Monoprice 5754 User manual

INSTALLATION INSTRUCTIONS
Under-cabinet / Ceiling Mount
PID 5754
ISSUED: NOV. 2012
CAUTION: DO NOT EXCEED MAXIMUM
LISTED WEIGHT CAPACITY. SERIOUS
INJURY OR PROPERTY DAMAGE MAY
OCCUR!
7
8kg8kg
(17.6lbs)(17.6lbs)
MAXMAX
8kg
(17.6lbs)
MAX
23″
MAX
50x50
75x75
100x100
5. Adjustment
Maintenance
• Check that the bracket is secure and safe to use at regular intervals(at least every three months).
• Please contact your dealer if you have any questions.
For saving the space, you can fold display by pushing display back until it fits in place.
Adjust to desired location.
4. Attach the Display to the VESA Plate
TV
TV
TV
M-C
M-A
M-B
Tighten all screws but do not over tighten.
Lift the display and match the holes on your display with the
hole on the mount. Secure your display to the mount by
tightening screws.
B
0°~-110°
360°

21
NOTE: Read the entire instruction manual before you start installation and assembly.
WARNING
• Do not begin the installation until you have read and understood the instructions
and warnings contained in this installation sheet. If you have any question
regarding any of the instruction or warning, please contact your local distributor.
• This mounting bracket was designed to be installed and utilized ONLY as
specified in this manual. Improper installation of this product may cause damage
or serious injury.
• This product should only be installed by someone of good mechanical ability,
with basic building experiences and fully understanding of this manual.
• Make sure that the supporting surface will safely support the combined load of
the equipment and all attached hardware and components.
• Always use assistant or mechanical lifting equipment to safely lift and position
equipment.
• Tighten screws firmly, but do not over tighten. Over tightening can damage the
items, greatly reducing their holding power.
• This product is intended for indoor use only. Using this product outdoors could
lead to product failure and personal injury.
Package W
D5 washer (x4)
M-C
M5x14 (x4)
M-B
M4x14 (x4)
M-A
Component Checklist
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installing. If
any parts are missing or faulty, telephone your local distributor for a replacement.
Package M
ceiling mount (x1)
A
concrete anchor (x6)
W-B
ST5.5x50 (x6)
W-A
5mm Allen key (x1)
B

1
Find and mark the
exact location of
mounting holes.
3a. Mount on Wooden Ceiling
ø 4mm
(ø 5/32”)
50mm
(2”)
50mm
(2”)
Screw the screws
into the ceiling
Drill pilot holes
2
34
Tighten the screws spacing
3mm to ceiling.
W-A
WARNING
• Installers are responsible to provide hardware for other types of mounting situations.
• Installers must verify that the supporting surface will safely support the combined load of the
equipment and all attached hardware and components.
Align both holes of ceiling plate to screws
in ceiling and move the ceiling plate until
both screws are seated in small area of
tear-drop mounting holes.
Fix the ceiling plate using the four other screws and then tighten all screws.
3mm
W-A

Screw the screws
into the ceiling
Drill pilot holes
1
2
Mark the exact
location of
mounting holes
3b. Mount on Solid Brick and Concrete Block
65
W-B
W-A
Tighten the screws spacing
3mm to ceiling.
60mm
(2.4")
55mm
(2.2”)
ø 8mm
(ø 5/16”)
• When installing ceiling mounts on cinder block, verify the actual concrete thickness is at least
1-3/8" (35mm) for using the concrete anchors. Do not drill into mortar joints! Be sure to
mount in a solid part of the block, generally 1" (25mm) minimum from the side of the block.
It is suggested electric drill on slow setting is used to drill the hole instead of a hammer drill
to avoid breaking out the back of the hole when entering a void or cavity.
• Installers must verify that the supporting surface will safely support the combined load of the
equipment and all attached hardware and components.
WARNING
Align both holes of ceiling plate to screws
in ceiling and move the ceiling plate until
both screws are seated in small area of
tear-drop mounting holes.
Fix the ceiling plate using the four other screws and then tighten all screws.
3mm
W-A