Motorline MR5 User manual

CH10V CH2
12/
24
1 2 3 4 5 6
1
ON
2
7 8
MR5 | MR6
EN
CONNECTIONS SCHEME TECHNICAL SPECIFICATIONS
Start 1
NO
Power supply Start 2
NO
Antenna
Unifilar
hard wire
antenna
ATTENTION!
Pay attention to the
jumper position
before connecting to
power
 or V
DIPPERS
JUMPER
CH2
LED CH1
LED
SEL
BOTTON
• CONNECTOR’S DESCRIPTION
01 • 12-24V AC/DC Power supply
02 • 0V Power supply
03 • CH1 contact output - NO
04 • CH1 contact output - NO
05 • CH2 Contact output - NO
06 • CH2 Contact output - NO
07 • Antenna mass input
08 • Antenna hot pole input
The MR5 – MR6 dual channel radio receiver allows to control electric and electronic devices when
coupled with one or more transmitters.
• Frequency 433,92 MHz
• Power supply 12-24V AC/DC
• Maximum consumption 5W
• Code type 12-18-32 Bit or Rolling Code
• Code memorization (CH1 + CH2) 500 Max
• Relay 30V DC 1A
• Temperature -10°C to 55°C
• Dimensions 53x82x40mm
• Range in open space 50-100m
• Protection Grade MR5 - IP 42 | MR6 - IP 54
• CHARACTERISTICS BOARD
By selecting Jumper J1 position, you can select the power supply voltage:
• JUMPERS
POSITION VOLTAGE
Pos. 1-2 12V AC/DC.
Pos. 2-3 24V AC/DC (from factory).

1
ON
2
CH1
CH2
SEL
1
ON
2
CH1
CH2
SEL
1
ON
2
CH1
CH2
SEL
MR5 | MR6
01
02
03
EN
TECHNICAL SPECIFICATIONS PROGRAMMING
MONOSTABLE DISTANCE PGM
(CH1 AND CH2) TEMP. 120 SEC. BISTABLE
The receiver can manage the two channels individually and also allows to have different functioning
modes:
Channel CH1: monostable functioning only with possibility of activation of Distance Programming.
Channel CH2: by selecting SW1 Switch, it is possible to select the following functioning modes for
channel CH2 (Distance programming mode, and monostable mode).
• CH1 (CHANNEL 1) AND CH2 (CHANNEL 2) OPERATING TYPE
RECEIVER INSTALLATION
It is very important to choose the place of installation
carefully in order for the transmitter and the receiver to
function well. Capacity is not only conditioned by the
technical features of the device, but also varies depending
on the radio-electric conditions of the place.
The receiver is provided with a local antenna. If you choose
an external antenna (for MR5), it should be positioned on
the outside, in highly visible spots and away from metal
structures.
You can not install two receivers if not respected a minimum
distance of 5 meters between them.
Installation:
01 • Fix the support on the wall.
02 • Place the board on the suport, sliding it between the
existing support ledges.
03 • Place the cover to close.
The programming of radio-controls must be performed with no antenna connected, up to a
maximum of 500 codes. When the memory is full, the CH1 and CH2 LEDs will flash quickly.
When the Led remains permanently lit, the CH1 channel programming is complete. To program CH2
you just need to, in step 1, press twice in SEL button.
Programming transmitter in channel "CH1" and "CH2":
• TRANSMITTER PROGRAMMING
01 • Press once the SEL button. 02 • The CH1 LED will start
to flash. 03 • Send a code from the transmitter to program.
If the receiver must be restored to factory configuration, press the SEL key continuously for 5
seconds. The CODE CH1 and CODE CH2 LEDs will flash three times quickly and then switch-off
indicating the operation's sucess.
• CONTROL BOARD RESET
The distance programming of radio controls is obtained by selecting Dip Switch SW1 in distance
PGM mode. In this way the receiver allows programming of the transmission code, without using
directly the SEL key.
• DISTANCE PROGRAMMING
02 • The receiver goes into
programming mode. 03 • Send a code from the transmitter to program.
01 • Continuously send
the code for 10 sec with
an already programmed
transmitter.