Monoprice 9744 User manual

Maintenance
• Check that the bracket is secure and safe to use at regular intervals(at least every three months).
• Please contact your dealer if you have any questions.
11
PID 9744

21
NOTE: Read the entire instruction manual before you start installation and assembly.
WARNING
• Do not begin the installation until you have read and understood the instructions
and warnings contained in this installation sheet. If you have any question
regarding any of the instruction or warning, please contact your local distributor.
• This mounting bracket was designed to be installed and utilized ONLY as
specified in this manual. Improper installation of this product may cause damage
or serious injury.
• This product should only be installed by someone of good mechanical ability,
with basic building experience and fully understanding of this manual.
• Make sure that the supporting surface will safely support the combined load of
the equipment and all attached hardware and components.
• If mounting to wood wall studs, make sure that mounting screws are anchored
into the center of the studs. The use of a stud finder is highly recommended.
• Always use assistant or mechanical lifting equipment to safely lift and position
equipment.
• Tighten screws firmly, but do not over tighten. Over tightening can damage the
items, greatly reducing their holding power.
• This product is intended for indoor use only. Using this product outdoors could
lead to product failure and personal injury.
Component Checklist
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installing. If
any parts are missing or faulty, telephone your local distributor for a replacement.
Package M
Package W
ST6.3x55 (x3)
W-A
concrete anchor (x3)
W-B
D8 washer (x4)
M-F
D5 washer (x4)
M-E
small spacer (x8)
M-G
M5x14 (x4)
M-B
M6x14 (x4)
M-C
M8x20 (x4)
M-D
M4x14 (x4)
M-A
articulated arm assembly
A
4mm Allen key (x1)
B
6mm Allen key (x1)
C
wrench (x1)
D

4
3
2. Remove the Decorative Covers
1. Separate VESA Plate from Wall Mount
2
ø 4.5mm
(ø 3/16")
55mm
(2.2")
55mm
(2.2")
WARNING
• Make sure that mounting screws are anchored into the center of the studs. The use of a stud
finder is highly recommended.
• Installers are responsible to provide hardware for other types of mounting situations.
• Installers must verify that the supporting surface will safely support the combined load of the
equipment and all attached hardware and components.
3a. Mount on Wood Stud Wall
Drill pilot holes
3
Screw the wall
mount onto
the wall
X X
√
W-A
Find and mark the
exact location of
mounting holes
1
· Loosen the upper nut.
· Then remove the lower flat nut.
Remove the VESA plate.
D

65
4. Install Decorative Covers
5. Install VESA Plate
X X
√
3b. Mount on Solid Brick and Concrete Block
Drill pilot holes
1
2
Screw the wall
mount onto
the wall
60mm
(2.4")
60mm
(2.4")
ø 10mm
(ø 3/8")
Mark the exact
location of
mounting holes
Mark the exact
location of
mounting holes
Mark the exact
location of
mounting holes
Top of the TV
W-B
W-A
Installers must verify that the supporting surface will safely support the combined weight of
the equipment and all attached hardware and components.
WARNING

87
Tighten all screws but do not over tighten.
Screw VESA plate onto the TV.
6. Hooking the TV onto the Wall Mount
· Level the TV.
· Place the lower flat nut and tighten both nuts.
Loosen the upper nut leaving
a 4mm space to the VESA plate.
Hooking the TV onto the wall mount
4mm
or
TV
TV
TV
TV
M-A/M-B
M-C/M-D
M-E
M-F
M-D
M-F
M-G
M-G
M-D
M-F
M-G

FOLD 3
DUST
C
A
T
CHER
10
7. Tension Adjust
Please keep the arm level during tension adjustment. Use a proper Allen key to slightly loosen or tighten the
adjustment screw according to the display weight.
If display settles on its own, rotate adjustment screw towards the "+" symbol.
If display rises on its own, rotate adjustment screw towards the "-" symbol.
8. Cable Management
Connect the cables to the display, and press cable cover inward to route
the cables through the space.
Note: Leave slack in the cable for cantilever arm movement. Adjust to the desired position or tilt.
9. Adjustment
9
height adjustable
max335mm
+15°
-15°
180°
180°
180°
+3° -3°
C
Please tighten the socket set screw if the
joints make popping sounds during use.
Tighten the screws untill the display angle is fixed.
B