Montigo H34VO E Series Instruction Manual

WARNING
FOR OUTDOOR USE ONLY.
WARNING
CARBON MONOXIDE HAZARD
This appliance can produce carbon monoxide which has
no odor. Using it in an enclosed space can kill you.
Never use this appliance in an enclosed space such as a
camper, tent, car or home.
WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could result in serious injury,
death, or property damage.
—Donotstoreorusegasolineorotherammablevaporsand
liquidsinthevicinityofthisoranyotherappliance.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any
phoneinyourbuilding.
• Leavethebuildingimmediately.
• Immediatelycallyourgassupplierfromaneighbour's
phone. Follow the gas supplier’s instructions.
• Ifyoucannotreachyourgassupplier,callthere
department.
—Installationandservicemustbeperformedbyaqualied
installer,serviceagencyorthegastter.
DivineOutdoor
OUTDOOR RESIDENTIAL GAS FIREPLACE
H34VO*,H34VO*E
Natural Gas or Propane Gas
H38VO*,H38VO*E
Natural Gas or Propane Gas
Installation and service must be performed by a qualied installer,
service agency or the gas tter. Check local codes and read all
instructions prior to installation.
Installer: Leave this manual with the appliance. Please refer to the
Montigo website for the most current version of the replaces manual
Consumer: Retain this manual for future reference. Please refer to the
Montigo website for the most current version of the replaces manual
NOTICE
Some materials used in the manufacturing process of this product can
expose you to Benzene which is known in the State of California to
cause cancer and birth defects or other reproductive harm. For more
information go to www.P65warnings.ca.gov
WARNING
HL38VO*,HL38VO*E
Natural Gas or Propane Gas
H42VO*,H42VO*E
Natural Gas or Propane Gas
XG0150
Installation & Maintenance Manual
®
C
US
SCAN THE QR CODE OR VISIT THE
WEBSITE TO VIEW THE MOST RECENT
VERSION OF THE MANUAL
WWW.MONTIGO.COM/PRODUCT-GUIDES
IMPORTANTIMPORTANT

Page 2
You must read and understand this manual prior to installation, operation or
troubleshooting this appliance. Please retain this owner’s manual for future reference
and maintenance.
NOTICE
XG0150 - 140707.2
Table of ContentsTable of Contents
Divine Outdoor Gas Fireplace
Introduction .............................................................................3
Models .............................................................................3
Installation
Before you Start .............................................................................4
Installation Checklist...........................................................................4
Section 1: Installation Overview and Product Dimensions ...................5
Section 2: Framing the Fireplace ........................................................6
Clearances ....................................................................... 6 - 7
Finishing around the Fireplace ........................................................7
Section 3: Venting ......................................................................... N/A
Section 4: Wiring .............................................................................8
▪ Honeywell gas control and pilot ..........................................8
Section 5: Installing the Gas Line........................................................9
Section 5-1: Fuel Conversion ..............................................................9
Section 5-2: Gas Pressure ..................................................................9
Section 5-3: Gas Connection...............................................................9
Section 6: ......................................................................... N/A
Section 7: Installing and Removing the Door.....................................10
Section 8: Installing the Accessories......................................... 11 - 14
▪ Installing the H34VON Log Set...............................................11
▪ Installing the H38VON Log Set...............................................12
▪ Installing the H42VON Log Set...............................................13
▪ Installing the HL38VOL Firestones .........................................14
Section 9: Operation .................................................... 15 - 16
▪ Start-up Sequence with Continuous Pilot...............................15
▪ Start-up Sequence with Honeywell Electronic Ignition ..........16
Maintenance .................................................................. 17 - 18
▪ General ...........................................................................17
▪ Cleaning ...........................................................................17
▪ Hi-Lo Burner Adjustment .......................................................17
▪ Pilot Burner Adjustment.........................................................17
▪ Replacement Parts................................................................18
Appendix
A. Termination Locations ..........................................................19
B. Warranty ...........................................................................20
C. State of Massachusetts. .......................................................21
Installer: Leave this manual with the appliance. Do not remove.
Consumer: Retain this manual for maintenance and future reference. Do not Discard.
NOTICE

Page 3
XG0150 - 140707.2
Indicates a hazardous situation which, if not
avoided, WILL result in death or serious
injury or property damage.
Indicates a hazardous situation which, if not
avoided, COULD result in death or serious
injury or property damage.
Indicates a hazardous situation which, if not
avoided, WILL result in minor or moderate
injury.
Address practices that are important, but
not related to personal injury
DANGER WARNING
CAUTION NOTICE
Divine Outdoor Gas Fireplace
Safety Alert KeySafety Alert Key
IntroductionIntroduction
WARNING
Hot glass will cause
burns. Do not touch
glass until unit is cooled.
Never allow children to
touch glass.
Irritant
Cutting
Watch your step
Slippery floor
High temperatures
Glass hazard
Danger of suffocation
High voltage
Toxic
Flammable materials
Corrosive
Fork lift trucks
Danger overhead crane
Explosion risk
Oxidising
Danger of death
Biohazard
Laser Radiation
Danger of entrapment
Hot surface
General Warning
Blank
Gas bottles
Watch for
falling objects
Electricity
Danger for cutter
Entrapment hazard
Battery hazard
Rotating parts
Low temperature
Strong magnetic field
Optical radiation
Non ionizing
radiation
Radiation
Hazardous to the
Environment
Danger of harming
your hands
Congratulations on your purchase of a Montigo Fireplace.
With over 30 years of experience, Montigo is committed to providing
you with a gas fireplace that is not only a beautiful addition to your
space, but that is also designed and manufactured to the highest
safety, reliability and engineering standards.
We strongly encourage you to read and carefully follow the instructions
laid out in this Installation, Operation and Maintenance Manual and
retain it for your future reference. Pay special attention to all cautions,
warnings, and notices throughout this manual intended to ensure
your safety.
This manual covers installation, operation and maintenance. Lighting,
operation and care of this fireplace can be easily performed by the
homeowner. All installation and service work should be performed
by a qualified or licensed installer, plumber or gas fitter as certified
by the state, province, region or governing body where the fireplace
is being installed.
This installation, operation and maintenance manual is applicable
to the models described below. Refer to your rating plate to verify
included options.
How to use this manual:
This manual covers installation, operation and maintenance. Lighting,
operation and care of this fireplace can be easily performed by the
homeowner. However, all installation and service work should be
performed by a qualified or licensed installer, plumber, or gasfitter
who is qualified or licensed by the state, province, region,or governing
body in which the appliance is being installed.
Warranty and Installation Information: (See Appendix B)
The Montigo warranty will be voided by, and Montigo disclaims any
responsibility for, the following actions:
▪ Modification of the fireplace and/or components including
Direct-Vent assembly or glass doors.
▪ Use of any component part not manufactured or approved by
Montigo in combination with this Montigo fireplace system.
▪ Installation other than as instructed in this manual.
Consult your local Gas Inspection Branch on installation requirements
for factory-built gas fireplaces. Installation & repairs should be done
by a qualified contractor.
MODEL Natural Gas Liquid Propane Gas Rating (BTU hr) Traditional Burner Linear Burner Standing Pilot Ignition Honeywell Hot Surface Ignition
H34VON X 26,000 X X
H34VOL X 26,000 X X
H38VON X 34,000 X X
H38VOL X 34,000 X X
HL38VON X 34,000 X X
HL38VOL X 34,000 X X
H42VON X 40,000 X X
H42VOL X 40,000 X X
H34VONE X 26,000 X X
H34VOLE X 26,000 X X
H38VONE X 34,000 X X
H38VOLE X 34,000 X X
HL38VONE X 34,000 X X
HL38VOLE X 34,000 X X
H42VONE X 40,000 X X
H42VOLE X 40,000 X X

Divine Outdoor Gas Fireplace
Page 4 XG0150 - 140707.2
InstallationInstallation
Installation and repairs should be done by an authorized gas fireplace service technician.
The appliance should be inspected before use and at least annually by a professional. More
frequent cleaning may be required due to excessive lint from carpeting, bedding material,
etc. It is imperative that control compartments, burners and circulating air passageways of
the fireplace are kept clean.
NOTICE
Due to high operating temperatures, this appliance should be located out of traffic &
away from furniture and draperies.
Children and adults should be alerted to the hazards of the high surface temperature,
which could cause burns or clothing ignition.
Young children should be carefully supervised when they are in the same room as the
appliance.
Clothing or other flammable materials should not be placed on or near the appliance.
CAUTION
When this appliance is installed directly on any combustible material other than wood
flooring, it must be installed on a metal or wood panel extending the full width and
depth of the appliance or a fire will occur causing serious injury, property damage or
even death.
DANGER
Installation Checklist
Determine the desired install location of your fireplace.
See Section 1, Dimensions on Page 5, and refer to the Framing
Section 2 for details.
Layout Electrical Requirements Refer to Section 4: Wiring,
for Details.
Refer to Section 5: Installing the Gas Line, for details on the
gas connection and access.
Refer to local codes and guidelines for installation requirements.
Installation and repairs should be done by a qualified
contractor and must conform to:
• Installations in Canada must conform to the current CAN/CGA
B-149.1 and .2 Gas Installation Code and local regulations.
• Installations in Canada must conform to the local codes or in
the absence of local codes to the current version of Natural Gas
and Propane Installation Code, CSA B149. Electrical Installations
must conform to the local codes or, in the absence of local codes,
to the current version of Canadian Electrical Code, CSA C22.1.1
• Installations in the USA must conform to the local codes or
in the absence of local codes to the current version of National
Fuel Gas Code, ANSI Z223.1/NFPA 54. Electrical Installations must
conform to the local codes or, in the absence of local codes, to the
current version of the National Electrical Code, ANSI/NFPA 70. See
Appendix C for installation within the State of Massachusetts.
IMPORTANT MESSAGE: SAVE THESE INSTRUCTIONS
The Divine Outdoor Ventless fireplace must be installed in accordance
with these Instructions.Carefully read all the Instructions in this manual
first. Consult the Local Gas Branch to determine the need for a permit
prior to starting the installation. It is the responsibility of the installer to
ensure this fireplace is installed in compliance with the manufacturers
instructions and all applicable codes.
BEFORE YOU START:
Young children should be carefully supervised when they are
in the same room as the applicance. Toddlers, young children
and others may be susceptible to accidental contact burns. A
physical barrier is recommended if there are at risk individuals
in the house. To restrict access to a fireplace or stove, install
an adjustable safety gate to keep toddlers, young children and
other at risk individuals out of the room and away from hot
surfaces.
CAUTION

Divine Outdoor Gas Fireplace
Page 5
XG0150 - 140707.2
InstallationInstallation
Section 1: Installation Overview and Product Dimensions
Please review the Installation Checklist for general information on
preparing for a successful installation of your fireplace.
The Divine VO fireplace may be installed in any location that maintains
proper clearances to air conditioning ducts, electrical wiring and
plumbing. Safety,as well as efficiency of operation,should be considered
when selecting the fireplace location. Try to select a location that does
not interfere with room traffic, and has adequate ventilation.
Figure 1. Fireplace dimensions
A B C D E F G H I J K L M N O P Q
H34VO 33⁄ 35⁄ 24 33⁄ 27¼18¼34¼33¾31⁄ 21⁄ 23 5½ 5¼ 19¼18⁄ 33¼17
H38VO 37¾39¼27 37¾32⁄ 21⁄ 37¼36½34¾24½25¾ 5½ 5¼ 2⁄ 19¾37 18⁄
H42VO 42 43½29½42 36½25½41¼4½39 28½28⁄ 6⁄ 5¼ 21⁄ 2¾41 19⁄
A
N
O
B
H
E
G
C
I
JF
D
K
L
M
P
Q
DIMENSIONAL
DRAWING IS
SHOWN WITHOUT
SCREEN. REFER TO
THE MANUAL FOR
SCREEN DIMENSIONS
SCREEN PROTRUDES
2⅜" FROM FIREPLACE
FACE
0" CLEARANCE
TO INSULATION
JACKET
0" CLEARANCE TO INSULATION JACKET

Divine Outdoor Gas Fireplace
Page 6 XG0150 - 140707.2
InstallationInstallation
Section 2: Framing
For protection against freezing temperatures, it is recommended that
outer walls of the chase be insulated with a vapour barrier. This will
reduce the possibility of a cold-air convection current on the fireplace.
Choosing The Fireplace Location
The Divine Outdoor VO may be installed in an outdoor setting such as
a patio or balcony. Choose a location that maintains proper clearance
to combustibles as noted in the clearances chart.
Note: Divine Outdoor VO may not be recessed into the exterior wall.
Note: Minimum 2 side of the covered patio/deck must be open
Figure 2. Choosing the fireplace location.
G
H
Top View
F
F
E
J
B
B
D
I
C
D
D
A
A
Front View
G
Side View
P”
N”
Q”
N”
M”
O”
1" clearance
to corners only
Exterior Wall
**Optiona l Drain Pan:
available for all models.
H34VO Part No. OD34123
H38VO Part No. OD38123
H42VO Part No. OD42123
Insulation material
vapor barrier
(exterior wall).
1” Clearance to
combustibles to sides
ot Unit
Figure 2.a Minimum framing dimensions.
A
B
C
D
Be sure to plan a drain system for both in the wall and standalone installations.
*Measurement above grade for US installations
†Dimension is to back wall or back studs
Back wall
with insulation
material vapor
barrier (exterior
wall)
A B C D E F G H
H34VO 38¾ 35⁄ 2¼†12* 61⁄ 35⁄ 43⁄
H38VO 42½ 39¼ 21 ⁄†12* 65⁄ 39¼ 49⁄
H42VO 46½ 43½ 22⁄†12* 72¼ 43½ 51⁄
*Clearance to grade
12" clearance to grade applies in situations where the fireplace and framing
penetrates the building envelope. Additionally, if snow accumulation may
occur, than the 12" clearance should be adhered to.
This 12" clearance can be disregarded in situations where:
• A standalone enclosure has been built or purchased.
• The fireplace and framing does not penetrate the building envelope.
• Covered porches with overhang that prevents weather from contacting
the fireplace wall.
If local codes states a clearance greater than the one listed here, than revert
to local code clearance.
12"*

Divine Outdoor Gas Fireplace
Page 7
XG0150 - 140707.2
InstallationInstallation
Section:
Important
If the Optional drain pan is not used during construction; (as shown
in Figure 2a above) ensure any water build-up can escape to the
exterior of the finished enclosure.
Water penetration can occur, and accumulate in the base of the
fireplace, and if not taken into consideration can cause deterioration
of materials, and may cause premature failure of the structure.
Clearances
H34VON H38VON H42VON
Mantel 12"12" 12"
Shelf* 9" 9" 9"
* Dimension plus height of shelf.
Clearances
The Divine Outdoor VO clearances to combustible materials are listed
below and are the minimum clearances to combustibles that apply
to the following dimensions:
Figure 3. Minimum Corner framing dimensions.
When installing a shelf over the top of the fireplace, the minimum
clearance from the top of the fireplace to a shelf is 9".
When raising the hearth, the minimum clearance from the top of the
fireplace to a combustible ceiling is 36".
Figure 2b. Framing for shelves over the fireplace.
Warning:
When covering the upper metal portion of the fireplace with a non-
combustible material Please Note: The decorative facing materials
may be subject to temperatures in excess of 250° F. This should be
considered when selecting facing materials.
Please be aware; temperatures over the mantel will rise above normal
room temperature and walls above fireplace may be hot to touch.
We recommend careful consideration be given to the effects of elevated
mantel temperatures which may be in excess of product design, for
example: candles, plastic or pictures.
9"
H
FE
G
Mantel
Shelf

Divine Outdoor Gas Fireplace
Page 8 XG0150 - 140707.2
InstallationInstallation
Combustible facing
Non-combustible facing
(allowed over face)
Combustible
header
3"
45°
5½"
Clearances
H34VON H(L)38VO H42VON
Top 9" 9" 9"
Header 5½" 5½" 5½"
Sides 1"†1"†1"†
Floor 0" 0" 0"
Back 1"†1"†1"†
Mantel 12" 12" 12"
Ceiling 36" 36" 36"
Figure 3b. Non-combustible surrounds and sidewall clearances.
Figure 3a. Non-combustible facing Material
Finishing Around the Fireplace
All fireplace facing must be non-combustible. Non-combustible
mantels and mouldings may be safely installed over the top and on
the front of the fireplace provided that they do not project beyond
shaded area shown in Figure 3. Side wall clearances are 3". Only
non-combustible surrounds may be installed around and on the facing
of the fireplace as shown in Figure 3b.
Fireplace Facing
When selecting the finish material for your fireplace, it is important to
remember the following: THE LOWER GAS CONTROL PANEL MUST
NOT BE OBSTRUCTED IN ANY WAY - to do so restricts the air supply
for the control compartments and heat exchanger it also prevents
access for servicing controls.
Decorative facing must not extend past the fireplace opening at all,
because it will interfere with the access to retainers for removal of
glass door.
Mantels & Surrounds
NOTE: National Canadian Gas Association mantel test requirements
are for fire hazard prevention to combustible materials.
New technology, to meet consumer and government demands for the
wise use of energy, has prompted us to manufacture many models of
fireplaces which are hot, fuel and energy efficient.
WARNING:
When this appliance is installed directly on any combustible
material other than wood flooring, it must be installed on a
metal or wood panel extending the full width and depth of
the appliance.
* Shaded area must be non-combustible.
Either Montigo supplied nailing flange, and
cement board or other equivalent
non-combustible material.
123456789101112
1
5
11
15
2
6
12
16
3
9
7
13
17
18
19
20
4
10
8
14
Vertical Height (In.)
Horizontal Run (In.)
Combustible header @
5½" above top of unit
Non-combustible facing
(on face of the unit
permitted, stop short
of the opening to avoid
interfering with the screen)
Non-combustible facing
Top of screen
Combustible facing material
Combustible construction
allowed in shaded area
Figure 3. Non-combustible mantles and facings.
†Clearance to insulation jacket is 0"

Divine Outdoor Gas Fireplace
Page 9
XG0150 - 140707.2
InstallationInstallation
Section:
Section 4: Wiring
WARNING!
Montigo Part No. #RPOVO must be encased in a water-tight
electrical box OR ensure the box is installed in a dry location and
avoid any moisture. If installed outdoors, ensure you also install
a Ground Fault Interrupt per local code.
Installing The Remote Switch
The Divine Outdoor's gas valve, located behind the lower trim, may
be connected to a wall switch. The valve generates its own power on
a millivolt circuit. Use only low voltage wire, and DO NOT connect
any external power to it.
Refer to Figure 4 for wiring requirements.
Note: The switch location must not exceed 30' from the fireplace.
Figure 4. Wiring for the Divine Outdoor VO Honeywell gas control and pilot.
Figure 4a. Standing Pilot Diagram
Honeywell (Q3450)
Pilot Assembly
Pilot Electrical
Harness Connector
Honeywell Gas
Control (SV9501M)
Gas Control
Connector
Wall
Switch
Water tight
Electrical box
White
Black
Source 110V
Distribution
Panel
Power
Generator
Wall Switch
Manifold Pressure
Test Connection
Inlet Pressure
Pilot Adjsutment Screw

Divine Outdoor Gas Fireplace
Page 10 XG0150 - 140707.2
InstallationInstallation
Section 5: Installing the Gas Line
Note: After gas line is connected, each appliance
connection,valve and valve train must be checked
while under normal operating pressure with either a liquid
solution, or leak detection device, to locate any source of
leak. Tighten any areas where bubbling appears or leak
is detected until bubbling stops completely or leak is no
longer detected. DO NOT use a flame of any kind to test
for leaks.
WARNING!
When pressure testing the fireplace, Gas line, and input system
follow the appropriate local codes or your area. DO NOT connect
the fireplace to pressures in excess of 1/2lb. This will damage
the gas control valve.
The manifold outlet pressure is set from the factory to the
appropriate pressure but should be verified.
To check pressures, control valves have a provision to remove
a 1/8” N.PT. plug to be fitted with a hose barb.
Montigo requires a service shut off valve be located in an
accessible location to isolate the gas supply.
Only install gas shut-off valves approved for use by the state,
province, or other governing body in which the fireplace is
being installed.
Section 5-3: GAS CONNECTION
See Figure 5 below for location of gas line access.
Flexible gas connectors must not exceed 3 feet in length,unless
allowable within local regulations.
Connect incoming gas line to the 1/2"or 3/8" gas inlet port.
Purge all air out of gas line.
Check appliance connection,valve and valve train under normal
operating pressure with a commercially available leak check
solution.
DO NOT USE A FLAME OF ANY KIND TO TEST FOR LEAKS.
Figure 5. Gas line access.
Gasline Access
0.875” dia.
7”
to center
2”
Section 5-1: FUEL CONVERSION
Verify that your fireplace is compatible with your available gas
type. (Natural Gas or Propane shown by "N" or "L" in your
model number
If gas type is not compatible, contact your local Montigo
representative to purchase a conversion kit.
Conversion kits must be installed by a qualified service
technician.
Section 5-2: GAS PRESSURE
Optimum appliance performance requires proper input
pressures.
Gas line sizing requirements will be determined in ANSI Z221.3
National Fuel Gas Code in the USA and CAN/CGA B149 in Canada.
Pressure requirements are:
Gas Pressure Natural Gas Propane
Minimum inlet pressure 5.5in. w.c. 11in. w.c.
Manifold pressure 3.5in. w.c. 10in. w.c.

Divine Outdoor Gas Fireplace
Page 11
XG0150 - 140707.2
InstallationInstallation
Section:
Section 7: Installing & Removing the Door
Removing the door:
The Divine Outdoor VO doors are removed in a few simple steps.Follow
these below to remove the Horizontal access panel, unlatch the door
buckles and, remove the door. Replace in reverse order.
Remove the Horizontal Access Panel:
Figure 7a. Locate the door buckles. (Both Sides Typical)
Door Latch Hook
Door Latch Slot
Hand-hold
Release the Door Buckles
Figure 7. Removing and installing the Horizontal Access Panel
Locate the Door Buckles:
Figure 7b. Door buckle Tool
1
Step 4:
Firmly grasp hand-hold
end of Door buckle tool
and place the machined
end in the slot under door
frame. (as shown)
Figure 7c.
Step 2:
Step 3:
Step 1:
Remove the Horizontal cover
by placing fingers in both fin-
ger holes, then pushing away
from you and lifting out. Place
it aside during maintenance or
cleaning.
Install in reverse order.
Installed Gas
Valve Cover
Finger Holes
Remove the Horizontal Access Panel:
To install the door, hook the top edge of the door frame into place.
Lower the door into position and follow the previous steps shown in
reverse order.
Installing the Door:
2
Step 5:
Ensure the tool is firmly
in the lower end of the
slot, (as shown), Then pull
toward you (Caution: hold
the tool securely).
3
Step 6:
Pull hard if necessary to
release the spring ten-
sion. (Caution: The latch
springs back with force,
hold the tool securely).
4
Step 7:
Remove the tool from
the latch slot. Ensure the
latches are hanging freely,
the hook end is released
from the bottom of the
door. (Repeat all 4-steps
for the remaining latches).
Figure 7d.
Figure 7e.
Figure 7f.
Step 8:
Grasp the Door on either side, usually midway and lift upward, lift
the door carefully up and away from the front of the fireplace.See
Figures 7g. Place the Door aside in a safe place while
maintenance and / or cleaning is being performed.
Figure 7g. Removing and installing the glass doors. (Both
Sides Typical)
Removing the Door:

Divine Outdoor Gas Fireplace
Page 12 XG0150 - 140707.2
InstallationInstallation
Section: Section 8: Installing the Accessories
Top Left Log
Fireplace Base
Notch
Top Right Log
Embers
Embers Embers
Top Right Log
Fireplace Base
Front Lef t
Base Log
Front Right
Base Log
Notch
Notch
Fireplace Base
Rear / Bottom Log
Notch in Log
Log stand
Log stand
Pilot Assembly
Fireplace Base
Air Inlets
Installing the H34VON Log Set
Installing the Logs:
The H34VON fireplace is supplied with five ceramic fibre logs. Unpack
the logs and handle them very carefully.
Step 1.Remove the glass door as described in the previous instruction.
Figure 8a. H34VON*'s Fireplace Base.
Figure 8b. Bottom/Rear log placement.
Figure 8d. Top Left log placement.
Figure 8e. Top right log placement.
Step 6. Start the fireplace. If the flame appears satisfactory, replace
the glass door. If the flame does not appear satisfactory,
double-check the air inlet and exhaust outlet pipe to ensure
that they are unobstructed.
Step 4. Place the top left log as shown in figure 8d.A flat area is
provided on the front left log, and a notch in the Rear bottom log, as
shown in figure 27c. Install the glass door. If the flame does not
appear satisfactory, double-check the air inlet and exhaust outlet
pipe to ensure that they are unobstructed.
Figure 8c. Front base logs placement.
Step 2.Install Bottom Rear log as shown in Figure 8b.
Step 3.Install Both front base logs, (Figure 8c) on the log stands
provided. See Figure 8b.
Step 5. Place the top right log as shown in figure 8e.A notch is
provided on the front right log, and a impression in the Rear bottom log.
Figure 8f. Placing Embers.
Step 7. Place the Embers as shown in figure 8f. Arrange the ember
chips on top of the burner tray. Care should be taken when placing the
embers, as blocked burner ports may cause an incorrect flame pattern,
carbon deposits and delayed ignition. Also, the embers must never be
placed in a way that obstructs any of the air inlet ports, located at the
rear of the burner, as shown in figure 8a.
If logs are not placed properly, excessive sooting will result.
NOTICE

Divine Outdoor Gas Fireplace
Page 13
XG0150 - 140707.2
InstallationInstallation
Section:
Figure 9f. Front Left Log, (Log F).
Installing the Log set:
The H38VON are supplied with a six ceramic fibre log logset. Unpack
the logs and handle them very carefully.
Step 1.Remove the glass door as described in the previous Instructions.
Air Inlets
Pilot Assembly
Fireplace Base
Rear / Bottom Log
Notch in Log
Log A
Air Inlets
Fireplace Base
Log D
Figure 9c. Top Left Log, (Log D).
Air Inlets
Fireplace Base
Log E
Step 5. Place Front Left log (Log D) as shown in figure 9c.
Figure 9e. Top Right Log, (Log E)..
Step 6. Place Front Right log (Log E) as shown in figure 9e.
Fireplace Base
Log F
Air Inlets
Fireplace Base
Log C Log B
Step 7. Place Front Left log (Log F) as shown in figure 9f. Set notch
in lower end of Log F against stile on Log Grate.
Figure 9g. Completed Logset.
Figure 9a. Bottom Rear Log, (Log A).
Step 2.Place the bottom Rear log (Log A) as shown in figure 9a.
Figure 9b. Left front Log, (Log C) and Right front Log,
(Log B).
Step 3. Place the bottom Right log (Log B) and bottom Left Log, (Log
C) as shown in figure 9b.
If logs are not placed properly, excessive sooting will result.
NOTICE

Divine Outdoor Gas Fireplace
Page 14 XG0150 - 140707.2
InstallationInstallation
Section:
Installing the Log set:
The H42VON* is supplied with a seven ceramic fibre log logset.Unpack
the logs and handle them very carefully.
Top
Right Log
Top Right
Log
Align Pins
Align Pins
Top
Left Log
Top Left
Log
Notch in Log
Pilot Assembl y
Fireplace Base
Rear / Bottom Log
Notch in Log
Figure 10b. Placing Bottom Right / Left Logs.
Step 3.Place the bottom Right and Left logs as shown in figure10b.
Figure 10c. Top Left / Right Log.
Step 5.Place the Centre Front log , Figure 10d below, as shown
using the notch cast in the Bottom Rear log as shown in figure
10c above.
Right Fr ont
Log
Gr oove
in Log
Rest Log
Center Front Log
Centerline of Fireplace
Align
Bottom Left Log
Air Inlets
Align
Bottom Right Log
Fireplace Base
Place Embers in this ar ea
Step 4.Place the Top Right log as shown in figure 10c. using the
(4) four alignment pins protruding from the top of the Right and Left
Bottom Logs, as shown in figure 10c. With these pins align the Top
Right and Left logs using the predetermined alignment holes cast into
the underside of the logs, as shown above, figure 10d.
Step 2.Place the bottom Rear log as shown in figure 10a.
Figure 10a. Placing Bottom Rear Log.
Step 1.Remove the glass door as described in the previous Instructions.
Figure 10d. Placing Centre Front Log.
Step 7.Place the Right Centre log as shown in figure 10e.
Step 8.Place the Right Center log as shown using the notch in the Top
Right log as a guide, figure 10f.
Figure 10e. Placing Right Center Log.
Figure 10f. Placing Embers.
Step 9.Place the Embers as shown in figure 10f.
Arrange the ember chips on top of the burner tray. Care should be
taken when placing the embers, as blocked burner ports may cause
an incorrect flame pattern, carbon deposits and delayed ignition. Also,
the embers must never be placed in a way that obstructs any of the air
inlet ports, located at the rear of the burner, as shown in figure 10b.
If logs are not placed properly, excessive sooting will result.
NOTICE

Divine Outdoor Gas Fireplace
Page 15
XG0150 - 140707.2
InstallationInstallation
Installing the Firestones:
N.G. & Propane. Fireplaces
Propane HL38VOL* Fireplaces, has the option of installing the optional
cultured rocks or firestones.As described below,CAUTION,the firestones
or cultured rocks cannot cover the burners. Doing so produces an
undesirable / uneven flame pattern, and eventual sooting. Install as
shown, Figure 11 to 11a.
Screen Dimensions
Figure 11.Completed firestone installation. (Note: DO
NOT place ANY firestones on top of the burners).
Figure 11a.Operating gas fireplace with firestones sur-
rounding burner tray.
CAUTION!
DO NOT COVER THE BURNERS with firestones
Screen Dimensions
A B C D E F G
H34VON 31¼"33⅞" 29" 19⅜" 1⅜" 2⅜" 23"
H38VON 35¼"37⅞" 33" 21½" 1¼"2⅜" 25¾"
H42VON 39½" 42" 37¼"25⅜" 1¼"2⅜" 28⅞"
A
B
C
G
D
F
E

Divine Outdoor Gas Fireplace
Page 16 XG0150 - 140707.2
InstallationInstallation
Section:
Step 1). The RTSCH**VO Screen Installation Kit con-
tains two mounting brackets. One for each side of the
Screen Assembly.
Step 2). The lower portion of the mounting brackets can
be identied by the small cutout and brass nutsert. The
top contains a tab which is used for aligning the bracket.
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Step 3). Align the cutout on the bottom of the left bracket
with the lower, left corner of the replace.
Installing the Screen
Step 4). Align the tab on the top of the left bracket so
that it is ush with the outer edge of the replace.
Bottom
Top
Left
Right
Tools Required
• Drill / Driver
• Phillips Screwdriver
• ¼" Hex driver
• ⁄" drill bit (Optional)

Divine Outdoor Gas Fireplace
Page 17
XG0150 - 140707.2
InstallationInstallation
Section:
Step 5). Insert three self drilling screws on the left side
using the predrilled holes in the mounting brackets as a
guide. Repeat for the right side. It is possible to predrill
the holes using a 1/8" drill bit if preferred.
Figure 7.
Figure 8.
Figure 9.
Figure 10.
Step 6). Hang the Screen Assembly on the top of the
brackets.
Figure 11.
Step 7). Secure the bottom of the screen using two stain-
less steel machine screws provided.
Step 8). Reverse steps 6 and 7 to remove screen.

Divine Outdoor Gas Fireplace
Page 18 XG0150 - 140707.2
InstallationInstallation
Section:
Figure 12.
Figure 13.
Step 1). Remove the screen (see Section 1: Screen
Installation)
Removing the door with the screen kit installed:
Step 2). Detatch the lower portion of the door using door
latches and tilt outwards (See Fireplace Installation &
Maintenance Manual for further information.
Figure 14.
Step 3). Pull the top of the door away from the re box.
Slide the door up to clear the screen mounting brackets.
WARNING
When reinstalling door(s), always make sure all door
buckles are properly hooked and fully engaged.
Ensure that all power to the appliance is off at the electrical breaker or fuse
before beginning installation. Ensure gas is turned off at the shutoff valve before
beginning installation.
CAUTION
WARNING
When installing the replace - gas lines, ttings, accesso-
ries or any other objects cannot impede the proper
movement of the door buckles.
Young children should be carefully supervised when they are in the same
room as the applicance. Toddlers, young children and others may be
susceptible to accidental contact burns. A physical barrier is
recommended if there are at risk individuals in the house. To restrict
access to a replace or stove, install an adjustable safety gate to keep
toddles, young children and other at risk individuals out of the room and
away from hot surfaces.
CAUTION
The exhaust discharge from the front top of the appliance and all
material contacted by the exhaust are very hot and should not be
touched.
The Screen Barrier will reduce the risk of burns from contact with the
glass.
DANGER

Page 19
Divine Outdoor Gas Fireplace
XG0150 - 140707.2
OperationOperation
Section 9: Start-up Sequence with Continuous Pilot
To Turn O Gas To Appliance:
1. Turnreplaceousingwallswitchorremotecontrol.
2. Locatethegascontrolbehindthelowertrim,oronthe
rearleftside(onCaststoves).
3. Pushingascontrolknobslightlyandturn
clockwiseto"O".Donotforce.
4. Turnincominggascontrolvalvetoo
withAmericanFlameElectronicIgnition
For Your Safety - READ BEFORE LIGHTING:
Lighting Instructions:
C. Useonlyyourhandtopushinorturnthegascontrol
knob.Neverusetools.Iftheknobwillnotpushinor
turnbyhand,don'ttrytorepairit.Callaqualiedservice
technician.Forceorattempttorepairmayresultinare
orexplosion.
D. Donotusethisapplianceifanyparthasbeenunder
water.Immediatelycallaqualiedservicetechnician
toinspecttheapplianceandtoreplaceanypartofthe
controlsystem,andanygascontrolwhichhasbeen
underwater.
A. Thisappliancehasapilotwhichmustbelitbyhand.
Whenlightingthepilot,followtheseinstructionsexactly.
B. BEFORELIGHTINGsmellallaroundtheapplianceareafor
gas.Besuretosmellnexttotheoorbecausesomegas
isheavierthanairandwillsettleontheoor.
 WhatToDoIfYouSmellGas:
• Donottrytolightanyappliance.
• Donottouchanyelectricalswitch;donotuseanyphone
inyourbuilding.
• Immediatelycallyourgassupplierfromaneighbour's
phone.Followthegassupplier'sinstructions.
• Ifyoucannotreachyourgassupplier,calltheFire
Department.
1. STOP!Readthesafetyinformationaboveonthislabel.
2. Locatethegascontrolbehindthelowertrim,oronthe
rearleftside(onCaststoves).
3. Pushingascontrolknobandturnclockwise to
"OFF."
4. Waitve(5)minutestoclearoutanygas.Smellforgas,
includingneartheoor.Ifyousmellgas,STOP!Follow"B"
inthesafetyinformationaboveonthislabel.Ifyoudon't
smellgas,gotothenextstep.
5. Locatepilotburner(Seeillustrationsandfollowsteps
below.
6. Turnknobongascontrolcounterclockwise to
"PILOT."
7. Pushingascontrolknobcompletelyandhold.Lightwith
PiezoIgniterbutton.Continuetoholdthecontrolknobin
forabout(1)minuteafterthepilotislit.Releasetheknob
anditwillpopbackup.Pilotshouldremainlit.Ifitgoes
outrepeatsteps3through7.
• Ifknobdoesnotpopupwhen
released,STOP!Immediatelycall
yourservicetechnicianorgas
supplier.
• Ifthepilotwillnotstaylitafter
severaltries,turnthegascontrol
knobto"OFF"andcallyour
servicetechnicianorgassupplier.
8. Pushingascontrolknobandturncounterclockwise
to"ON."
9. Turnonremoteswitchtoignitere.
WARNING/ CAUTION: Hot while in operation. Do not touch. Severe burns
may result. Keep children, clothing, furniture, gasoline and other liquids
having ammable vapours away.
See installation and operating instructions accompanying this appliance.
Iftheinformationintheseinstructionsisnotfollowedexactly,a
reorexplosionmayresultcausingpropertydamage,personal
injuryordeath.
WARNING
P/N LB1169-11/2017
NOTE:Knobcannotbeturned
from"PILOT"to"OFF"unless
knobispushedinslightly.Do
notforce.
H
I
-
L
O
Robert Shaw Valve SIT 820 HI/LO Valve
Typicalpilotshown,see
instructionmanualfor
pilotspecictoyour
model.

 
      
A. This appliance has a pilot which is lit automatically. Do
not attempt to light the pilot by hand.
B. BEFORE LIGHTING smell all around the appliance area
for gas. Be sure to smell next to the oor because some
gas is heavier than air and will settle on the oor.
What To Do If You Smell Gas:
■ Do not try to light the appliance.
■ Do not touch any electrical switch. Do not use any
phone in your building.
■ Immediately call your gas supplier from a
neighbour's phone. Follow the gas suppliers
instructions.
1. STOP! Read the safety information above on this label.
2. Turn the replace "OFF" using the wall switch or remote
control.
3. Wait 5 minutes to clear out any gas. If you smell gas,
STOP! Follow "B" in the safety information above on
this label. If you don't smell gas, go to the next step.
4. Turn the replace "ON" using the wall switch or remote
control.
NOTE: This unit is equipped with an ignition system
that lights the pilot burner automatically. Do not
attempt to light the pilot by hand.
This unit is equipped with advanced safety
controls including pre and post purge timers.
The replace will not turn on until all of the
safety conditions are met. The fans in the
replace may operate for an extended period of
time even after the wall switch is turned off.
■ If you cannot reach your gas supplier, call the Fire
Department.
C. Use only your hand to push in or turn the gas control
knob. Never use tools. If the knob will not push in or turn
by hand, don't try to repair it. Call a qualied service
technician. Force or attempt to repair may result in a re
or explosion.
D. Do not use this appliance if any part has been under
water. Immediately call a qualied service technician
to inspect the appliance and to replace any part of the
control system, and any gas control which has been
under water.
1. Turn the replace off using the wall switch or remote
control.
2. Turn off all electrical power to the appliance.
3. Locate the gas shut off valve for the appliance and
P/N LB1170-050514







5. The wall switch LED and heat sensor LED will light up.
6. Once the predetermined airow is established in the
rebox, the ue gas switch LED will light up after 30
seconds.
7. After approximately 1 minute the hot surface igniter will
start to glow. The pilot will light up, followed by the main
burner. The replace will then start up.
NOTE: If the igniter does not glow, even after 3 minutes
have passed, follow the instructions "To Turn Off
Gas To Appliance" and call your service
technician or Montigo dealer.
Control box LED lights
turn off.
Heat Sensor /
Conmustion Air
A barrier designed to reduce the risk of burns
from the hot viewing glass is provided with this
appliance and must be installed for the protection
of children and other at-risk individuals.
HOT GLASS WILL CAUSE BURNS.
DO NOT TOUCH GLASS UNTIL
COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
DANGER

Page 20
Divine Outdoor Gas Fireplace
XG0150 - 140707.2
OperationOperation
Section 9: Start-up Sequence with Honeywell Ignition

 
      
A. This appliance has a pilot which is lit automatically. Do
not attempt to light the pilot by hand.
B. BEFORE LIGHTING smell all around the appliance area
for gas. Be sure to smell next to the oor because some
gas is heavier than air and will settle on the oor.
What To Do If You Smell Gas:
■ Do not try to light the appliance.
■ Do not touch any electrical switch. Do not use any
phone in your building.
■ Immediately call your gas supplier from a
neighbour's phone. Follow the gas suppliers
instructions.
1. STOP! Read the safety information above on this label.
2. Turn the replace "OFF" using the wall switch or remote
control.
3. Wait 5 minutes to clear out any gas. If you smell gas,
STOP! Follow "B" in the safety information above on
this label. If you don't smell gas, go to the next step.
4. Turn the replace "ON" using the wall switch or remote
control.
NOTE: This unit is equipped with an ignition system
that lights the pilot burner automatically. Do not
attempt to light the pilot by hand.
This unit is equipped with advanced safety
controls including pre and post purge timers.
The replace will not turn on until all of the
safety conditions are met. The fans in the
replace may operate for an extended period of
time even after the wall switch is turned off.
■ If you cannot reach your gas supplier, call the Fire
Department.
C. Use only your hand to push in or turn the gas control
knob. Never use tools. If the knob will not push in or turn
by hand, don't try to repair it. Call a qualied service
technician. Force or attempt to repair may result in a re
or explosion.
D. Do not use this appliance if any part has been under
water. Immediately call a qualied service technician
to inspect the appliance and to replace any part of the
control system, and any gas control which has been
under water.
1. Turn the replace off using the wall switch or remote
control.
2. Turn off all electrical power to the appliance.
3. Locate the gas shut off valve for the appliance and
P/N LB1170-050514







5. The wall switch LED and heat sensor LED will light up.
6. Once the predetermined airow is established in the
rebox, the ue gas switch LED will light up after 30
seconds.
7. After approximately 1 minute the hot surface igniter will
start to glow. The pilot will light up, followed by the main
burner. The replace will then start up.
NOTE: If the igniter does not glow, even after 3 minutes
have passed, follow the instructions "To Turn Off
Gas To Appliance" and call your service
technician or Montigo dealer.
Control box LED lights
turn off.
Heat Sensor /
Conmustion Air
A barrier designed to reduce the risk of burns
from the hot viewing glass is provided with this
appliance and must be installed for the protection
of children and other at-risk individuals.
HOT GLASS WILL CAUSE BURNS.
DO NOT TOUCH GLASS UNTIL
COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
DANGER