Morrell SW-UNM-8FE1GE-8POE User manual

0
SW-UNM-8FE1GE-8POE
8-Port 10/100Mbps + 1-Port Gigabit Combo POE
Unmanaged Ethernet Switch
User Manual
Ver.1.0.0

1
Table of Contents
1 Package Contents ....................................................................................................................... 2
2. Product Features ....................................................................................................................... 2
3. Switch Front Panel ..................................................................................................................... 3
4. Switch Rear Panel ..................................................................................................................... 4
5. Installing the Switch ................................................................................................................... 4

2
Congratulations on your purchase of the PoE Ethernet switch, 8-port 10/100Mbps+1-port
1000Mbps PoE Switch provides the seamless network connection.
The product is desktop design, all-metal chassis and elegant appearance. This product is
easy to install, can rack, plug and play, no management; Dynamic LED indicator to
monitor switch status and troubleshooting work. Supporting 8 10/100Mbps and 1
10/10/1000Mbps auto-negotiation ports, use store and forward technology, combined with
dynamic memory assignment, to ensure it can be distributed to each port. Flow control
ensures to prevent data packet from losing while sending and receiving.
These PoE ports(port1-port8) can automatically detect and supply power with those IEEE
802.3at compliant Powered Devices (PDs). In this situation, the electrical power is
transmitted along with data in one single cable allowing you to expand your network where
there are no power lines or outlets, where you wish to fix devices such as APs, IP
Cameras or IP Phones, etc.
1 Package Contents
Check the contents of your package for following parts:
 PoE Ethernet Switch x 1
 User's Manual x 1
 Power Adapter x 1
 Brackets x 2
 Rubber Feet x 4
If any of these are missing or damaged, please contact your dealer immediately, if
possible, retain the carton including the original packing material, and use them against to
repack the product in case there is a need to return it to us for repair.
2. Product Features
 8 × 10/100Mbps Auto-negotiation Fast Ethernet RJ45 ports with 8 port PoE function
(port1-port8)
 1 x 10/100/1000Mbps Auto-negotiation Ethernet RJ45 port (port9)
 Supports PoE power up to 30W for each PoE port
 Supports PoE power up to 120W for all PoE ports
 Supports PoE IEEE802.3af and IEEE802.3at compliant Powered Device (PD)
 Supports IEEE802.3x flow control for Full-duplex Mode and backpressure for
Half-duplex Mode
 4K entry MAC address table of the switch with auto-learning and auto-aging
 LED indicators for monitoring power, link, activity, PoE, speed
 Internal power adapter supply

3
3. Switch Front Panel
The front panel of switch includes 8 x 10/100Mbps ports and 1 x 10/100/1000 Mbps port
and LED light.
Ports
8 10/100Mbps RJ-45 Ports: designed to connect to the device with the bandwidth of 10M
or 100M.
1 10/100/1000Mbps RJ-45 port: designed to connect to the device with the bandwidth of
10M, 100M or 1000M.
There 1-8 ports of switch have PoE power supply function, the maximum output power up
to 30W each port, it can make PD devices, such as internet phone, network camera,
wireless access point work, you only need to connect the switch PoE port directly
connected to the PD port by network cable.
For legacy devices that are not compatible, the PoE port will not offer the power to this
device. This feature allows users to freely and safely mix legacy and Power over LAN
compatible devices on their network.
LED Indicators
LED Status Description
PWR ON
Power is supplied
OFF
No power
LNK
ON
A valid link is established
Blinking
Data packets received or transmitted
OFF
No link is established
PoE
ON
There is a PoE PD connected to the port, which
supply power successfully.
OFF
No PD port connect to the port.
Blinking
The power is not enough to supply PoE device to
work on.
GIGA
ON
The connection speed is 1000Mbps
OFF The connection speed is 10Mbps

4
Blinking The connection speed is 100Mbps
100M
ON A device is connected to the port
Blinking Sending or receiving data
4. Switch Rear Panel
Power
The power port is where you will connect the included power adapter.
5. Installing the Switch
This part describes how to install your PoE Ethernet Switch and make connections to it.
Please read the following topics and perform the procedures in the order being presented.
Installation method
Follow the below guide to install the switch.
 Please install the switch in a fairy cool and dry place. See the Technical Specification
for the acceptable temperature and humidity operation ranges.
 Installing the switch on a sturdy, level surface that can support its weight (at least
5KG).
 Connect the power cord to the switch and the power outlet. The distance is less than
150cm.
 Leave at least 10cm (about 4 inches) of space at the front and rear of the switch for
ventilation.
Rack-mountable Installation
The switch is rack-mountable and can be installed on an EIA-11 inch equipment rack. To
do this, first, please install the mounting brackets on the switch’s side panels(one on each
side), secure them with the included screws, and then use the screws provided with the

5
equipment rack to mount the switch on the 11 inch rack.
Step 1
Step 2
Desktop Installation
To install the Switch on desktop, simply follow the next steps:
Step 1: Attach the rubber feet to the recessed areas on the bottom of the Switch.
Step 2: Place the Switch on desktop near an AC power source.
Step 3: Keep enough ventilation space between the Switch and the surrounding objects.
Step 4: Connect your Switch to network devices.
A. Connect one end of a standard network cable to the 10/100 RJ-45 ports on the Back
of the Switch.
B. Connect the other end of the cable to the network devices such as printer servers,
workstations or routers…etc.
Step 5: Supply power to the Switch.
A. Connect one end of the power cable to the Switch.
B. Connect the power adapter to a standard wall outlet.
When the Switch receives power, the Power LED should remain solid Green.

6
www.morrelltelecom.com
[email protected]
morrelltelecom