MORDOMUS ENOWd User manual

ENOWd – Gateway EnOcean ® Hardware: V1.31
Firmware: V1.3
1. GENERAL FEATURE :
Reading points: 60 wireless input devices and 60 wireless
output devices.
Control: Via MD BUS e EnOcean®;
Applications: Interface etween wireless devices and
EnOcean® Mordomus;
Installation: DIN Rail.
2. GENERAL PECIFICATION :
Voltage: 12VDC;
Consumption: 70mA @ 12VDC;
torage Temperature: -10ºC to 60ºC;
Operating Temperature: 10ºC to 50ºC;
Maximum Humidity: 80%, non-condensing;
Physical pecifications:
Dimensions: 105mm X 90mm X 70mm, DIN rail mounting (6
modules); Box Plastic, self-extinguishing UL-94 V0;
Level Protection: IP20, for indoor use.
3. COMPATIBILITY :
PCCWd Compatibility: Firmware 3.42 or higher.
Mordomus oftware Compatibility: Mordomus Software
v2015.2 or higher;
4. ECURITY :
Before making any connections, please read these
instructions carefully.
Never remove the plastic ase from DIN rail.
5. CONNECTION :
Thickness of conductors:
Bus Circuit:
CAT6 Ca le F/UTP shielded, twisted;
Power circuit:
Mono-wire or multi-wire at least 0.75 mm²
Table of Connections:
Number Function
1 GND
2 MD BUS Inputs A
3 MD BUS Inputs B
4 GND
5 MD BUS Outputs A
6 MD BUS Outputs B
14 GND
15 +12VDC
16 GND
17 +12VDC
Connect the 12VDC:
The use of Mean-Well, DR60-12 or DR30-12 power supplies
is recommended.
Connect the Bus:
To connect the BUS, must e used a pair-Interlace CAT6
ca le. For example, Green for A and Green/White for B,
The shield should e connected to GND.
If the module is the last module at Mordomus Bus, the
jumpers must e placed according to Fig 1 ) to close the
BUS chain. In other situations it should remain as in Fig 1 a).
Manual: ENO-1642-EN www.mordomus.com Page 1/2

ENOWd – Gateway EnOcean ® Hardware: V1.31
Firmware: V1.3
6. ADDRE ING AND CONFIGURATION:
Before you can address the ENOWd you will have to enter the
license card supplied with the module into the Mordomus
software.
The ENOWd is ready to e addressed when Led D2 is on.
To assign the desired address to the module proceed as
following:
1. Open the "Registering Modules" window at
Mordomus software.
2. Remove the module cover loosening the housing
screws y means of a PH1 tool.
3. Press (Addressing) utton inside the module. The
4. D2 Green LED will flash slowly and the D4 Red LED
will pulse once. Note that after three minutes without
having assigned a new address, the module
automatically returns to normal mode.
5. Define the desired address at Mordomus software at
the displayed window.
Repeater: When active, all EnOcean telegrams that have not
yet een repeated y another repeater, will e forwarded y
ENOWd. (Level Repeater 1).
To ena le or disa le the repeater, press and hold the utton
Addressing for more than 3 seconds. When LED D5 is lit the
repeater is ena led, and when D5 is off the repeater is also
off. This configuration is automatically stored in non volatile
memory.
7. FUNCTIONING:
Code of Leds:
D2 Green LED:
Access - Module powered and registered;
Briefly pulse - Module receiving data y Bus Mordomus;
Intermittent - Module waiting address.
D4 Red LED:
Brief pulse - Module receiving data y Bus Mordomus.
Pulse 10 in 10 seconds - Module waiting registration.
D3 Green LED:
Briefly pulse - Module to receive wireless data;
D5 Red LED:
Briefly pulse - Module to send wireless data.
Reset: To perform a reset to the module, cut power supply
12VDC for a few seconds or place the jumper according to
Fig 2 ) for a out 3 seconds and put it ack in its original
position Fig 2 a).
Manual: ENO-1642-EN www.mordomus.com Page 2/2