Morphy Richards 47060 User manual

10/12 cup filter coffee maker
Please read and keep these instructions
Models Covered
47060- Manual Interface 47062- Manual Interface & Thermal carafe
47061- Digital Interface 47063- Digital Interface & Thermal carafe
Getting the best from your new coffee maker...
Warning: Hot water and steam
Safety first
Caution must be used when handling hot water,
coffee or steam.
Run water through your machine before first use
It is important to run water through your coffee maker
in order to rinse the machine. You can also run water
through to warm your coffee machine.
Descale as appropriate for the hardness
of the water in your area
It is important to descale as the performance of your
coffee maker may be impaired by limescale and other
impurities in the water supply.
CM47060 Rev2
For replacement parts, help with using your Morphy Richards product,
problems and lots more, contact us by phone or through our website.
UUKKHHeellpplliinnee::0088770000660022661100
RReeppllaacceemmeennttppaarrttss::0088770011667766664411
IIrreellaanndd11880000440099111199
47060 rev2 25/6/07 12:37 Page 1

UUKKHHeellpplliinnee0088770000660022661100RReeppllaacceemmeennttPPaarrttss0088770011667766664411IIrreellaannddHHeellpplliinnee11880000440099111199
Important safety
instructions
The use of any electrical
appliance requires the following
common sense safety rules.
Primarily there is danger of injury
or death and secondly the
danger of damage to the
appliance. These are indicated in
the text by the following two
conventions:
WARNING: Danger to the
person!
IMPORTANT: Damage to the
appliance! In addition we offer
the following safety advice.
Location
• Remove all the packaging and
retain for future reference.
• Ensure the coffee maker is used
on a firm, flat surface.
• Do not use the coffee maker
outdoors or in a bathroom.
• Do not place the coffee maker
on a highly polished wooden
surface as damage may occur
to the surface.
• Do not place the coffee maker
on or near hot surfaces such as
a hot plate, radiant rings or near
a naked flame.
•WWAARRNNIINNGG::DDoonnoottppllaacceetthhee
ccooffffeeeemmaakkeerroonnttooaammeettaall
ttrraayyoorrmmeettaallssuurrffaacceewwhhiillsstt
iinnuussee..
Other safety
considerations
• Disconnect the coffee maker
from the mains supply when
filling, cleaning or not in use.
• When unplugging, turn any
control to ‘OFF’, then remove
the plug from the wall socket.
• Keep the outside of the coffee
maker area clean and dry at all
times.
• Do not touch hot surfaces.
Always use handles or knobs on
the coffee maker.
• Do not immerse the coffee
maker itself in water and always
ensure the electrical
connections are kept dry.
• Do not operate any appliance
with a damaged cord or plug or
after the appliance malfunctions
or has been damaged in any
manner. Ring the helpline
number for advice on
examination and repair.
• The use of attachments or tools
not recommended or sold by
Morphy Richards may cause fire,
electric shock or injury.
• Do not use the coffee maker for
anything other than its intended
purpose.
• If the supply cord is damaged, it
must be replaced by the
manufacturer, it’s service agent
or similarly qualified persons in
order to avoid a hazard.
Product safety
• Never use warm or hot water to
fill the water reservoir.
• Do not overfill the water
reservoir.
47060 rev2 25/6/07 12:37 Page 2

2233UUKKHHeellpplliinnee0088770000660022661100RReeppllaacceemmeennttPPaarrttss0088770011667766664411IIrreellaannddHHeellpplliinnee11880000440099111199
Personal safety
• Ensure the lid of the glass
jug is securely in place
before pouring.
• Take care to pour hot
coffee slowly and carefully
without tipping the glass
jug too fast.
• Do not fill above the
capacity mark of the water
level gauge marked on the
jug.
• Do not use the glass jug in
a microwave.
• Milk should not be
reheated, only heat it when
required.
• When heating milk, please
use the stainless steel jug
provided.
• Do not fill the milk jug
above the MAX mark.
• Do not touch metal parts
until the unit has cooled.
• This appliance is not
intended for use by
persons (including children)
with reduced physical,
sensory or mental
capabilities, or lack of
experience and knowledge,
unless they have been
given supervision or
instruction concerning use
of the appliance by a
person responsible for their
safety.
Children
• Children do not understand
the dangers associated
with operating electrical
appliances. Never allow
children to use this
appliance.
• Children should be
supervised to ensure that
they do not play with the
appliance.
Treating scalds
• Run cold water over the
affected area immediately.
Do not stop to remove
clothing, get medical help
quickly.
Choice of coffee
• Choose a finely ground
espresso coffee to use with
this machine.
NOTE: Avoid blends that
are very powdery. When
the coffee is too finely
ground it may block the
filter.
ELECTRICAL
REQUIREMENTS
Check that the voltage on
the rating plate of your
appliance corresponds
with your house electricity
supply which must be A.C.
(Alternating Current).
If the socket outlets in your
home are not suitable for
the plug supplied with this
appliance the plug should
be removed and the
appropriate one fitted.
WWAARRNNIINNGG::TThheepplluugg
rreemmoovveeddffrroommtthhee
mmaaiinnsslleeaadd,,iiffsseevveerreedd,,
mmuussttbbeeddeessttrrooyyeeddaassaa
pplluuggwwiitthhaabbaarreedd
fflleexxiibblleeccoorrddiiss
hhaazzaarrddoouussiiffeennggaaggeedd
iinnttooaalliivveessoocckkeett
oouuttlleett..
Should the fuse in the 13
amp plug require changing,
a 13 amp BS1362 fuse
must be fitted.
WWAARRNNIINNGG::TThhiiss
aapppplliiaanncceemmuussttbbee
eeaarrtthheedd..
47060 rev2 25/6/07 12:37 Page 3

33
Features
⁄Measuring spoon storage
area
¤Water re-fill point
‹Measuring spoon
›Filter holder and
permanent mesh filter
fiLid opening push button
flMilk frother steel jug
‡12/15 cups glass coffee
jug
·8/10 cups steel thermal
coffee jug
‚Manual interface (see
overleaf)
„Digital interface (see
overleaf)
‰Frother control
ÂMilk hot plate switch
ÊIlluminated water level
indicator
ÁCoffee strength control
ËPlug storage
ÈAnti drip
ÍLid release
ÎHot plates
44
⁄
¤
‹
Â
fi
‡/·
Ê
fl
‚/„
Product features
‰
›
fl
Á
Ë
È
Í
Í
Î
47060 rev2 25/6/07 12:37 Page 4

„DDiiggiittaalliinntteerrffaacceevveerrssiioonn
Auto keep warm indicator
ÒMilk frother device ON indicator
ÚMilk hot plate ON indicator
ÛPower ON/OFF selection push
button
ÙProgramme selection push
button
ıAuto function push button
ˆHour function push button
˜Minute function push button
¯Cup selector push button
˘Quality and brew indicator
◊Programming mode indicator
Automatic timer function
indicator
Cup selection indicator
24 hour clock
55UUKKHHeellpplliinnee0088770000660022661100RReeppllaacceemmeennttPPaarrttss0088770011667766664411IIrreellaannddHHeellpplliinnee1188000044009911119944
/2
1
1
‚ MMaannuuaalliinntteerrffaacceevveerrssiioonn
ÏFunction selector
Ì1/2 carafe indicator
Ó1 carafe indicator
ÔBrewing ON indicator
Auto keep warm indicator
ÒMilk frother device ON indicator
ÚMilk hot plate ON indicator
Milk hot plate ON pilot light
Milk frother device ON pilot light
1/2 carafe light
1 carafe light auto
Milk frother device off pilot light
Auto keep warm light
Power ON/OFF
Ï
ÌÓ

Ò
Û
Ú
Ù
¯
˘
◊
Ô
34
35
36
ı
ˆ
36
35
34

ÚÒ˜
47060 rev2 25/6/07 12:37 Page 5

6655
OPERATING THE
APPLIANCE
BEFORE USE
Before using your coffee maker
for the first time or if you have
not used it for some time, rinse
the machine by running water
through. Follow the procedure
for making coffee, without coffee
in the filter holder.
The product that you have
purchased is available in four
different versions:
• Manual version - Glass carafe
• Manual version - Thermal carafe
• 24 hour automatic timer version
- Glass carafe
• 24 hour automatic timer version
- Thermal carafe
For the complete understanding
of how to use your machine
please refer to the specific
section related to your version.
Please note not all variants are
available in all countries, please
contact your retailer for more
information.
MANUAL INTERFACE
VERSIONS ‚
Making coffee
11Press the push button fito
open the hinged lid. The lid will
automatically rise.
22Using a jug, fill the water
reservoir ¤with the required
amount of water using the level
indicator Êas a guide. Both the
jug and water level indicator are
marked in cups A.
33Spoon ‹ the required amount
of ground filter coffee into the
mesh filter ›spreading evenly.
We suggest one level measuring
spoon for every cup. Ensure the
filter is sitting properly in the
filter holder B.
44Close the lid. Ensure the lid is
closed and latched properly C,
otherwise the machine will not
function correctly.
55Slide the jug ‡/· into the
coffee maker ensuring it sits
correctly on the hot plate D.
The jug lid must be in place
during the brewing process;
otherwise the non drip valve will
not open, causing the filter to
flood.
A
B
C
D
47060 rev2 25/6/07 12:37 Page 6

77UUKKHHeellpplliinnee0088770000660022661144RReeppllaacceemmeennttPPaarrttss0088770011557766664455IIrreellaannddHHeellpplliinnee1188000044009911119966
••TThheerrmmaallCCaarraaffeeVVaarriiaanntt
Note: Thermal carafe versions
have no hot plate. Please ensure
the jug sits correctly on the base
recess.
• Ensure the jug ·lid is fully
closed by turning the lid
clockwise, this ensures the
maximum temperature is
maintained in the jug. To ensure
the coffee is kept as warm as
possible we advise you rinse
your thermal carafe in hot water
before use.
• Please note the jug lid must be
in place during the brewing
process; otherwise the non-drip
valve will not open, causing the
filter to flood.
66Select the required strength of
coffee using the strength
selector on the lid E.
77Plug the filter coffee maker in at
the wall socket and switch on,
the water gauge Êwill
illuminate. Rotate the dial Ïto
select one of the two on
positions available: 1/2 carafe or a
full carafe,Fdepending on the
number of cups required. Refer
to ‘Cup selection function’ page
11 for further information.
88The cup selection indicator
Ì/Ó and the brewing on
indicator Ôwill light up. The hot
water will start to flow through
the coffee grounds and into the
jug as coffee for you to enjoy.
••GGllaassssCCaarraaffeeVVaarriiaanntt
When the brewing process is
complete the product will
automatically switch to keep
warm; the auto keep warm
indicator will light up.
The automatic keep warm
function will keep the coffee
warm in the carafe until the
product is switched off.
The anti-drip valve Èwill
prevent any remaining coffee
dripping onto the hot plate
during serving. Ensure that the
jug is replaced on the hot plate
after serving.
We suggest consuming your
coffee within two hours, after
this time we suggest brewing
another jug of fresh coffee.
WWAARRNNIINNGG::TThheeccooffffeeeemmaakkeerr
aannddhhoottppllaatteessaarreehhoottaanndd
rreemmaaiinnhhoottffoorrssoommeettiimmee
aafftteerrsswwiittcchhiinnggooffff..
NOTE:
• Remember to turn off the
machine when you have
finished.
• Allow the unit to cool.
• Remove the permanent filter and
empty the used coffee grounds.
Wash the filter immediately and
dry thoroughly.
••TThheerrmmaallCCaarraaffeeVVaarriiaannttss
• When the brewing process is
complete the product remains
on, we recommend you switch
off your coffee maker as soon as
brewing is complete.
• The thermal carafe · will keep
the coffee warm in the jug for up
to four hours.
• The anti drip valve Èwill
prevent any remaining coffee
dripping onto the base recess
during serving.
• We suggest consuming your
coffee within two hours, after
this time we suggest brewing
another jug of fresh coffee.
••WWAARRNNIINNGG::TThheeccooffffeeeemmaakkeerr
aannddhhoottppllaatteessaarreehhoottaanndd
rreemmaaiinnhhoottffoorrssoommeettiimmee
aafftteerrsswwiittcchhiinnggooffff..
NOTE:
• Remember to turn off the
machine when you have
finished.
• Allow the unit to cool.
• Remove the permanent filter and
empty the used coffee grounds.
Wash the filter immediately and
dry thoroughly.
UUKKHHeellpplliinnee0088770000660022661100RReeppllaacceemmeennttPPaarrttss0088770011667766664411IIrreellaannddHHeellpplliinnee1188000044009911119966
E
F
47060 rev2 25/6/07 12:37 Page 7

77
DIGITAL INTERFACE
VERSIONS „
Set the clock
• When the machine is plugged
in, the display will flash 12:00
dimly.
• To set the time press the hour
button ˆand minute buttons
˜to reach the desired time.
NOTE: The clock is a 24 hour
clock.
The clock will be reset, each
time the product is unplugged
at the wall.
Making coffee
11Press the push button fito
open the hinged lid. The lid will
automatically rise G.
22Using the jug, fill the water
reservoir ¤with the required
amount of water using the level
indicator Êas a guide. Both
the jug and water level indicator
are marked in cups H.
33Spoon ‹the required amount
of ground filter coffee into the
mesh filter ›spreading evenly.
We suggest one level measuring
spoon for every cup. Ensure the
filter is sitting properly in the
filter holder I.
44Close the lid. Ensure the lid is
closed and latched properly,J
otherwise the machine will not
function correctly.
55Slide the jug ‡/· into the
coffee maker ensuring it sits
correctly on the hot plate K.
The jug lid must be in place
during the brewing process;
otherwise the non drip valve will
not open, causing the filter to
flood.
••TThheerrmmaallCCaarraaffeeVVaarriiaanntt
Note: Thermal carafe versions
have no hot plate. Please
ensure the jug sits correctly on
the base recess.
• Ensure the jug ·lid is fully
closed by turning the lid
clockwise, this ensures the
maximum temperature is
maintained in the jug. To ensure
the coffee is kept as warm as
possible we advise you rinse
your thermal carafe in hot water
before use.
• Please note the jug lid must be
in place during the brewing
process; otherwise the non-drip
valve will not open, causing the
filter to flood.
66Select the required strength of
coffee using the strength
selector on the lid L.
77Press the power ON/OFF
selection button Û. The display
lights up brightly and the cup
selection indicator will flash
showing the previous selection.
NOTE: If the machine has been
unplugged from the wall socket
since the last operation the
previous selection will be
cleared, the default setting will
be applied (1 full carafe).
88Press the cup selection button
¯to select one of the available
options, 1/2 carafe or full carafe
Mdepending on the number of
cups required. Refer to ‘Cup
selection function’ page 11 for
further information. The
selection indicator will stop
flashing, if no buttons are
pressed for 2 seconds the
machine will begin the brewing
process.
99The brewing indicator ˘will
start to illuminate from left to
right indicating that brewing is in
progress, hot water will start to
flow through the coffee grounds
and into the jug as coffee ·.
L
G
I
J
H
K
M
35
47060 rev2 25/6/07 12:37 Page 8

99
wwwwww..mmoorrpphhyyrriicchhaarrddss..ccoomm
9988
UUKKHHeellpplliinnee0088770000660022661100RReeppllaacceemmeennttPPaarrttss0088770011667766664411IIrreellaannddHHeellpplliinnee11880000440099111199
••GGllaassssCCaarraaffeeVVaarriiaanntt
When the brewing process is
complete the product will
automatically switch to keep
warm ; the brewing indicator
˘ will stop illuminating from left
to right. All segments will remain
solidly illuminated indicating the
machine is in keep warm state.
The indicator has now changed
from a brewing indicator to a
quality indicator. Refer to ‘Coffee
Quality indicator’ page 11 for
further information.
The automatic keep warm 
function will keep the coffee
warm in the carafe until the
product is switched off.
For safety reasons the coffee
maker will automatically switch
off after two hours.
The anti-drip valve Èwill
prevent any remaining coffee
dripping onto the hot plate
during serving. Ensure that the
jug is replaced on the hot plate
after serving.
We suggest consuming your
coffee within two hours, after
this time we suggest brewing
another jug of fresh coffee.
WWAARRNNIINNGG::TThheeccooffffeeee
mmaakkeerraannddhhoottppllaatteessaarree
hhoottaannddrreemmaaiinnhhoottffoorrssoommee
ttiimmeeaafftteerrsswwiittcchhiinnggooffff..
NOTE:
• Remember to turn off the
machine when you have
finished.
• Allow the unit to cool.
• Remove the permanent filter and
empty the used coffee grounds.
Wash the filter immediately and
dry thoroughly.
•TThheerrmmaallCCaarraaffeeVVaarriiaanntt
When the brewing process is
complete the product remains
on, the brewing indicator ˘will
stop illuminating from left to
right, all segments will remain
solidly illuminated, the indicator
has now changed from a
brewing indicator to a quality
indicator. Refer to ‘Coffee
Quality indicator’ page 11 for
further information.
If the coffee is to be consumed
immediately we recommend
switching off your coffee maker
as soon as brewing is complete.
NOTE: If you switch off your
coffee maker the coffee quality
indicator will turn off and reset.
The thermal carafe will keep the
coffee warm in the jug for up to
four hours.
For safety reasons the coffee
maker will automatically switch
off after two hours.
The anti drip valve will prevent
any remaining coffee dripping
onto the base recess during
serving.
We suggest consuming your
coffee within two hours, after
this time we suggest brewing
another jug of fresh coffee.
WWAARRNNIINNGG::TThheeccooffffeeee
mmaakkeerraannddhhoottppllaatteessaarree
hhoottaannddrreemmaaiinnhhoottffoorrssoommee
ttiimmeeaafftteerrsswwiittcchhiinnggooffff..
NOTE:
• Remember to turn off the
machine when you have
finished.
• Allow the unit to cool.
• Remove the permanent filter and
empty the used coffee grounds.
Wash the filter immediately and
thoroughly.
47060 rev2 25/6/07 12:37 Page 9

99
Set the automatic
timer function
NOTE: The timer function can be
set when the coffee maker is
brewing or when it is in standby.
11Press the programme button Ù.
The display will change to show
the previous set time and cup
selection flashing. If no previous
setting has been made or the
machine has been unplugged
from the socket since the last
setting the default setting will be
shown; 12:00 and full carafe.
22Select ¯the desired number of
cups that want to be brewed, 1/2
or full carafe (see cup selection
function on page 11). The cup
selector indicator will stop
flashing.
33Press the hour and minute ˜
buttons to set the desired time.
The start time will stop flashing.
NOTE: The programming mode
indicator continues to flash to
show the display is still in
programming mode.
44If the programme button Ùis
pressed again or if no buttons
are pressed within 5 seconds
the cup selection setting and the
start time are memorised.
55To activate the automatic timer
function press AUTO button ı.
• The display will change to show
the programmed time and cup
selection setting for 5 seconds.
The display will then change to
show the time, the automatic
timer function indicator will
illuminate to show the automatic
timer function is set.
• With the automatic function
activated the coffee maker will
turn on at the desired time and
start to brew the coffee.
NOTE: If the AUTO button ıis
pressed during the brewing
process the machine will switch
off and the automatic timer
function will be activated.
If setting the automatic timer
function during the brewing
process, wait until the process is
complete before pressing the
AUTO button.
66Press the AUTO button ıagain
to cancel the automatic function,
the timer function indicator will
disappear. The machine will keep
in the memory the cup selection
setting and the start time until it
is unplugged from the mains
socket.
77To change the start time and the
number of cups repeat steps
1-5.
WWAARRNNIINNGG::RReemmeemmbbeerrttooffiillll
tthheewwaatteerrttaannkkwwiitthhwwaatteerr
aannddtthheeffiilltteerrwwiitthhccooffffeeee
bbeeffoorreeaaccttiivvaattiinnggtthheeaauuttoo
ffuunnccttiioonn..
NOTE: The clock is a 24 hour
clock.
If no buttons are pressed, the
display will revert to the time
display within 5 seconds.
47060 rev2 25/6/07 12:37 Page 10