10
Multiple functionality
1
Your vacuum cleaner can easily be configured into several
different cleaning modes:
• Two configurations as a vacuum cleaner for floors and carpets.
• Handheld vacuum cleaner which can be carried with you whilst
cleaning.
• Extended reach vacuum cleaner for cleaning hard to reach places
such as high coving etc.
Set up and charging
Charge the product fully before first use.
2
Fit the battery (16). Hook the lower end of the battery into the
cleaner, then push the top of the battery firmly until it locks into
place.
The battery will not need to be removed again unless the product
reaches the end of its useful life.
Removal of battery or replacement:
If the battery needs to be removed again, slide the battery release
button (17) towards the handheld vacuum cleaner handle (6) and
pull from the top end of the battery to remove.
Only use battery number 734000-B for this product.
In extreme conditions, batteries may be subject to leakage. If
touched, wash skin with hot soapy warning. Do not try to use or
recharge the battery in this condition.
3A
Assemble the charging cradle (29) to the charging cradle base
(31). If necessary, the two parts can be separated again by
pressing the charging cradle base detach button (33), then pulling
apart. Insert the mains adaptor connector (23) into the charging
cradle charging inlet (32). Seat the vacuum cleaner into the
charging cradle, ensuring the charging cradle electrical
connectors (28) align with the handheld vacuum cleaner electrical
connectors. Connect the mains adaptor (24) to the mains supply.
3B
Alternatively (provided the unit is in the charging cradle (29)),
insert the mains adaptor connector (23) into the handheld
vacuum cleaner charging inlet (5). The connector will only fit one
way. Connect the mains adaptor (24) to the mains supply.
After the adaptor is connected, the charge indicator (8) will
illuminate within a few seconds.
4
When the battery is empty and the product is put onto charge,
one bar of the charge indicator (8) will illuminate. As the battery
charges, the second bar of the charge indicator will start to flash
and then become steady, then the third bar will start to flash.
When the illumination of all three bars is steady, the product is
fully charged. A full charge may take 4 hours.
The three bars will stay illuminated for 5 minutes and then
extinguish to save power.
If all three bars are flashing, this indicates a fault, please see
‘Maintenance - troubleshooting’.
When fully charged, the mains adaptor may be switched off and
unplugged. If unused, the batteries will remain charged for many
weeks so there is no need to keep constantly on charge.
Assembly in upright mode
5
1 Push the neck of the motorised floor brush (22) into the handheld
vacuum cleaner suction inlet (20) until it clicks into place.
2 To remove the upright handle connector hole plug (13a) from the
upright handle connector hole (13b), press the upright handle
release buttons (14) and pull the plug out.
3 Push the upright handle (3) into the upright handle connector hole
(13b).
Switching on and power settings
6
If floor vacuum cleaning in upright mode, press the upright handle
On/Off button (2).
7
If vacuum cleaning in any other mode, press the On/Off button (9).
8
Pressing either button (2 or 9) will switch the product on at MAX.
A second press will change the power to TURBO, a third press
will change the power to MIN and a fourth press to OFF. The
product may also be switched off by pressing the switch
continuously for 2 seconds.
When the product is on, one of the three power level indicator
lights (7) will illuminate to display which power setting has been
selected and the charge indicator (8) will also illuminate to show
the amount of battery charge remaining.
The MAX setting should be sufficient for the majority of cleaning
tasks. The TURBO setting will produce the best cleaning results,
but the battery charge will be used more quickly. Using on MIN
power will be sufficient for light cleaning and will extend the
usage time before the battery needs recharging.
NOTE: The motorised floor brush (22) will not rotate when the
MIN setting is chosen.
As the battery charge is diminished during use, the number of
illuminated bars on the charge indicator (8) will reduce. When the
last bar starts to flash, the battery charge is close to its minimum
limit. The product will automatically stop when the battery charge
reaches its minimum limit. The battery must then be
re-charged.
NOTE: Using the product on MAX/TURBO setting will give
approximately 15 minutes of use. Using the product on the
MIN setting will give up to 60 minutes of use in the handheld
mode. After approximately 15 minutes of continuous use on
the MAX/TURBO setting, the power will automatically reduce
to the MIN setting to prevent over-discharge of the battery.
Using in upright mode
9
Assemble the product for upright vacuum cleaning (see
‘Assembly in upright mode’).
IMPORTANT: When using the motorised floor brush (22),
never keep it in one location on the floor for an extended
period and do not leave the product running whilst standing
still. The rotating brush bar could cause damage to some
floor coverings if the floor is exposed to the rotating brush
action for a continued period of time.
10
If cleaning floors under tables, chairs or low lying furniture , press
the back saver handle button (1) to pivot the upright handle
forwards, allowing the main body to drop parallel with the floor
without you having to bend down.
