, Sat-Sun: 9am-
6pm PT) or via email at [email protected]
PACKAGE CONTENTS
Please take an inventory of the package contents to ensure you have all the items listed
below. If anything is missing or damaged, please contact Monoprice Customer Service for a
replacement.
1x Monolith 7x 200-watt power amplifier
1x AC power cord (NEMA 5-15 to IEC 60320 C19)
1x User's manual

6
PRODUCT OVERVIEW
A. INPUT 1-7: RCA and XLR line-level inputs for connection to the preamplifier outputs
on a dedicated preamplifier or AV receiver. The Input Select switch switches
between the RCA and XLR inputs.
B. TRIGGER INPUT: 3.5mm TS jack for connection to the trigger output of a source
device. The presence of voltage on this input will cause the amplifier to power on.
The amplifier will automatically power down into standby mode after the trigger
signal has been removed.
C. OUTPUT 1-7: Paired 5-way binding posts for connecting the speakers.
D. POWER INPUT: The IEC 60320 C20 panel connector connects to the included high-
current AC power cable.
E. MASTER POWER: The Master Power switch is used to apply or remove power to the
amplifier. By contrast, the Power switch on the front panel is used to switch the
amplifier between standby mode and full power on.
F. GND: Chassis ground. While a grounding wire is rarely needed, occasionally there is
a hum issue when components are interconnected. This can be remedied by tying
their chassis grounds together.
POWER SWITCH (Front Panel, not pictured): Switches the amplifier between
standby mode and full power on.

7
CABLE PREPARATION
You will need several cables for this installation. None of the cables or connectors
mentioned in this section are included with the system.
Important Safety Note! If you plan on running any of these cables through the walls,
through a connecting floor, or inside an air duct, they should be rated for In-Wall, Riser
(between floors), or Plenum (air duct) use in commercial installations. For residential
installations, an In-Wall rating is sufficient for all circumstances. Using unrated or
improperly rated cables could accelerate the spread of any fire and could nullify insurance
claims.
Speaker Wires
You will need seven speaker wires to connect each speaker to the amplifier. The size
(AWG) of wire you choose depends on the distance from the amplifier to the speakers, the
speaker impedance, and the physical limits of the terminals at each end.
Other than saving a few pennies of cost or grams of weight per foot, there is no reason to
use anything other than the thickest wire possible. This amplifier uses 5-way binding post
connectors, which can accept bare wire, spade lugs, banana plugs, and pin plugs. For
anything other than extremely short speaker wire runs, you should use at least 14AWG
wire, but preferably 12AWG or 10AWG, depending on which gauges your speakers can
accept.
Whichever speaker wire you get, make sure that it has marks to identify one conductor
from another. Most speaker wire uses a colored stripe to identify one of the conductors.
The identified conductor is usually used for the positive (+/red) connection and the other
for the negative (-/black) side.
Note: When cutting speaker wire, ensure that the length of each stereo pair is the same.
This ensures that the overall impedance of each paired channel is identical. If there is any
excess speaker wire, it should not be coiled, as it could create an antenna to receive stray
radio signals. Instead, snake the excess wire back and forth.

8
RCA or XLR Cables
You will need seven single RCA or XLR cables to connect the preamp outputs on your
preamplifier to the inputs on this amplifier. In most cases, ordinary RCA cables are
sufficient. However, if there is a significant distance between the amplifier and the
preamplifier, it is recommended to use RCA cables manufactured using shielded RG6 or
RG59 cable. For long distance cable runs, balanced XLR cables are highly recommended.
Trigger Cables
This amplifier features a low voltage trigger input, which can switch the amplifier from
standby mode into full power on mode whenever the trigger signal is detected. The trigger
signal consists of a low-current, low-voltage signal (between 3.3 and 24 VDC) applied to
the input, which is carried between components with a cable that terminates in a 3.5mm
TS plug.
REMOTE POWER ON
This amplifier features a trigger input, which is used to switch the amplifier between
standby mode and full power on mode. The input is a 3.5mm TS jack that accepts a voltage
level from 3.3 to 24 VDC. Some source devices feature a trigger output, which can be used
to trigger the amp.
If your source device does not contain a trigger output, but does have a switched AC
outlet, you can obtain a trigger adapter, which consists of an AC adapter with a 3.5mm TS
plug on the end of the cord. This adapter can then provide the necessary trigger signal
whenever the component it is plugged into is turned on.
To use the amplifier with remote power on, the Master Power switch on the rear panel
should be in the ON position and the Power switch on the front panel in the Standby
position.
To override the remote power on feature or to use the amp without it, simply use the
Power switch on the front panel to turn the amp on and off (standby).

9
INSTALLATION
Perform the following steps to install this amplifier into a 7.1-channel audio system.
1. Power off and unplug all equipment that will be connected to this amplifier.
2. Prepare seven lengths of speaker wire (not included) to connect each of the seven
output channels to its respective speaker.
3. Using a two-conductor speaker wire, connect one end to the input terminals on the
speaker, then connect the other end to the Output terminals on the amplifier. Take
care to maintain polarity with positive to positive and negative to negative.
4. Repeat step 3 for each of the other six speakers.
5. Using a single RCA interconnect cable (not included), plug one end into the Input on
the amplifier, then plug the other end into the preamplifier output of the same
name.
Example: Connect the Center channel input on the amplifier to the Center channel
output on the preamplifier.
6. Repeat step 5 for each of the other six channels.
7. (Optional) Using a two-conductor 3.5mm TS cable (not included), plug one end into
the Trigger Input on the amplifier, then plug the other end into the trigger output
on your source device.
8. Ensure that the Master Power switch is in the OFF position and that the Power
switch is in the Standby position.
9. Using the included AC power cable, plug the C19 connector on the cable into the
C20 panel connector on the amplifier, then plug the other end into a nearby AC
power source.
Warning! Do not plug the amplifier into a switched outlet on a preamplifier or other
audio component. The amplifier should be plugged directly into an AC wall outlet.
10. Ensure that the volume on the preamplifier is set to the minimum level.
11. Power on all equipment connected to the amplifier, then press the Master Power
button on the amp to power it ON. The power button LED will blink until the

10
circuitry is properly warmed up. Once the LED stops blinking and illuminates
steadily, the amplifier has finished the start-up process and is ready for operation.
Note: It is recommended to always turn the amplifier on last and to turn it off first
whenever powering your audio system on or off. This ensures that any pops or
transient spikes, which could cause damage to the delicate speaker coils, are not
sent to your speakers.
Congratulations, your amplifier is connected and ready for use!
MAIN CIRCUIT BREAKER
The Master Power switch on the rear panel doubles as a circuit breaker. If the circuit
breaker trips into the off position, try flipping it back on. If it immediately trips back off,
unplug the amplifier from the power source and have it serviced.
PROTECTION CIRCUITRY
If the amplifier senses a short on one of the speaker wires the built-in protection circuit will
cut off audio output. The circuit will continue to monitor the line and will stay cut off as
long as the short continues to exist. If this occurs, inspect the speaker wire connections at
each end and fix any shorts that exist. Once the short is repaired, the amplifier will
continue to operate as normal.

11
TROUBLESHOOTING
Q1. The amplifier will not power on.
A1. Verify that the Master Power switch on the rear panel is in the ON position. Check to
ensure that the AC power cord is fully plugged in at each end. Verify that the AC
power outlet is live by plugging in another device, such as a lamp.
Q2. Audio from some channels, but not others.
A2. Try swapping the speaker from a good channel to the output of the bad channel to
see if the problem is with the input or output. Check that the RCA input cable is firmly
seated on the connector at each end. Try swapping out the input RCA cable with a
known good cable. Check the speaker wire connections at each end. Try swapping out
the speaker wire with a known good one.
Q3: Audio plays, then cuts off.
A3: Check the speaker wire connections for stray wire strands, which could cause a short
circuit.
TECHNICAL SUPPORT
Monoprice is pleased to provide free, live, online technical support to assist you with any
questions you may have about installation, setup, troubleshooting, or product
recommendations. If you ever need assistance with your new product, please come online
to talk to one of our friendly and knowledgeable Tech Support Associates. Technical
support is available through the online chat button on our website www.monoprice.com
during regular business hours, 7 days a week. You can also get assistance through email by
sending a message to [e-mail]

12
SPECIFICATIONS
Model
14566
Number of Channels
7
EIA 1kHz Output Power at 8 Ohms*
250 watts
EIA 1kHz Output Power at 4 Ohms*
375 watts
FTC Full Bandwidth Output Power
at 8 Ohms**
200 watts
FTC Full Bandwidth Output Power
at 4 Ohms**
300 watts
Input Sensitivity for Full Rated Power
RCA Input: 1.49 Volts
XLR Input: 1.67 Volts
Frequency Response at Rated Output
20Hz ~ 20kHz ±0.1dB
Phase Response
+5 to -15 degrees from 20Hz to 20kHz at 1 watt
Signal-to-Noise Ratio "A-Weighted"
Greater than 110dB below rated FTC Full
Bandwidth Power
Total Harmonic Distortion (THD)
Less than 0.03% at full rated FTC power
Less than 0.005% at full EIA power at 1kHz
Intermodulation Distortion (IMD)
Less than 0.03% at full rated FTC power
Less than 0.005% at full EIA power at 1kHz
Load Impedance
Safe with all types of loads
Rated for 4 to 16 ohms
Power Bandwidth
FTC +0-3db from 5Hz ~ 100kHz
Damping Factor
Greater than 400 from 10Hz ~ 400Hz
Crosstalk
Greater than –100dB from 20Hz ~ 20kHz
Gain
Voltage gain of +28dB (XLR) or +28.5dB (RCA)
Slew Rate
> 50V/µs

13
Input Impedance
28 kilohms (nominal)
Remote Trigger Voltage
3.3 ~ 24 VDC at 5mA or greater
DC Output Offset
Less than ±5mV
Input Power
120 VAC (nominal)
Chassis Dimensions
17.0" x 7.0" x 16.5" (432 x 178 x 419 mm)
Net Weight
93.2 lbs. (42.3kg)
* EIA 1kHz Power refers to maximum average power in watts RMS at 1kHz with 1% THD +N.
This test is performed with one channel at this maximum power with all other channels
driven to 1/8th power.
** FTC Full Bandwidth Power refers to maximum average power in watts RMS from 20Hz to
20kHz with 0.03% THD+N. This test is performed with all channels driven to full power.