Motorola MBP30 User manual

USER’S GUIDE
MBP30
BABY MONITOR
USER’S GUIDE
The features described in this user’s guide are subject to
modifications without prior notice.
V 0.1

This User's Guide provides you with all the information you
need to get the most from your product.
Before you can use the baby monitor, you'll need to insert and
fully charge the battery on the Parent unit. Please read the
Safety Instructions on page 6 before you install the units.
Got everything?
• 1 x Parent unit
• 1 x Baby unit
• 1 x Rechargeable Ni-MH battery pack for the Parent unit
• 1 x Power adapter for the Parent unit
• 1 x Power adapter for the Baby unit
IMPORTANT
The non-rechargeable batteries for the Baby unit are not
supplied with your product. We recommend the batteries to be
installed before use, so that the unit continues to work in the
event of a mains power failure.
Welcome...
to your new Motorola Baby Monitor!
Thank you for purchasing the MBP30. Now you can see and
hear your baby sleeping in the other room or you can monitor
your older children in their playroom.
Please retain your original dated sales receipt for your records.
For warranty service of your Motorola product, you will need to
provide a copy of your dated sales receipt to confirm warranty
status. Registration is not required for warranty coverage.
For product related questions, please call:
US 1-888-331-3383 or Canada 905-831-6555
On the Web: www.motorola.com

1. Display
2. Menu key
3. Left key
4. Microphone
5. Down key
6. Right key
7. Up/Talk key
8. Power/Channel/Enter key
9. Power adapter connector
10. Belt clip
11. Speaker
12. Battery cover screw
13. Battery cover
Overview of your Parent unit
13
11
10
12
Parent unit menu icons
Adjust contrast level of the LCD
Turn the night vision on or off
Adjust the voice activation level
Set video timer to switch off the LCD
Pair a camera unit
9
1
2
8
3
45
7
6

2
15
3
4
Overview of your Baby unit
1. Power LED
2. Infrared LEDs
3. Light sensor
4. Microphone
5. Camera lens
6. On/Off switch
7. Speaker
6
7

Table of contents 5
ENGLISH
Table of contents
1. Safety Instructions .....................................................................6
2. Getting started ............................................................................7
2.1 Baby unit power supply ..............................................................7
2.2 Parent unit battery Installation....................................................8
2.3 Parent unit power supply............................................................9
2.4 Registration ..............................................................................10
3. Using the Baby Monitor MBP30 ..............................................11
3.1 Setting up .................................................................................11
3.2 Setting up .................................................................................12
3.3 Selecting camera channel........................................................12
3.4 Pairing camera channels..........................................................12
3.5 Night vision...............................................................................13
3.6 Talk function.............................................................................13
3.7 Adjusting the volume of the parent unit ....................................13
4. MBP30 Parent Unit Menu Options........................................... 13
4.1 Brightness ................................................................................13
4.2 Night Vision ..............................................................................13
4.3 Voice Activation........................................................................14
4.4 Video Timer..............................................................................14
5. Disposal of the device (environment)..................................... 15
6. Cleaning.....................................................................................15
7. Help............................................................................................16
8. General Information.................................................................. 16
9. Wall mounting instructions ..................................................... 25

6 Safety Instructions
1. Safety Instructions
WARNING
This baby monitor is compliant with all relevant standards regarding
electromagnetic fields and is, when handled as described in the User’s
Guide, safe to use. Therefore, always read the instructions in this
User’s Guide carefully before using the device.
• Adult assembly is required. Keep small parts away from children
when assembling.
• This product is not a toy. Do not allow children to play with it.
• This baby monitor is not a substitute for responsible adult supervision.
• Keep this user’s guide for future reference.
• Do not place the baby unit or cables in the crib or within arm's reach
of the baby (the unit should be at least 3 feet away).
• Keep the cords out of reach of children.
• Do not cover the baby monitor with a towel or blanket.
• Never use extension cords with power adaptors. Only use the
power adaptors provided.
• Test the baby monitor before use. Become familiar with its functions.
• Do not use the baby monitor near water.
• Do not install the baby monitor near a heat source.
• Only use the chargers and power adaptors provided. Do not use
other chargers or power adaptors as this may damage the device
and battery pack.
• Only insert battery pack of the same type.
• Do not touch the charger or plug contacts with sharp or metal objects.
CAUTION
Risk of explosion if battery is replaced by an incorrect type. Dispose of
used batteries according to the instructions.

Getting started 7
ENGLISH
2. Getting started
2.1 Baby unit power supply
1. Connect the small plug of the power adaptor to the baby unit and
the other end to the electrical outlet (110V/60Hz).
NOTE
Only use the enclosed power adaptor (5V DC / 500mA).
2. Slide the power switch to the ON position. The power LED will light
up in green.
3. To switch off the baby unit, slide the power switch to OFF position.

8 Getting started
2.2 Parent unit battery Installation
1. Turn the belt clip so that it is in the hanging position.
2. Loosen the screw in a counterclockwise direction using a small
screwdriver. Remove the battery cover.
3. Insert the wire tab of the rechargeable battery pack into the contact
slot as shown above and fit the battery pack into the compartment.
4. Close the battery compartment and tighten the screw in a
clockwise direction.
5. Press Fto switch ON the parent unit. The LCD screen illuminates.
- It will take a few seconds to start up the unit.
6. Press and hold Fto switch OFF the parent unit.
The battery icon indicates that the battery pack is low and needs
to be recharged. The battery pack takes about 15 hours to charge fully.
Black Red
screw

Getting started 9
ENGLISH
2.3 Parent unit power supply
IMPORTANT
We recommend the rechargeable battery pack to be installed before use,
so that the unit continues to work in the event of a mains power failure.
1. Connect the small plug of the power adaptor to the parent unit and
the other end to the electrical outlet (110V/60Hz)
NOTE
Only use the enclosed power adaptor (5V DC / 1000mA).
2. The LCD screen illuminates and starts up automatically after a few
seconds.
3. Press and hold Fto switch OFF the parent unit.
NOTE
Once the baby and parent units are switched on, the display on the
parent unit will show the video captured by the baby unit.
When there is no connection or out of range, the icon on the LCD
display will flash and the parent unit will beep continuously. Move the
parent unit closer to the baby unit until the link is re-established.

10 Getting started
2.4 Registration
The baby monitor is already pre-registered upon your purchase. You do
not need to re-register it again unless the baby unit loses its link with the
parent unit. Please check that you have selected the correct channel that
was linked to your baby unit before you attempt to re-register your unit.
To re-register your baby monitor, follow the procedure below:
1. Switch off the camera and remove the small power plug from the
camera. Then, remove the battery pack from the parent unit and
switch off the mains power.
2. When the battery pack is replaced in the Parent unit with the
mains power switched back on, the LCD screen illuminates and
starts up automatically.
3. Press Dto enter menu mode.
4. Press (or )until is selected on the LCD screen.
5. Press +or -to select the camera channel you wish to pair.
There are up to 4 camera channels available for pairing.
6. Switch on the camera and press Fon the Parent unit to start
pairing. Pairing is displayed as the Parent unit search for a camera
device.
Wait for 16 seconds for the parent unit to locate the camera and map it
to the current selected channel. The pairing is complete when the
display screen on the parent unit captures the video from the baby
unit’s camera.
If no camera is found, No Device found will be displayed on the LCD
screen. Switch the camera off and on to try again.