Monoprice 9744 User manual

Maintenance
• Check that the bracket is secure and safe to use at regular intervals(at least every three months).
• Please contact your distributor if you have any questions.
11
PID 9744
2.5~20kg2.5~20kg
(5.5~44lbs)(5.5~44lbs)
2.5~20kg
(5.5~44lbs)

21
NOTE: Read the entire instruction manual before you start installation and assembly.
WARNING
• Do not begin the installation until you have read and understood all the instructions
and warnings contained in this installation sheet. If you have any questions
regarding any of the instructions or warnings, please contact your local distributor.
• This mounting bracket was designed to be installed and utilised ONLY as
specified in this manual. Improper installation of this product may cause damage
or serious injury.
• This product should only be installed by someone with good mechanical ability
who has basic building experience and fully understands this manual.
• Make sure that the supporting surface will safely support the combined weight of
the equipment and all attached hardware and components.
• If mounting to wood wall studs, make sure that mounting screws are anchored
into the center of the studs. The use of a stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position
the equipment.
• Tighten screws firmly, but do not over tighten. Over tightening can cause damage
to the items, This greatly reduces their holding power.
• This product is intended for indoor use only. Using this product outdoors could
lead to product failure and personal injury.
Component Checklist
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation.
If any parts are missing or faulty, telephone your local distributor for a replacement.
Package M
Package W
ST6.3x55 (x3)
W-A
concrete anchor (x3)
W-B
articulated arm assembly
A
4mm Allen key (x1)
D
6mm Allen key (x1)
E
D8 washer (x4)
M-F
D5 washer (x4)
M-E
small spacer (x8)
M-G
M5x14 (x4)
M-B
M6x14 (x4)
M-C
M8x20 (x4)
M-D
M4x14 (x4)
M-A
wrench (x1)
F
VESA plate
C
Knob(x2)
B

4
3
2
ø 4.5mm
(ø 3/16")
55mm
(2.2")
55mm
(2.2")
WARNING
• Make sure that mounting screws are anchored into the center of the studs. The use of a stud
finder is highly recommended.
• Installers are responsible to provide hardware for other types of mounting situations.
• Installers must verify that the supporting surface will safely support the combined weight of the
equipment and all attached hardware and components.
Drill pilot holes
3
Screw the wall
mount onto
the wall
X X
√
W-A
Find and mark the
exact location of
mounting holes
1
2a. For Wood Stud Wall Mounting
X
1. Removing the Decorative Covers

65
4. Installing the VESA Plate
Top of the TV
X X
√
Drill pilot holes
1
2
Screw the wall
mount onto
the wall
60mm
(2.4")
60mm
(2.4")
ø 10mm
(ø 3/8")
W-B
W-A
Mark the exact
location of
mounting holes
Mark the exact
location of
mounting holes
Mark the exact
location of
mounting holes
3. Installing the Decorative Covers
2b. For Solid Brick and Concrete Mounting
Installers must verify that the supporting surface will safely support the combined weight of
the equipment and all attached hardware and components.
WARNING

87
Tighten all screws but do not over tighten.
Screw the VESA plate onto the TV.
5. Hooking the TV onto the Wall Mount
· Level the TV.
· Place the lower knobs and tighten all knobs.
Loosen the upper knobs leaving
a 4mm space to the VESA plate.
Hooking the TV onto the wall mount
4mm
or
TV
TV
TV
TV
M-A/M-B
M-C/M-D
M-E
M-F
M-D
M-F
M-G
M-G
M-D
M-F
M-G
F
B

10
6. Tension Adjust
Please keep the arm level during tension adjustment. Use a proper Allen key to slightly loosen or tighten the
adjustment screw according to the TV weight.
If TV settles on its own, rotate adjustment screw towards the "+" symbol.
If TV rises on its own, rotate adjustment screw towards the "-" symbol.
7. Cable Management
Connect the cables to the TV, and press cable cover inward to route
the cables through the space.
Note: Leave slack in the cable for cantilever arm movement. Adjust to the desired position or tilt.
8. Adjustment
9
height adjustable
max335mm
+15°
-15°
180°
180°
180°
+3° -3°
E
Please tighten the socket set screw if the
joints make popping sounds during use.
Tighten the screws using an Allen key (or tighten the knob) untill
the display angle is held.
D