Montigo Proflame 2 Manual

®
C US
XG0677 141231
Proame 2
System
Operation & Maintenance Manual
Read these instructions before use.
NOTICE
FIRE HAZARD. Can cause severe injury or death. The Transmitter and IFC
.
WARNING
device causes ignition of the appliance. The appliance can turn on suddenly.
Keep away from the appliance burner when operating the remote system or
activating manual bypass of the remote system.
Property Damage Hazard. Excessive heat can cause property damage.
The appliance can stay lit for many hours. Turn off the appliance if it is not going
be attended for any length of time.
.
CAUTION
- Turn OFF the main gas supply of the appliance during installation or
maintenance of the receiver device.
- Turn OFF main gas supply to the appliance prior to removing ro reinserting the
batteries.
- In case of remote control malfunction turn OFF the IFC device using the On/Off
main switch.
- For installation / maintenance switch OFF the IFC device by removing main
power supply plug and disconnect.
ATTENTION
Do not operate in presence of water dripping, spraying, rain, etc.
WARNING
Canadian Heating Products Inc. Langley, BC V4W 4A1 | Montigo Del Ray Corp. Ferndale, WA 98248
WARNING
When installing the replace - gas lines, ttings,
accessories or any other objects cannot impede the
proper movement of the door buckles.

Page 2
Proame 2 Transmitter
XG0677 - 141231
Operation
The Proflame Transmitter 2 is an integrated part of the Proflame 2 System,
which consists of these elements:
- Proflame 2 Transmitter, to be used in conjunction with:
- Integrated Fireplaces Control (Proflame 2 IFC)
IMPORTANT
The Proame 2 Transmitter controls the
following replace functions:
1. Main Burner On/Off
2. Main Burner ame modulation (6 levels).
3. Choice of standing or intermittent pilot (CPI/IPI).
4. Thermostat and Smart thermostat functions.
5. Accent light On/Off.
6. Comfort fan speed modulation (6 levels).
The Proame 2 Transmitter uses a streamline design with
a simple button layout and informative LCD display, see
gure 1. A Mode Key is provided to index between the
features and a Thermostat Key is used to turn On/Off or
index through Thermostat functions, see gure 1 & 3.
Additionally, a Key Lock feature is provided, see gure 15.
The Proame 2 System consists of the
following elements:
1. Pilot Assembly
2. Proame Gas Valve.
3. Proame 2 Control Module
4. Wiring Harness
5. Variable Speed comfort fan *
6. Accent Lights *
7. Proame 2 remote control
8. Battery Pack (not applicable for power vented units)
9 Manual override switch
.
WARNING
Do not expose remote control to temperatures below 0°C (32°F) or above 50°C (122°F)
* Not available on all replace models. Refer to the
replace instruction guide for available features.

Page 3
Proame 2 Transmitter
XG0677 - 141231
Operation
Figure 1. Proame Remote Control
Figure 2. Proame Control Module
SW1LED1
LED2
SW1 = Programing Button
LED1 = Red Diagnostic Light
LED2 = Amber Programing Remote Control Light
Blue Back lit LCD display
On/Off Key
Thermostat Key
Up/Down Arrow Key
Mode Key

Page 4
Proame 2 Transmitter
XG0677 - 141231
Operation
Figure 3. Remote Control LCD display.
Initializing the System for the rst time
1. Install four (4) AA batteries into the battery holder
located under the rebox. (Not applicable for Power
Vented Units)
2. Install three (3) AAA batteries in the back of the remote
control, see gure 4a.
Note the polarity of batteries and install them as indicated
by the silk screen (+/-) on the holder.
3. Set manual switch to OFF position, see gure 6.
4. Connect AC Power (120 volts, 60 Hz) to replace.
Operating the System for the rst time
5. Press SW1 button on the control module. The control
module will beep three (3) times and amber LED, see
gure 2, is illuminated to indicate that the IFC is ready
to synchronize with a remote control within 10 sec. Push
the ON button. The control module will "beep" four (4)
times to indicate transmitter's command is accepted.
The System is now initialized.
Figure 4a. Remote control battery compartment.
Battery operated device. Read the battery instructions before installing them
.
WARNING
into the system. Do not expose any battery, or its holder, or a device in which
batteries are installed, to a working temperature greater than 54°C / 129°F.
Avoid battery overheating even if the working temperature of the device to which
the batteries are connected is reported to be greater than 54°C / 129°F. In case
of overheating the bad cases, develop hydrogen gas and explode.
Figure 4. Control Module Battery Pack
(Not applicable for Power Vented Units)

Page 5
Proame 2 Transmitter
XG0677 - 141231
Operation
Temperature indication Display
With the system in the "Off" position, press the
Thermostat Key and the Mode Key at the same time.
Look at the LCD screen on the Remote Control to
verify that a C or F is visible to the right of the Room
Temperature display, see gure 5 .
Turn On the Fireplace
With the system Off, turn the manual On/Off switch to on
and press the On/Off Key on the Remote Control. The
manual On/Off switch is located on the right side of the
replace under the valve blind cover. The Remote Control
display will show some other active Icons on the screen.
At the same time the Control Module will activate the
replace. A single "beep" from the Control Module will
conrm reception of the command.
Turn Off the Fireplace
With the system On, press the On/Off Key on the
Remote Control. The Remote Control LCD display will
only show the room temperature, see gure 7. At the
same time the Control Module will turn off the replace. A
single "beep" from the Receiver conrms reception of the
command.
Figure 7. Remote Control display.
Remote-Flame Control
The proame has six (6) ame levels. With the system
on, and the ame level at the maximum in the replace,
pressing the Down Arrow Key once will reduce the ame
height by one step until the ame is turned off.
The Up Arrow Key will increase the ame height each
time it is pressed. If the Up Arrow Key is pressed while
the system is on but the ame is off, the ame will come
on in the high position, see figure 8 & 9.
Figure 8. Flame Off and Flame Level 1.
Figure 9. Flame Level 5 and Flame Level Maximum.
Figure 5. Remote Control display in Farenheit & Celsius.
Figure 6. Manual On/Off Switch