Motor City Wash Works 7ELECTFRFLSH016 Technical manual

© Motor City Wash Works, Inc. 48285 Frank, Wixom Michigan 48393 U.S.A. Phone: [phone] ▪ Fax: [phone]
8MANULPWRSUP008 04-14-21 www.motorcitywashworks.com 1
POWER SUPPLY DOCUMENT
600W & 1000W
Part # 7ELECTFRFLSH016
7ELECTFRFLSH017
TABLE OF CONTENTS
Warnings and Caution………………………………………………………………………………………………..Page: 1
Descriptions……………………………………………………………………………………………………………Page: 2
Support Documents…………………………………………………………………………………………………..Page: 4
Warranty……………………………………………………………………………………………………………….Page: 8
NOTE: PROVIDES FURTHER INFORMATION!
WARNING! DANGEROUS SITUATION WHICH MAY CAUSE
EQUIPMENT DAMAGE, PERSONAL INJURIES OR FATALITIES!
STOP! PRECAUTION TO TAKE TO AVOID EQUIPMENT
MALFUNCTION OR ERROR!
IMPORTANT NOTE:
DO NOT PUNCH HOLES ON TOP OF ENCLOSURE.
DOING SO WILL VOID YOUR WARRANTY!
STOP! VERIFY THE VOLTAGE BEFORE CONNECTING!

© Motor City Wash Works, Inc. 48285 Frank, Wixom Michigan 48393 U.S.A. Phone: [phone] ▪ Fax: [phone]
8MANULPWRSUP008 04-14-21 www.motorcitywashworks.com 2
DESCRIPTION – 600W
7ELECTFRFLSH016
600W GLOWASH
25A
The function of this unit is to turn on a set of lights at or below its capabilities. The output
wiring color code is printed on power supply. The incoming power source is a 3-prong
plug from a 110VAC outlet. When powering DC lights from a MCWW product located on
the back next to the enclosure is a schematic diagram for that product.
Output voltage is polarity sensitive. Positive of light must be connected to 24VDC
(+COMMON+) in panel! Negative(s) of lights must be connected to either ‘Red’, ‘Green’
or ‘Blue’ terminals in the panel.
Red: 0VDC to Red Light
Green: 0VDC to Green Light
Blue: 0VDC to Blue Light
+Common+: 24VDC
A2: CW Controller Output Neutral
(-24-120 AC/DC)
A1: CW Controller Output Hot
(+24-120 AC/DC)
8ELECPWRTFR0023
INPUT 120-240VAC\7-3.3A
OUPUT 24VDC/25A/600W OUT
10A D
UL4 89
8ELECBRKR1P0015
8ELECTNLBLK0009
TEST
DAT E
WASH WORKS
TEST ED
DATE I NIT IALS
120V MAIN DISCONN ECT
8ELECWIRLBL 0006
00 000-3 200
SERI AL NUMB ER:
www. moto rcitywas hwor ks.com
MCWW 4 8285 Frank St, Wixom MI USA
(248) 3 13-0272
8D CAL SR LTA G00 01
N
120V
CB1
24V DC +
RED
BLUE
GRE EN
Signal
OUT
Signal
IN
1234 5678 1 2345 678
Pin1:Da ta+
Pin 2:Data-
Pin 7:GND
Pin 8:GND
POW EROUT PUT
V+
CH1
(red)
CH2
(gre en)
CH3
(blue )
powersignal
VOLTAGE 12-24VDC
MAX
CURRENT
3*10A (30A)
8ELECLEDCTLR005
8ELECRLYSPS0002
01
6
4
A1 A2
24VDC
30A
14 12 11
A2 A1
A1
A2 11
12 14
EL KO
25A D
UL1077
CB2
2A D
UL 1077
CB3
8ELECTNLBLK0009 8ELECTNLBLK0009
8ELECTNLBLK0009
8ELECTNLBLK0009
8ELECTNLBLK0009
24VDC +
RED
BLUE
GREEN
24VDC - CBX
24VDC - CBX
RED BLACK GREEN WHITE
CONN ECT UP TO T HREE W HIPS O N ON E ZONE
8DCALELCWRN0001
LOSS OF PR OTECTION - Risk of Fire or E lectric Shock
To main tain overcur rent, short-c ircuit and g round-fault prote ction:
Follow instr uctions fo r selecting ove rload and short-circu it protection.
If over load or fa ult current inte rruption occur s:
Check a ll circuits and determine c ause of int erruption.
Examine all current-ca rrying co mponents, and replace if da maged.
If burnou t occurs, rep lace the comp lete overloa d relay.
Failure t o follow the se instruc tions can result in se rious injury.
A1 A2
READ Y
SIG NAL
12-240 V
AC/ DC
RED
GREEN
BLUE
+COMMON+
CR1
CR2
8ELECTNLBLK0009

© Motor City Wash Works, Inc. 48285 Frank, Wixom Michigan 48393 U.S.A. Phone: [phone] ▪ Fax: [phone]
8MANULPWRSUP008 04-14-21 www.motorcitywashworks.com 3
DESCRIPTION – 1000W
7ELECTFRFLSH017
1000W GLOWASH
41.67A
The function of this unit is to turn on a set of lights at or below its capabilities. The output
wiring color code is printed on power supply. The incoming power source is from a
dedicated 15A circuit. With 110VAC hot, a neutral and a ground. When powering DC
lights from a MCWW product located on the back next to the enclosure is a schematic
diagram for that product.
Output voltage is polarity sensitive. Positive of light must be connected to 24VDC
(+COMMON+) in panel! Negative(s) of lights must be connected to either ‘Red’, ‘Green’
or ‘Blue’ terminals in the panel.
Red (Zone 1): 0VDC to Red Light
Green (Zone 1): 0VDC to Green
Light
Blue (Zone 1): 0VDC to Blue Light
+Common+: 24VDC
Red (Zone 2): 0VDC to Red Light
Green (Zone 2): 0VDC to Green
Light
Blue (Zone 2): 0VDC to Blue Light
+Common+: 24VDC
A2: CW Controller Output Neutral
(-24-120 AC/DC)
A1: CW Controller Output Hot
(+24-120 AC/DC)
Signal
OUT
Signal
IN
12345678 12345678
Pin1:Data+ Pin2:Data- Pin7:GND Pin8:GND
POWEROUTPUT
V+
CH1
(red)
CH2
(green)
CH3
(blue)
powersignal
VOLTAGE
12-24VDC
MAX
CURRENT
3*10A (30A)
8ELECLEDCTLR005
Signal
OUT
Signal
IN
12345678 12345678
Pin1:Data+ Pin2:Data- Pin7:GND Pin8:GND
POWEROUTPUT
V+
CH1
(red)
CH2
(green)
CH3
(blue)
powersignal
VOLTAGE
12-24VDC
MAX
CURRENT
3*10A (30A)
8ELECLEDCTLR005
8ELECTNLBLK0021
32A D
UL489
8ELECBRKR1P0015
8ELECTNLBLK0009
CB1
24VDC +
RED
BLUE
GREEN
32A D
UL1077
CB2
2A D
UL1077
CB3
8ELECTNLBLK0009 8ELECTNLBLK0009 8ELECTNLBLK0 009
24VDC +
RED
BLUE
GREEN
32A D
UL1077
CB2
N
L1
8ELECTNLBLK0021 8ELECTNLBLK0021 8ELECTNLBLK0021 8ELECTNLBLK0021 8ELECTNLBLK0021
8ELECTNLBLK0009
8ELECTNLBLK0009
141211
A2 A1
A1
A2 11
1214
ELKO
8ELECTNLBLK0009
8ELECTNLBLK0009 8ELECTNLBLK0009
120V MAIN DISCONNECT
8ELECWIRLBL0006
IN 115/230VAC-17.5/10A OUT 1000W-24VDC
8ELECPWRTFR0024
TEST
DATE
WASH WORKS
TESTED
DATE INITIALS
8DCALELCWRN0001
LOSS OF PROTECTION - Risk of Fire or Electr ic Shock
To maintain overcurrent, short-circuit and ground-fault protection:
Follow instructions for selecting overload and short-circuit protection.
If overload or fault current interruption occurs:
Check all circuits and determine cause of interruption.
Examine all current-carrying components, and replace if damaged.
If burnout occurs, replace the complete overload relay.
Failure to follow these instructions can result in serious injury.
24VDC +
RED
BLUE
GREEN
24VDC - CBX
24VDC - CBX
RED BLACK GREEN WHITE
CONNECT UP TO THREE WHIPS ON ONE ZONE
8ELECRLYSPS0002
0 1
6
4
A1 A2
24VDC
30A
8ELECRLYSPS0002
01
6
4
A1 A2
24VDC
30A
RED
GREEN
BLUE
+COMMON+
RED
GREEN
BLUE
+COMMON+
PS1
A1 A2
READY
SIGNAL
12-240V
AC/DC

© Motor City Wash Works, Inc. 48285 Frank, Wixom Michigan 48393 U.S.A. Phone: [phone] ▪ Fax: [phone]
8MANULPWRSUP008 04-14-21 www.motorcitywashworks.com 4
SUPPORT DOCUMENTS
7ELECTFRFLSH016

© Motor City Wash Works, Inc. 48285 Frank, Wixom Michigan 48393 U.S.A. Phone: [phone] ▪ Fax: [phone]
8MANULPWRSUP008 04-14-21 www.motorcitywashworks.com 5

© Motor City Wash Works, Inc. 48285 Frank, Wixom Michigan 48393 U.S.A. Phone: [phone] ▪ Fax: [phone]
8MANULPWRSUP008 04-14-21 www.motorcitywashworks.com 6
7ELECTFRFLSH017

© Motor City Wash Works, Inc. 48285 Frank, Wixom Michigan 48393 U.S.A. Phone: [phone] ▪ Fax: [phone]
8MANULPWRSUP008 04-14-21 www.motorcitywashworks.com 7

© Motor City Wash Works, Inc. 48285 Frank, Wixom Michigan 48393 U.S.A. Phone: [phone] ▪ Fax: [phone]
8MANULPWRSUP008 04-14-21 www.motorcitywashworks.com 8

© Motor City Wash Works, Inc. 48285 Frank, Wixom Michigan 48393 U.S.A. Phone: [phone] ▪ Fax: [phone]
8MANULPWRSUP008 04-14-21 www.motorcitywashworks.com 9

© Motor City Wash Works, Inc. 48285 Frank, Wixom Michigan 48393 U.S.A. Phone: [phone] ▪ Fax: [phone]
8MANULPWRSUP008 04-14-21 www.motorcitywashworks.com 10

© Motor City Wash Works, Inc. 48285 Frank, Wixom Michigan 48393 U.S.A. Phone: [phone] ▪ Fax: [phone]
8MANULPWRSUP008 04-14-21 www.motorcitywashworks.com 11

© Motor City Wash Works, Inc. 48285 Frank, Wixom Michigan 48393 U.S.A. Phone: [phone] ▪ Fax: [phone]
8MANULPWRSUP008 04-14-21 www.motorcitywashworks.com 12

© Motor City Wash Works, Inc. 48285 Frank, Wixom Michigan 48393 U.S.A. Phone: [phone] ▪ Fax: [phone]
8MANULPWRSUP008 04-14-21 www.motorcitywashworks.com 13

© Motor City Wash Works, Inc. 48285 Frank, Wixom Michigan 48393 U.S.A. Phone: [phone] ▪ Fax: [phone]
8MANULPWRSUP008 04-14-21 www.motorcitywashworks.com 14
WARRANTY AND RETURN PROCEDURE:
Motor City Wash Works warrants this product to be free of defect in material and/or workmanship for a period of
one year from the date of purchase. During the warranty period MCWW will at its discretion, at no charge to the
customer, repair or replace this product if found defective, with a new or refurbished unit, but not to include costs of
removal or installation. Any product returned to MCWW for warranty has to have a Return Material Authorization
Number. All shipping costs to MCWW are assumed by the customer. This is only a summary of the MCWW
Limited Warranty. Please, communicate with MCWW for our complete warranty.
Prior to returning any product to MCWW, the customer must call in for a Return Material Authorization Number
and a copy of our Return Material Authorization Form must be completed. The RMA number must be written
clearly on the outside of the shipping package and a copy of the form must be included in the package.