5
STEP 1
With two people, carefully lift the cabinet
onto a soft mat, or the cardboard the tool
cabinet came in, and place under the
bottom for protection. Remove the M4x16
Phillips head screws and bumpers from
the two sides using a Phillips screwdriver
and lay the two sides down carefully.
NOTE: Do not discard the bolts and
bumpers. They will be installed in the next
section.
STEP 2
Using the M4 x 16 Phillips head screws
and bumpers, the ones just removed,
reattached to secure the bottom of the
side cabinets in place so the bumper
is next to the drawer cabinet. This will
prevent the doors from swinging inward
when the cabinet is closed.
STEP 3
Release the cable ties from the back of the
cabinet and unfold the side panels which
are hinged and folded behind the drawer
cabinet and align them with the bottom of
the side cabinets. NOTE: Do not unfold the
wood top until later. It will make installing
the bolts in the next section much easier.
STEP 4
Position the top front and back edge of the
side cabinet body evenly with the drawer
section over the holes and attach with the
M6x16 bolts provided. Tighten securely
using a Phillips screwdriver.
STEP 5
Position the bottom and side walls of the
side cabinets over the holes and attach
with the M6x16 bolts provided (2pcs for
each side and one for the top), tighten
securely using a Phillips screwdriver.
STEP 6
Attach the side handle by positioning it
over the holes on the side cabinet and
attach with 4 pcs of the M6x12 bolts
provided. Tighten securely using a 10mm
socket.
tOOLS REQUiRED FOR aSSEMBLY
FiRSt
Carefully lift the cabinet on to a soft mat
using the two thicker packaging materials
under the bottom for protection. Remove
the M4x12 Phillips pan head screws and
bumpers from the two sides using a
Phillips screwdriver and lay them down
carefully. NOTE: Do not discard the bolts
and bumpers. They will be installed in the
next section.
Packaging Material
Bamboo Work Top
SECOND
Reattach the M4x12 Phillips pan head
screws and bumpers to the drawer
section. They will prevent the doors
from going inward when closing.
tHiRD
Release the cable ties from the back of the
cabinet and unfold the side panel making
sure to align them with the bottom shelf.
NOTE: Do not unfold the bamboo top until
later. It will make installing the bolts in the
next section much easier.
FOURtH
Position the top front and back edge
evenly with the drawer section over the
holes and attach with the M6x20 bolts,
lock washers and washers provided.
Tighten securely using a 10mm socket.
FiFtH
Position the bottom and side walls of the
side box over the holes and attach with
the M6x16 bolts, lock washers and
washers provided. Tighten securely
using a Phillips screwdriver.
aSSEMBLY iNStRUCtiONS aSSEMBLY iNStRUCtiONS
SiXtH
Simply position the side handle over the
holes and attach with the M6x20 bolts
provided. Tighten securely using a
10mm socket.
SEVENtH
It is now time to install the bamboo top.
It may be easier to partially insert the front
M6x16 bolts, lock washers and washers to
help align the holes. Do not tighten until all
the holes are aligned. Once all the holes
are aligned, tighten the bolts securely
being careful not to strip the bamboo top.
EiGHtH
Carefully lay the cabinet on its back using
the packaging or a soft mat as protection.
step. Position the swivel casters on the
bottom right side. This should be the
same side as the side handle. Insert the
4 M8x20 bolts and washers and tighten
securely using a 14mm wrench of socket.
casters. Carefully lift the cabinet back on
its casters.
NiNtH
Insert the bracket supports for the shelves
at the desired height making sure that all
four are level. Install the shelf by inserting
it at an angle slightly above the brackets.
tENtH
Install the doors by aligning the bottom
peg in the hole then simply depress the
spring pin for the top pin and align it in
the top hole.
Page 4 Page 5
tOOLS REQUiRED FOR aSSEMBLY
FiRSt
Carefully lift the cabinet on to a soft mat
using the two thicker packaging materials
under the bottom for protection. Remove
the M4x12 Phillips pan head screws and
bumpers from the two sides using a
Phillips screwdriver and lay them down
carefully. NOTE: Do not discard the bolts
and bumpers. They will be installed in the
next section.
Packaging Material
Bamboo Work Top
SECOND
Reattach the M4x12 Phillips pan head
screws and bumpers to the drawer
section. They will prevent the doors
from going inward when closing.
tHiRD
Release the cable ties from the back of the
cabinet and unfold the side panel making
sure to align them with the bottom shelf.
NOTE: Do not unfold the bamboo top until
later. It will make installing the bolts in the
next section much easier.
FOURtH
Position the top front and back edge
evenly with the drawer section over the
holes and attach with the M6x20 bolts,
lock washers and washers provided.
Tighten securely using a 10mm socket.
FiFtH
Position the bottom and side walls of the
side box over the holes and attach with
the M6x16 bolts, lock washers and
washers provided. Tighten securely
using a Phillips screwdriver.
aSSEMBLY iNStRUCtiONS aSSEMBLY iNStRUCtiONS
SiXtH
Simply position the side handle over the
holes and attach with the M6x20 bolts
provided. Tighten securely using a
10mm socket.
SEVENtH
It is now time to install the bamboo top.
It may be easier to partially insert the front
M6x16 bolts, lock washers and washers to
help align the holes. Do not tighten until all
the holes are aligned. Once all the holes
are aligned, tighten the bolts securely
being careful not to strip the bamboo top.
EiGHtH
Carefully lay the cabinet on its back using
the packaging or a soft mat as protection.
step. Position the swivel casters on the
bottom right side. This should be the
same side as the side handle. Insert the
4 M8x20 bolts and washers and tighten
securely using a 14mm wrench of socket.
casters. Carefully lift the cabinet back on
its casters.
NiNtH
Insert the bracket supports for the shelves
at the desired height making sure that all
four are level. Install the shelf by inserting
it at an angle slightly above the brackets.
tENtH
Install the doors by aligning the bottom
peg in the hole then simply depress the
spring pin for the top pin and align it in
the top hole.
Page 4 Page 5
