Monoprice PID 3874 User manual

INSTALLATION MANUAL
ISSUED: FEB. 2013
CAUTION: DO NOT EXCEED RATED
LISTED WEIGHT CAPACITY. SERIOUS
INJURY OR PROPERTY DAMAGE MAY
OCCUR!
Projector Ceiling Mount
10kg
(22lbs)
RATED
10kg
(22lbs)
RATED
Maintenance
• Check that the bracket is secure and safe to use at regular intervals(at least every three months).
• Please contact your dealer if you have any questions.
11
PID 3874
875
009
PID 3
PID 3

21
Component Checklist
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation.
If any parts are missing or faulty, telephone your local distributor for a replacement.
Package M
Package W
ST6.3x50 (x3)
W-A
concrete anchor (x3)
W-B
decorative cover (x1)
B
15cm extension pipe (x1)
E
projector plate (x1)
C
mounting leg (x3)
D
ceiling plate (x1)
A
M4x14
M-A
(x4) M5x20
M-B
(x3) 4mm Allen key (x1)
M-D
M6x12 (x3)
M-C
adjustable part (x3)
M-E
M6 washer (x3)
M-F
adjustable part (x2)
M-G
spacer (x6)
M-H
D6 washer (x6)
W-C
8cm extension pipe (x1)
F
NOTE: Read the entire instruction manual before you start installation and assembly.
WARNING
• Do not begin the installation until you have read and understood the instructions
and warnings contained in this installation sheet. If you have any question
regarding any of the instructions or warnings, please contact your local distributor.
• This mounting bracket was designed to be installed and utilised ONLY as
specified in this manual. Improper installation of this product may cause damage
or serious injury.
• This product should only be installed by someone with good mechanical ability
who has basic building experience and fully understands this manual.
• Make sure that the supporting surface will safely support the combined weight of
the equipment and all attached hardware and components.
• Always use an assistant or mechanical lifting equipment to safely lift and position
the equipment.
• Tighten screws firmly, but do not over tighten. Over tightening can cause damage
to the items, This greatly reduces their holding power.
• This product is intended for indoor use only. Using this product outdoors could
lead to product failure and personal injury.

WARNING
• Installers are responsible to provide hardware for other types of mounting situations.
• Installers must verify that the supporting surface will safely support the combined weight of the
equipment and all attached hardware and components.
4
3
1a. Wood Ceiling Mounting
2
1
Drill three
pilot holes
3
Screw the
ceiling plate
onto the ceiling
Installers must verify that the supporting surface will safely support the combined weight of
the equipment and all attached hardware and components.
WARNING
1b. Solid Brick and Concrete Mounting
1
2
W-A
Drill three pilot
holes
Screw the
ceiling plate
onto the ceiling
W-A
W-B
W-C
W-C
ø 4.5mm
(ø 3/16")
55mm
(2.2")
55mm
2.2"( )
50mm
(2")
55mm
(2.2”)
55mm
2.2”( )
55mm
(2.2")
ø 10mm
(ø 3/8")
Mark the exact
location of
mounting
holes
Find and mark
the exact location
of mounting holes
XX

3. Attaching the Mounting Legs and the Projector Plate
65
2. Installing the Decorative Cover and the Extension Pipe
Press in the two
bolts at the same
time and connect
extension pipe to
ceiling plate.
Run the projector
cables through
the pipe.
Turn bolt outside
for maximum
safety.
M-D
or
or
M-B
M-H
M-B
M-B
M-H
M-H
3a.common mounting
Locate the projector ’s mounting points.
Screw the mounting legs onto the projector.
DO NOT TIGHTEN ALL SCREWS AT THIS TIME.
E or F

3b. for Toshiba projectors
8
M-D
3b-1. For Toshiba projectors
M-C
7
M-D
M-C
M-F
W-C
M-B
M-H
M-H
M-F
W-C
M-G
M-A
Place the projector plate on the mounting legs, as close as to projector center of gravity as possible.
Slightly adjust the arms to fit slots pattern on the projector plate. And then use screws and washers
to fix the projector plate.
Tighten the all mounting screws which secure the mounting legs to the projector at this time.
Attach the adjustable part to
the projector using the screws.
Locate the projector ’s mounting points.
Screw the mounting legs onto the
projector.
DO NOT TIGHTEN ALL SCREWS
AT THIS TIME.
Place the projector plate on the mounting
legs, as close as to projector center of
gravity as possible. Slightly adjust the
arms to fit slots pattern on the projector
plate. And then use screws and washers
to fix the projector plate.
Tighten the all mounting screws
which secure the mounting legs
to the projector at this time.

109
3b-2. for Philips projectors 4. Hang the Projector onto the Ceiling Mount
5. Adjustment
Adjust to the desired location or tilt.
Press in the two bolts at the same time and connect projector plate to pipe.
Important: Make sure the projector is correctly hooked before releasing the projector.
360°
-15° ~ 15°
Turn bolt outside for maximum
safety.
M-D
M-D
M-C
M-FW-C
M-B
M-H
M-H
M-E
Insert adjustable part into
projector.
Locate the projector ’s mounting points.
Screw the mounting legs onto the
projector.
DO NOT TIGHTEN ALL SCREWS
AT THIS TIME.
Place the projector plate on the mounting
legs, as close as to projector center of
gravity as possible. Slightly adjust the
arms to fit slots pattern on the projector
plate. And then use screws and washers
to fix the projector plate.
Tighten the all mounting screws which
secure the mounting legs to the projector
at this time.