Mosaic G-FTB-10004 User manual

32” X 25” VERONA PROPANE FIRE PIT
Model #: G-FTB-10004
Style #: FSMVPT5016
Please keep this instruction manual for future reference
Assembly Instructions
C
US
R
Customer service: [phone]
7:00 am to 12:00 am CST (daily)
Live Chat at : www.academy.com
Email: [email protected]
--------------------------------------OR----------------------------------------
Call 855-600-9294 & Email: [email protected]
(Made in China)

TABLE OF CONTENTS
•Table Of Contents …………..……………..……………..……….…1
•Warnings and Cautions …………………………..………………2-5
•Parts Diagram………………………………………………………...6
•Parts, Hardware, and Tools….……………………..………….……7
•Assembly……………………………………………………………8-10
•Lighting Operation………………………………….……..…...…11-12
•Maintenance and Storage………………………...…...….…….13-14
•Trouble Shooting……………………………………………………15
•Warranty Information……………………………………………….16
BEFORE ASSEMBLY
Verify that all parts are included with your gas fire pit BEFORE you begin assembly by
checking the Parts and Hardware List. For your convenience, some parts may be pre-
assembled or attached to heater components.
If some parts are not included, do not attempt to assemble the gas fire pit. Call the free
number on the cover page for replacement parts.
Leave hardware installed HALF-TIGHTENED on the gas fire pit during assembly until unit is
completely assembled, then finish tightening all hardware installed.
YOUR OWNER’S MANUAL
Keep and store this Owner’s Manual for future reference-It contains important instructions and
procedures for safety and maintenance.
Page 1 of 16

Read the instructions before use. This appliance must be installed in accordance with such
regulations as are enforced.
CAUTION
Installer: Leave the manual with
the user for future use.
Consumer: Please keep this
manual for future
reference.
WARNINGS AND CAUTIONS
WARNING
Do not try to light this appliance
without reading the “LIGHTING”
instructions section of this
manual.
Do not store or use gasoline or
other flammable liquids or vapors
in the vicinity of this or any other
appliance. An LP cylinder not
connected for use must not be
stored in the vicinity of this or any
other appliance. If the information
in these instruction is not
followed exactly, a fire or
explosion may result, causing
property damage, personal injury
or death.
DANGER
IF YOU SMELL GAS:
•Shut off gas to the appliance.
•Extinguish any open flame.
•If odor continues, keep away
from the appliance and
immediately call your gas supplier
or fire department.
WARNING
FOR OUTDOOR USE ONLY!
DANGER
CARBON MONOXIDE HAZARD
This appliance can produce
carbon monoxide, which has no
odor.
Using it in an enclosed space can
cause injury or death. Never use
this appliance in an enclosed
space such as a camper, tent or
building.
WARNING
Improper installation, adjustment,
alteration, service or maintenance
can cause property damage,
injury or death. Read the
installation, operating and
maintenance instructions
thoroughly before installing or
servicing this gas appliance.
WARNING
Never leave fire pit unattended
when hot or in use.
Keep out of reach of children.
Page 2 of 16

WARNING
You must provide propane gas and propane cylinder.Use astandard 20 lb.propane
cylinder only.
Use this heater only with apropane vapor withdrawal supply system. See Chapter 5of the
Standard for Storage and Handling of Liquefied Petroleum Gas, ANSI/NFPA 58.Your local
library or fire department should have this book.
The pressure regulator and hose assembly supplied with the appliance must be used.
The installation must conform with local codes, or in absence of local codes, with National
Fuel Gas Code,ANSI Z223.1.
Adented, rusted or damaged propane cylinder may be hazardous and should be checked
by your cylinder supplier.Never use a propane cylinder with adamaged valve connection.
The LP-gas supply cylinder must be constructed and marked in accordance with the
U.S.Department of Transportation (D.O.T) Specifications for LP-Gas Cylinders, or the
standard for Cylinders, Spheres and Tubes for Transportation of Dangerous Good and
Commission, CAN/CSA-B339, as applicable.
The LP-gas supply cylinder must be provided with a cylinder connection device
compatible with the connection for the appliance.
The cylinder used must include acollar to protect
the cylinder valve.
The LP-gas supply cylinder must be provided with
alisted overfill protection device(OPD).
Do not store aspare LP Gas cylinder under or
near this appliance.
Never fill the cylinder beyond 80 percent full.
For appliances designed to use a CGA No.791I
QCC connection.
Place the dust cap on the cylinder valve outlet
whenever the cylinder is not in use.
Only types of caps or plugs may result in leakage
of propane.
Note:Gas supply pressure:25 to 250 PS1.
Warnings
Page 3 of 16

WARNING
Warnings
Page 4 of 16
Never use this appliance for other than the intended use. Do not use this appliance to
prepare food.
Never use the appliance while it is raining. Always turn the appliance off when raining.
Never use the appliance if the burner is damaged. Inspect the burner before each use.
Ensure that no debris such as leaves, grass or other objects have entered or are on the
appliance. If the burner is damaged it must be replaced prior to using the appliance with a
replacement burner specified by your dealer.
Inspect the hose assembly before each use. If there is evidence of excessive abrasion or
wear, or if the hose is damaged it must be replaced prior to using the appliance with a
replacement hose assembly specified by your dealer.
Any modification to the appliance may compromise the safety of this appliance. Special
concern is as follow:
Do not bypass thermocouple safety.
Do not operate the appliance if any parts has been under water. Immediately call a qualified
service technician to inspect the appliance and replace any part of the control system and
any gas control, which has been underwater.
A leak test mush be performed annually, or if a part of the gas system is replaced.
Never use open flame to check for gas leaks. Be certain no sparks or open flames are in
the area while you check for leaks. Sparks or open flames will results in a fire or explosion,
damage to property, serious bodily injury, or death.
Keep face and body away from burner area when lighting. Ensure burner controls are in off
position. Slowly turn on the gas supply valve.
The propane cylinder is equipped with an excess flow device. Unless burners are turned off
prior to turning the cylinder on, only small flames and low heat will be achievable.
If the burner does not light within 10 seconds, turn the valve off and wait 5 minutes for any
gas to dissipate before repeating the procedure.

WARNING:
The unit is not for use with solid fuel.
The installation must conform with local
codes or, in the absence of local codes,
with the National Fuel Gas Code, ANSI
Z223. 1/NFPA 54, NFPA58 Natural Gas
and Propane Installation Code, CSA
B149.1, or Propane Storage and Handling
CODE, B149.2.
The heater, when installed, must be
electrically grounded in accordance with
local codes or, in the absence of local
codes, with the National Electrical Code,
ANSI/NFPA 70, or the Canadian Electrical
Code, CSA C22.1.
Prior to use, check for damaged parts such
as hosed, regulators, pilot or burner.
Inspect the fuel supply connection for signs
of leakage (including the hose for LP
models) before each use of the appliance.
All leak tests should be done with a soapy
solution. NEVER USE AN OPEN FLAME
TO CHECK FOR LEAKAGE.
Children and adults should be alerted to the
hazards of high surface temperatures and
should stay away to avoid burns or clothing
ignition.
Young children should be carefully
supervised when they are in the area of the
heater.
Clothing or other flammable materials
should not be hung from the heater, or
placed on or near the heater.
Warnings
Page 5 of 16
NOTE: PLEASE READ THE FOLLOWING SAFETY RULES
Any guard or other protective device
removed for servicing the heater must be
replaced prior to operating the heater.
Installation and repair should be done by
a qualified service person. The heater
should be inspected before use and at
least annually by a qualified service
person.
More frequent cleaning may be required
as necessary. It is imperative that control
compartment, burners and circulating air
passageways of the heater be kept clean.
Keep the appliance area clear and free
from combustible materials, gasoline and
other flammable vapors and liquids.
DO NOT OBSTRUCT the flow of
combustion and ventilation air.
Keep the ventilation opening(s) of the
cylinder enclosure free and clear from
debris.
The appliance shall be used only in a
well-ventilated space and shall not be
used in a building, garage or any other
enclosed area.
An appliance may be installed with
shelter no more inclusive than:
With walls on all sides, but with no
overhead cover.
Within a partial enclosure which includes
an overhead cover and no more than two
side walls. These side walls may be
parallel, as in a breezeway, or at right
angles to each other.

A
B
C
E
H
G
D
Page 6 of 16
Parts Diagram
F
I
J

Parts List
Hardware
ACover 1
B Lava Rock 13.2 lb (6kg) 1
CTable Top With Burner 1
DStand
1
E
Side Panel 2
F
Side Panel with Window 1
G
Door 1
H
Gas Tank Support 1
AA M6 X12 bolt 20
Page 7 of 16
Tools Required (Not included)
1 Phillips screwdriver
2
Front Left Stand
1
Front Right Stand
I
J

Assembly Instructions
Step 1:
Step 2:
Connect the side panel (G) and side panel with
window (H) to stands (D/E/F) using M6 nuts (AA).
Place table top with burner (C) to non-abrasive
surface. Connect the front left stand (E), front right
stand (F) and stand (D) to table top with burner
using four M6 nuts (AA).
D
F
Step 3:
Connect the gas tank support (J) to stands (D/E/F)
using four M6 nuts (AA). Tank holder must be
E
G
J
Page 8 of 16
C
H
NOTE: Place tabel top on a non-abrasive surface
or rag to prevent scratches during assembly.
opposite of the valve.

Assembly Instructions
Step 4:
Step 5:
Place the lava rock (B) into the fire bowl. Note:
Ensure no lava rock is placed on the ignition
portion of the burner. Place cover (A) on.
Note: The cover must be removed when the
burner is in operation. Wait until the burner and
lava rock cool down before installing the cover.
Slide the hinge of door (I) to front left stand (E).
I
B
A
Page 9 of 16
Burner
E

Assembly Instructions
Step 6:
Put the cylinder into the gas tank support (H), and
secure the cylinder by tightening the screw in the
gas tank support. Connect the hose and regulator
to cylinder.
The propane cylinder is sold separately. Use a
standard 20 lb. propane cylinder only.
Page 10 of 16
Igniter
Open the igniter and put the AAA battery in then
tighten clockwise.
Step 7:
H

OPERATION
Leak testing: This must be done before initial use, annually, and whenever any gas
components are replaced or serviced. Do not smoke while performing this test, and remove
all sources of ignition. See Leak Testing Diagram for areas to check. Turn all burner
controls to the off position. Turn gas supply valve on. Brush a half-and-half solution of liquid
soap and water onto all joints and connections of the regulator, hose, manifolds and valves.
Bubbles will indicate a gas leak. Either tighten the loose joint or have the part replaced with
one recommended by your dealer and have the appliance inspected by a certified gas
installer.
If the leak cannot be stopped, immediately shut off the gas supply, disconnect it, and have
the applicant inspected by a certified gas installer or dealer. Do not use the appliance until
the leak have been corrected.
DO NOT USE AN OPEN FLAME.
Page 11 of 16
Initial Lighting: When lit for the first time, the appliance emits a slight odor. This is normal
temporary condition caused by the “burn-in” of internal paints and lubricants used in the
manufacturing process and does not occur again. Simply run the main burner on high for
approximately one half hour.

OPERATION
Lighting instructions
1. Press and hold electronic igniter button.
2. Turn the burner control to the high position, press and hold. When the
burner lights, release the electronic igniter button.
3. Continue to depress the burner control knob for 30 seconds and then
release. If the flame goes out, repeat the procedure.
4. Adjust the flame to the desired height with the burner control knob.
5. If the burner will not light with the electronic igniter, hold a lit long match
or lit long butane lighter to the ignition area of the burner and continue
with step 2.
6. To shut down the burner turn the burner control knob clockwise to the off
position. Then turn the gas off at the source (propane cylinder valve).
Page 12 of 16

MAINTENANCE AND STORAGE
CLEANING AND MAINTENANCE:
To enjoy years of outstanding performance from your heater, make sure you perform
the following maintenance activities on a regular basis:
•Keep exterior surface clean.
•Use warm soapy water for cleaning. Never use flammable or corrosive cleaning
agents.
•While washing your unit, be sure to keep the area around the burner dry at all times.
If the gas control is exposed to water in any way, do NOT try to use it. It must be
replaced.
•Keep the appliance area free and clean from combustible materials, gasoline or
other flammable vapors and liquids.
•Visually check burner flames.
•At least once a year, the unit should be inspected for the presence of spiders,
spider webs or other insects.
•Air flow must be unobstructed. Keep controls, burner, and circulating air
passageways clean. Signs of possible blockage include:
Gas odor with extreme yellow tipping of flame.
Heater does NOT reach the desired temperature.
Heat glow is excessively uneven.
Heat makes popping noises.
•Spiders and insects can nest in burner or orifices. This dangerous condition can
damage heater and render it unsafe for use. Clean burner holes by using a heavy-
duty pipe cleaner. Compressed air may help clear away smaller particles.
•Carbon deposits may create a fire hazard. Clean reflector, thermocouple and
emitter screen with a dry cloth if any carbon deposits develop.
•The burner is made from stainless steel, but extreme heat and a corrosive
environment can cause surface corrosion to occur. This can be removed with a brass
wire brush. Inspect the burner at least annually for cracks, insect nests, excessive
corrosion or any other damage. If the burner is damaged, it must be replaced with a
burner specified by the manufacturer before the appliance is put into operation.
Page 13 of 16
Normal
７．５ｉｎ
１ｉｎ

MAINTENANCE AND STORAGE
During periods of extended inactivity or when transporting
•Turn the control knob to “OFF” position.
•Disconnect LP source and move to a secure, well ventilated location
outdoors. DO NOT store in a location that will exceed 125 degrees F.
•Store heater upright in an area sheltered from direct contact with inclement
weather (such as rain, sleet, hail, snow, dust and debris).
•If desired, cover heater to protect exterior surfaces and to help prevent build
up in air passages.
NOTE: Wait until heater is cool before covering.
STORAGE:
Between uses:
•Turn the control knob to “OFF” position.
•Disconnect LP source.
•Store heater upright in an area sheltered from direct contact with inclement
weather (such as rain, sleet, hail, snow, dust and debris).
•If desired, cover heater to protect exterior surfaces and to help prevent build
up in air passages.
Note: Wait until heater is cool before covering.
Page 14 of 16

TROUBLE SHOOTING
PROBLEM PROBABLE CAUSE SOLUTION
Low heat / Low flame
when valve turned to
high.
For propane-improper lighting
procedure. Ensure lighting procedure is followed carefully. The valve must be in the off position when the tank valve is
turned on. Turn tank on slowly to allow pressure to
equalize. See lighting instruction.
Burners burn with yellow
flame, accompanied by
the smell of gas.
Possible spider web or other
debris. Thoroughly clean burner venturi. See general maintenance instructions.
Burner will not light with
the igniter, but will light
with a match.
Dead battery / or installed
incorrectly.
Loose electrode wire or switch
terminal wires.
Replace with heavy duty battery.
Check that electrode wire is firmly pushed onto the
terminal on the back of the igniter. Check that the lead
wires from the module to the ignition switch ( if equipped)
are firmly pushed onto their respective terminals.
Burner will not stay lit
when control knob is
released.
Knob not being held in long
enough.
Too windy.
Lava rock or debris in ignition
area of the burner preventing
thermocouple from being fully
engulfed in flame.
Dirty thermocouple or
thermocouple connection.
Faulty thermocouple or valve.
Thermocouple mush have time to heat up-hold the knob
in for 30 seconds after the burner lights, then release.
Unit will shut down if winds are greater than 10mph
(16km/h). Either locate to different area or use when it is
less windy.
Ensure there is no lave rock or other debris in ignition
area, and that the small hole bellow the thermocouple is
unobstructed.
Clean the thermocoupleand clean the connection
between the valve and thermocouple. Ensure the
connection is properly tightened.
Replace thermocouple and / or valve.
Humming regulator. Normal occurrence on hot days. This is not a defect. It is caused by internal vibrations in
the regulator and does not affect the performance or
safety of the gas heater.
Humming regulators will not be replaced.
Valve setting at high with
low heat output.
(Rumbling noise and
fluttering blue flame at
burner surface.)
Lack of gas.
Supply hose is pinched.
Dirty or clogged orifice.
Spider webs or other matter in
venturi tube.
Propane regulator in “low flow”
state.
Check gas level in propane cylinder.
Reposition supply hose as necessary.
Clean burner orifice.
Clean out venturi tube.
Ensure lighting procedure is followed carefully. All
valves must be in the off position when the tank valve is
turned on. Turn tank on slowly to allow pressure to
equalize. See lighting instructions.
Page 15 of 16

WARRANTY
Need help?
Call our number at:
1(866)-814-0585 or 1 (888)-922-2336
e-mail us at:
[email protected]
Page16 of 16
This product has been manufactured under the highest standards of
quality and workmanship. We warrant to the original consumer purchaser
that all aspects of this product will be free of defects in material and
workmanship for one year from the date of purchase. A replacement for
any defective part will be supplied free of charge for installation by the
consumer. Defects or damage caused by the use of other than genuine
parts are not covered by this warranty. This warranty shall be effective
from the date of purchase as shown in the purchaser receipt.
This warranty is valid for the original comsuner purchaser only and
excludes industrial, commercial or business use of the product, product
damage dur to shipment or failure which results from alteration, product
abuse, or product misuse, whether performed by a contractor, service
company, or consumer. We will not be responsible for labor charges and/
or damage incurred in installation, repair or replacement nor for incidental
or consequential damage.