Mont Alpi MAPZ-SS User manual

1
MAPZ-SS Pizza Oven
Assembly Instructions

2
Parts List
No. Description Qty
1. Pizza Stone_____________________________________1
2. Pizza Stone Grid_________________________________1
3. Front Door_____________________________________1
4. Chimney_______________________________________1
5. Chimney cap ___________________________________1
6. Oven Body _____________________________________1
7. Grease Tray ____________________________________1
8. Leg ___________________________________________4
9. Gas Bottle Holder ________________________________1
10. Match Lighting Rod_______________________________1

3
Assembly Instructions
Before assembly, make sure all parts are present. If any part is missing or damaged, do not attempt to
assemble the appliance.
Tools Required
Philips screwdriver (not included)
1. Leg Assembly

4
2. 1lb Gas Cylinder Hook Assembly

5
3. Chimney Assembly
4. Cooking Grid Assembly

6
5. Pizza Stone Assembly

7
6. Grease Pan Assembly
7. Clean the Fire Box Base
WARNING
The bottom needs to be assembled and fixed by screw after each cleaning.
Tools required: Philips screwdriver

8
8. Connecting the 1lb Gas Cylinder
WARNING
Always keeps the gas bottle in an upright position.
The maximum 1lb LP gas tank is 4” in diameter and 8” tall.
The cylinder must be disconnected when the oven is not in use
Only cylinders marked as “propane” must be used.

9
9. Connecting to a 20lb Gas Cylinder
WARNING
WARNING
Always keeps the gas bottle in an upright position.
The maximum 20lb LP gas tank is 12.2”in diameter and 17.9” tall.
The cylinder must be disconnected when the oven is not in use.
The cylinder used must include a collar to protect the cylinder valve.
The minimum distance for the oven and the 20lb gas tank is 40”.
Additional gas hose to connect the 1lb
gas cylinder regulator and 20lb gas
cylinder valve.

10
10. Opening the Front Door

11
Connecting the Liquid Propane Gas Cylinder
To connect the liquid propane gas cylinder:
1. The cylinder valve should be in the OFF position.
2. Make sure the burner valve is in the OFF position.
3. Inspect the valve connections, port and regulator assembly. Remove debris and inspect the
hose for damage.
4. When connecting the regulator assembly to the valve, use your hand to tighten the nut
clockwise until it stops. *the use of a wrench could damage the quick coupling nut and result in
a hazardous situation*
5. Open the cylinder valve fully by turning the valve counterclockwise.
6. Before lighting the grill, use a soap and water solution to check all connections for leaks.
7. If a leak is found, turn the cylinder valve OFF and do not use the grill until a local liquid propane
dealer can make repairs.
Disconnecting the Liquid Propane Gas Cylinder
To disconnect the liquid propane gas cylinder:
1. Turn the grill burner vale OFF and make sure the grill is cool.
2. Turn the liquid propane cylinder valve OFF by turning clockwise until it stops.
3. Detach the regulator assembly from the cylinder valve by turning the quick coupling nut
counterclockwise.
4. Place the dust cap for the cylinder valve outlet whenever the cylinder is not in use.
Leak Testing
General
Although the gas connections of the appliance are leak tested prior to packing and shipment, a
complete test must be performed at the installation site. Before each use, check all the gas connections
for leak testing using the procedure listed below. If the smell of gas is detected at any time, you should
immediately stop using and check the entire system for leaks.
Before Testing
Make sure all packaging has been removed from the appliance.
Make a solution of one part liquid detergent and one part water. You will need a spray bottle, brush or
rag to apply the solution to the fittings.
To Test
1. Turn the burner valve OFF
2. Turn the liquid propane cylinder valve off counterclockwise to open the valve.
3. Apply the soap solution to all gas fittings. Soap bubbles will appear where a leak is present.
4. If a leak is present, immediately turn the gas supply OFF and tighten leaky fittings.
5. Turn the gas back ON and recheck
6. Should the gas continue to leak from the any of the fittings, turn the gas supply OFF and
contact customer service.
Lighting Instructions
To Light the Burner
1. Read the instructions before lighting.
2. Make sure the control knob is in OFF position, and then turn the liquid propane cylinder valve ON by
slowly turning counterclockwise.
3. Open the front door, push and turn the burner knob to HIGH, burner should light immediately.
4. If burner doesn’t light up, turn the knob OFF, wait 5 minutes and repeat the lighting.
To Match Light the Oven
If the burner will not light after several attempts using the control knobs, the burner may be lit with a
match.
1. If you have already attempted to light the burner using the control knob, wait 5 minutes for any gas to
dissipate.
2. Insert a match into the light rod, ignite the match and insert through the pizza stone grid to the
burner.
3. Push and turn the control knob to HIGH slowly, the burner should ignite immediately.
4. If the burner does not light within seconds, turn the control knob OFF and wait 5 minutes then try
again.

12
Phone: [phone]
Email: John@Mont AlpiOnline.com
Mont Alpi
25541 Arctic Ocean Dr
Lake Forest, CA 92630
Customer service
More from Mont Alpi
COVMAi805 –805 Island durable
weather resistant cover.
MAi805 –Island. All 304 S/S with faux
granite surfaces (white).
MABi400 –Built-in Grill. Natural gas
and propane ready.