Monster ADVENTURER MAX MT-MS22101 User manual

Model No.: MT-MS22101
Quick Start Guide
Please read this Quick Start Guide carefully
and keep it for future use.

Product Overview
•Speaker Unit
•USB-C Charging Cable
•AUX IN Audio Cable
•Baldric
•Quick Start Guide, General Safety Warnings & Warranty Card
1. Power On/O Button, Mode Button, audio input selection
Charging LED Indicator
2. Bluetooth Pairing, disconnect/connect, Mode LED Indicator
3. Volume Control “-” Button, volume down, track backward
4. Multi Function Button (MFB), music play/pause…
Indoor/outdoor audio switching
5. Volume Control “+” Button, volume up, track forward
1 2 3 4 5

6. USB-C Charging Input
7. Reset Button
8. AUX IN Port
9. MIC IN Port (6.35mm)
10.USB IN (Audio) Port
11. SD Slot
12.Handle
6 7 8 9 10 11
12

Power/Charging
For better enjoyment, you should fully charge the speaker
before use.
The package includes a USB-C charging cable (charge only,
no data transfer function) that can be connected to your
computer or other device made for standard USB compatible
charging. Charging with 5V/2A or above power adapter (not
included).
Caution: ONLY use computer USB output or standard 5 volt
only power adapter for charging.
Damage may occur if non-standard USB power adapter is
used for charging. Do not charge if connector and/or device is
wet or damaged.
Power On/O
In power o mode, press and hold the Power On/O Button
for about 2 seconds to power on the speaker, you hear the
opening tone.
To power o the speaker, press and hold the Power On/O
Button for about 2 seconds again, you will hear a shutdown
tone.
Caution: If no Bluetooth device is connected, the speaker will
be turned o within about 15 minutes.
Pairing
When you unbox the speaker and power it on for the first
time, it will enter to pairing mode automatically.
If Bluetooth device is connected, press and hold the Bluetooth
button for about 3 seconds, disconnect and ready to pair
another device.
If speaker does not connect any Bluetooth device, it will enter
to pairing mode automatically.
During pairing, activate Bluetooth on your phone and set it to
search for new Monster device for pairing. When the speaker
is connected successfully, connected tone will be heard and
the blue LED will stop flashing and the LED indicator will
remain on.
•
•
•

Volume Control
Short press the Volume Button “+” or “-” to turn volume up or
down.
Music
Play/Pause: In the music playback mode, press the MFB to
play/pause music.
Track forward: In the music playback mode, press and hold the
Volume “+” Button for 2 seconds for next song.
Track backward: In the music playback mode, press and hold
the Volume “-” Button for 2 seconds for previous song.
SD Card Playback
When speaker is on and SD card is inserted, SD card is the
priority playback source. If you want to use Bluetooth function,
press the “①” Button to switch the source.
AUX IN Playback
When speaker is on and audio source is inserted via AUX IN,
AUX IN is the priority playback source. If you want to use
Bluetooth function, press the “①” Button to switch the source.
USB IN (Audio) Playback
When speaker is on and USB drive is inserted, USB IN (Audio)
is the priority playback source. If you want to use Bluetooth
function, press the “①” Button to switch the source.
Playback Priority
The Bluetooth mode is the default playback mode, when there
are multiple audio sources, the playback priority is as follows:
• SD Mode – first priority
• AUX IN Mode – second priority
• USB IN（AUDIO) Mode – third priority
• Bluetooth Mode – fourth priority

Audio source can be switched by press the “①” Button, the
sequence is as follows:
Microphone (Dynamic -60dB 3dB)
When speaker is on, microphone is ready to use after plugging
the jack into the MIC IN Port and switch on.
Power Saving Setting
In Bluetooth mode, when no device is connected, the speaker
will be switched o automatically in 15 minutes.
SD card mode/AUX IN mode/ USB IN (AUDIO) mode or
Bluetooth mode, no music playback for 15 minutes, the
speaker will be switched o automatically.
If microphone is plugged in and idled over 15 minutes, the
speaker will be switched o automatically.
Indoor/outdoor audio mode switching
When the speaker is on, press and hold the multi-function
button for 3 seconds to switch the indoor/outdoor sound
mode.
Reset Device
If there is a malfunction, press the Reset Button by using a
paper clip.
SD Mode AUX IN Mode USB IN（AUDIO)Mode Bluetooth Mode
•
•
•
±

LED Indicator Guide
Status
Power On
Power O
Pairing
SD Mode
USB IN Mode
AUX IN Mode
Battery low
Description
LED Indicator: white LED stays On
LED Indicator: White LED lights o
Mode LED Indicator: blue LED flashes quickly
Mode LED Indicator: blue LED stays On
Mode LED Indicator: red LED stays On
Mode LED Indicator: pink LED stays On
Mode LED Indicator: green LED stays On
-
Voice/Tone
Opening Tone
“Goodbye”
“Discovering”
-
-
-
“Battery low”
-
Special Note:
• indicates the handle of the Bluetooth speaker, maximum
weight cannot exceed 25kg to avoid any accidents.
Battery Use Caution:
•It is not recommended to replace the battery privately.
•The battery (battery pack or battery pack combination) must
not be exposed to sunshine, fire or similar overheated
environments.
Bluetooth
Connected
“Your device is
connected”
Charging LED Indicator: red LED lights when
charging, turns o after fully charged
Charging

Specifications
For Techincal and Warranty Support:
1300 886 649
tempo.org/support
Distributed by Tempo (Aust) Pty Ltd,
PO Box 132, Frenchs Forest NSW 1640
Input 5V, 2A
IPX7
11.1V, 4000mAh
2 x 30W
2 x 15W
5.0
10m
Up to 64GB
3.47kg
399mm x 214mm x 160mm
(W x H x D)
Ingress Protection
Battery
Speaker (Main base) Output
Speaker (Treble) Output
Bluetooth
Bluetooth Operation Range
USB/Micro SD Format
Dimensions
Net Weight

Compliance and Responsible Disposal
Packaging
The packaging of your product has been selected from
environmentally friendly materials and can usually be
recycled. Please ensure these are disposed of correctly. Plastic
wrapping can be a suocation hazard for babies and young
children, please ensure all packaging materials are out of
reach and are safely disposed of. Please recycle these
materials rather than throwing them away.
Product
At the end of its working life, do not throw this product out
with your household rubbish. An environmentally friendly
method of disposal will ensure that valuable raw materials
can be recycled. Electrical and electronic items contain
materials and substances which, if handled or disposed of
incorrectly, could potentially be hazardous to the environment
and human health.
Compliance
This product complies with the Australian Safety
Standard AS/NZS 62368.1 to ensure the safety
of the product.

Notes