Monte Carlo Fan Company 25003 Instruction Manual

60 INCH CEILING FAN WITH LIGHT
Model# 25003
INSTALLATION & USER MANUAL

Table of Contents
Safety Information
2
Table of Contents..................................................
Safety Information.................................................
Dimension Reference ...........................................
Fan Parts Included ................................................
Exploded View ......................................................
Installation Instructions .........................................
Care and Cleaning ................................................
Troubleshooting Guide .........................................
Operation ..............................................................
2
2
12
11
10
5
4
3
3
To reduce the risk of electric shock, ensure electricity
has been turned off at the circuit breaker or fuse box
before you begin.
All wiring must be in accordance with the National
Electrical Code “ANSI/NFPA 70” and local electrical
codes.
Electrical installation should be performed by a
qualified licensed electrician.
The outlet box and support structure must be
securely mounted and capable of reliably supporting
a minimum of 35 lbs (15.9 kg). Use only UL Listed
outlet boxes marked “Acceptable for Fan Support of
35 lbs. (15.9 kg) or less.”
Do not place objects in the path of the blades.
Do not use water or detergents when cleaning the
fan or fan blades. A dry dust cloth or lightly ampened
cloth will be suitable for most cleaning.
After making electrical connections, spliced
conductors should be turned upward and pushed
carefully up into the outlet box. The wires should be
spread apart with the grounded conductor and the
equipment-grounding conductor on one side of the
outlet box and ungrounded conductor on the other
side of the outlet box.
All setscrews must be checked and retightened
where necessary before installation.
READ AND SAVE THESE INSTRUCTIONS.
1.
2.
3.
4.
5.
6.
7.
WARNING: To reduce the risk of electrical shock or
fire,not use this fan with any solid-state fan speed
ontrol device. It will permanently damage the electronic
circuitry.
WARNING: To reduce the risk of personal injury, do
not bend the blade brackets when installing the rackets
balancing the blades, or cleaning the fan. Do not insert
foreign objects in between rotating fan blades.
WARNING: To reduce the risk of fire, electric shock
or personal injury, mount to outlet box marked
“acceptable for fan support of 35 lbs. (15.9Kg) or less”
and use screws provided with the outlet box.
WARNING: To avoid possible electrical shock, turn
the electricity off at the main fuse box before wiring.
WARNING: To reduce the risk of electrical shock,
this must be installed with an lsolating wall
control/switch.
CAUTION: The fan must be mounted with a
minimum of 7 ft (2.1 m) clearance from the trailing edge
of the blades to the floor.
CAUTION: Changes or modifications not expressly
approved by the party responsible for compliance
could void the user’s authority to operate the quipment.
CAUTION: To avoid personal injury or damage to
the fan and other items, use caution when working
around or cleaning the fan.
CAUTION: To reduce the risk of personal injury, use
only the screws provided with the outlet box.
Hardware Included ............................................... 3

Dimension Reference
Hardware Included
Fan Parts Included
2
3
4
5
6
1
3
7
8
9
10
IH 4H 8H
61
2
34
5
5-1/4 in
2-1/2 in
11-1/4 in
16-1/2 in
60 in
11
1. Mounting Bracket
2. Downrod (6”and 10”)
Hanger Ball
Safety Pin & Cotter Pin
3. Canopy
4. Coupler Cover
5. Blade Arm
6. Blade Arm Cover
7. Fan Motor Assambly
8. Lighting Fixture
9. Glass
10.Remote Control(Batteries not included)
11.Fan Blade
Quantity
1
2
1
1
1
1
5
5
1
1
1
1
5
S11
S2
S3
S4
S1 S6
S7
S8
S5
S10
S9
Hardware Package
S1. Blade Screws
S2. Machine Screws
S3. Machine Screws
S4. Wood Screws
S5. Wire Nuts
S6. Blade Arm Screws
S7. Lock Washers
S8. Star Washers
S9. Washers
S10.Paper Washers
S11.Balance Kit
Quantity
16
2
2
2
3
11
2
2
2
16
1

Exploded View
4
Canopy Screws
Mounting Bracket
Canopy
Coupler Cover
Safety Pin
Cotter Pin
Fan Motor
Assembly
Blade
Lighting Fixture
Glass
Protective Cover
Blade Arm Cover
Blade Arm
Blade Arm Screws
Blub (Not Included)
Downrod
Hanger Ball
Joint Screws
Blade screws &
Paper Washers

Installation Instructions
Step1 Attaching the Fan Blade Arm
Attach blade arms to motor using supplied screws. (see
figure 1)
Step2 Assembling the Fan Blade and
Blade Arm Cover
Choose the blade finish that you prefer and attach as
follow:
The decorative side of the blade is facing down so that
the three holes of the blade arm cover, the three holes of
the blade and the three holes of the blade arm are
aligned.
Make the blade arm cover, blade and blade arm
coincide. Hold them together with three blade screws
and paper washers.(see figure 2)
FIG 1
FIG 2
Fan Motor
Assembly
5
Blade Arm Screws
Blade Arm
Fan Motor Assembly
Blade
Blade Arm Cover
Blade Arm
Blade screws &
Paper Washers

Downrod
Canopy
Coupler Cover
Fan Motor
Assembly
Safety Pin Cotter Pin
Installation Instructions
6
Step3 Assembling the Fan
Route the wires exiting the top of the fan motor assembly
into the coupler cover.(see figure 3)
Loosen the set screws in the downrod coupler until the
inside of the channel is clear of the screw tip.
Remove and save the lock pin on the end of the downrod.
Slide the ceiling canopy onto the downrod followed by the
coupler cover.
Attach the downrod into the coupler until the lock pin can
be inserted through the hole in both the rod and coupler.
Tighten both set joint screws on the coupler.
Insert the lock pin through the hole in the coupler and
downrod then attach the hitch pin on the other side.
FIG 3
Step4 Attaching the Mounting Bracket
Pass the 120-Volt supply wires through the center hole
in the mounting bracket.
Install the ceiling mounting bracket on the outlet box
using the two mounting screws provided with the outlet
box. If necessary use leveling washers (not included)
between the mounting bracket and outlet box.
Note that the flat side of the mouting bracket is toward
the outlet box. When using flushmount, it is important
that the mounting bracket be level.
Securely tighten the two outlet box screws.(see figure 4)
FIG 4
Mounting Screws
CAUTION: To ensure wobble-free operation and to
avoid damage to the fan, the downrod and the set crew
must be completely tightened.
Mounting Bracket
WARNING: To reduce the risk of fire, electric
shock or personal injury, mount to outlet box marked
“acceptable for fan support of 35 lbs. (15.9Kg)
or less” and use screws provided with the outlet box.
Joint Screws

Installation Instructions
7
Step5 Hanging the fan
Carefully lift the fan motor assembly up to the mounting
bracket.
Seat the hanger ball portion of the downrod assembly in
the mounting bracket socket. Ensure that the tab on the
mounting bracket socket is properly seated in the groove
in the hanger ball. (see figure 5)
Step6 Installing Receiver Assembly
FIG 5
Mounting Bracket
Downrod
Fan Motor
Assembly
FIG 6
Receiver
Canopy
Fan Motor
Assembly
Hanger Ball
Connect receiver to mounting bracket as shown. Ensure
all the electrical connections (see Step 7)are tight and
secure to the fan motor assembly. Make sure the fan is
earthed correctly as shown. (see figure 6)
After completing the above steps, raise the canopy to
cover the receiver and bracket. Once secure and no
cables or antenna are visible, then screw down the sides
of the canopy. (see Step 8)

Installation Instructions
8
Step7 Electrical Connection
Remember to disconnect the power.
Follow the steps below to connect the fan to your household wiring. (see figure 7)
Use the wire connecting nuts supplied with your fan.
Secure the connectors with electrical tape.
Make sure there are no loose strands or connections.
Between fan and receiver:
Connect the white wire marked "LIGHT N" from the fan to the white wire marked "FOR LIGHT N" from the
receiver.
Connect the blue wire marked "LIGHT L" from the fan to the blue wire marked "FOR LIGHT L" from the
receiver.
Connect the pink wire from the fan to the pink wire marked "TO MOTOR" from the receiver.
Connect the gray wire from the fan to the gray wire marked "TO MOTOR" from the receiver.
Connect the red wire from the fan to the red wire marked "TO MOTOR" from the receiver.
Between receiver and mains:
Connect the black live wire marked "AC IN L" from the receiver to the live wire (typically black) from the outlet
box.
Connect the white neutral wire marked "AC IN N" from the receiver to the neutral wire (typically white) from the
outlet box.
Connect the green ground wire from the receiver to the ground wire (bare orgreen) from the outlet box.
FIG 7
Mounting
Bracket
Hanger Ball
Antenna:
DO NOT CUT OR SPLICE.
BLACK AC IN L
WHITE AC IN N
GREEN
Outlet box
(Mains cables)
GREEN
N
L
WHITE LIGHT N
BLUE LIGHT L
PINK TO MOTOR
GRAY TO MOTOR
RED TO MOTOR
WHITE LIGHT N
BLUE LIGHT L
PINK MOTOR
GRAY MOTOR
RED MOTOR
FAN

Installation Instructions
9
Step8 Mounting the fan Canopy FIG 8
Mounting Bracket
Fan Motor
Assembly
Canopy
Canopy
Screws
Step9 Installation of Lighting Fixture
Loosen the screws of the protective cover and remove
the protective cover.
A wire connector (female) is located inside the fan motor
assembly and a male connector extends from the
lighting fixture. Push them together.
A wire connector (male) is located inside the fan motor
assembly and a female connector extends from the
lighting fixture. Push them together.
Align the three bumps on the fan motor assembly with
the three grooves on the lighting fixture and rotate the
lighting fixture clockwise until locked. (see figure 9)
FIG 9
Fan Motor
Assembly
Lighting Fixture
Protective Cover
Remove the two non-slotted mounting screws on the top
of the canopy.
Back the two slotted screws out about half way.
This will enable you to remove the mounting cover plate
from canopy.
Align the locking slots of the ceiling canopy with the two
canopy screws in the mounting cover plate.
Push up to rengage the slots and turn clockwise to lock
in place.
Firmly tighten the two canopy screws.
Install the two canopy screws into the holes in the
canopy and tighten firmly.(see figure 8)
Downrod

Installation Instructions
Care and Cleaning
10
Step10 Installing the Bulb and Glass
Install three LED bulbs(not included) and screw them in
clockwise until fastened.(see figure 10)
Put the glass in the protective cover, align the light fixture
screw hole, tighten the screw.
CAUTION:When installing the glass, align the three
screws with the sponge mat in the three glass slots and
tighten the screws.Otherwise, you may damage the
glass.
FIG 10
WARNING: Make sure the power is off before
cleaning your fan.
Blub
Protective
Cover
Lighting
Fixture
Glass
Because of the fan’s natural movement, some connections may become loose. Check the support connections,
brackets, and blade attachments twice a year. Make sure they are secure. It is not necessary to remove the fan
from the ceiling.
Clean your fan periodically to help maintain its new appearance over the years. Do not use water when cleaning,
as this could damage the motor or the wood, or possibly cause an electrical shock. Use only a soft brush or
lint-free cloth to avoid scratching the finish. The plating is sealed with a lacquer to minimize discoloration or
tarnishing.
You can apply a light coat of furniture polish to the wood for additional protection and enhanced beauty. Cover
small scratches with a light application of shoe polish.
You do not need to oil your fan. The motor has permanently-lubricated sealed ball bearings.
Always unplug the fan before cleaning, disassembly or servicing.
Glass
Sponge Mat
Protective
Cover
Lighting Fixture
Screws
Rubber
Washers
CAUTION-RISK OF FIRE
USE MAX. 5W TYPE E12 C35 LED BULB 120V 60Hz
Please use dimmable bulbs when you want to use the dimmable
function.