Motorola MBP35BL User manual

USER’S GUIDE
MBP35BL, MBP35BW
BABY MONITOR
USER’S GUIDE
The features described in this user’s guide are subject to
modifications without prior notice.

This User’s Guide provides you with all the information you need
to get the most from your product.
Before you can use the baby monitor, you’ll need to insert and
fully charge the battery on the Parent unit. Please read the Safety
Instructions on page 6 before you install the units.
Got everything?
• 1 x Parent unit
• 1 x Baby unit
• 1 x Rechargeable Ni-MH battery pack for the Parent unit
• 1 x Power adapter for the Parent unit
• 1 x Power adapter for the Baby unit
IMPORTANT
The non-rechargeable batteries for the Baby unit are not supplied
with your product. We recommend the batteries to be installed
before use, so that the unit continues to work in the event of a
mains power failure.
Welcome...
to your new Motorola Baby Monitor!
Thank you for purchasing the MBP35BL, MBP35BW. Now you can
see and hear your baby sleeping in the other room or you can
monitor your older children in their playroom.
Please retain your original dated sales receipt for your records. For
warranty service of your Motorola product, you will need to provide
a copy of your dated sales receipt to confirm warranty status.
Registration is not required for warranty coverage.
For product related questions, please call:
0845 218 0890 in the UK
(65) 68412668 in Singapore
On the Web: www.motorola.com

5
6
7
2
1
3 4
TALK MENU
12
11
10 9 8
13
1. Display (LCD screen)
2. Up </ Down >keys
Normal mode: Adjust
speaker volume
Menu mode: Adjust setting
3. Power and Low battery LED
4. Voice Activation LED
5. Lullaby Play/Stop key i
Press once to play lullaby.
Press again to stop playing.
6. Lullaby selection key j
Press to select a lullaby
during playback.
7. Microphone
8. Menu key m
Press to open the Menu
options
9. Talk key t
Press and hold to speak to
your baby.
10. Power key p
Press and hold to turn on/off
the unit.
11. Antenna
12. Battery cover
13. Speaker
)))
Overview of your Parent unit
Parent unit display symbols
Indicates that the Baby Unit is out of range or not linked to the
Parent Unit.
Appears when setting the Temperature mode.
High
Appears when the temperature goes above 26°C (79°F).
Low
Appears when the temperature goes below 14°C (57°F).
Appears when setting the Night Light function.
Indicates that the Talk function is activated.
Appears when the Lullaby function is activated.
Appears when adjusting the Volume of the Parent Unit.
Appears when adjusting the Brightness of the Parent Unit display.

1
2
3
4
5
9
8
7
6
Overview of your Baby unit
1. Photo sensor
2. Camera lens
3. Infrared LEDs
4. Power LED
5. Night lights
6. On/Off switch
7. Speaker
8. Antenna
9. Temperature sensor
Important guidelines for installing your Baby Monitor
• To use your video monitor baby and parent unit together, you must
be able to establish a radio link between them, and the range will be
affected by environmental conditions.
• Any large metal object, like a refrigerator, a mirror, a filing cabinet,
metallic doors or reinforced concrete, between the baby and parent
unit may block the radio signal.
• The signal strength may also be reduced by other solid structures,
like walls, or by radio or electrical equipment, such as TV's,
computers, cordless or mobile phones, fluorescent lights or dimmer
switches.
• Use of other 2.4GHz products, such as wireless networks,
Bluetooth®systems or microwave ovens may cause interference
with this product, so keep the baby monitor away from these types
of products, or turn them off if they appear to be causing
interference.
• If the signal is poor, try moving the parent and/or the baby unit to
different positions in the rooms.
Parent Unit display symbols (cont’d)
Appears when the Parent Unit is in registration mode.
VOX
Appears when setting the Voice Activation level.

Table of contents 5
ENGLISH
Table of contents
1. Safety Instructions ......................................................................... 6
2. Getting started................................................................................ 7
2.1 Baby unit battery installation...........................................................7
2.2 Baby unit power supply ..................................................................8
2.3 Parent unit battery Installation ........................................................8
2.4 Parent unit power supply ................................................................9
2.5 Registration ..................................................................................10
3. Using the Baby Monitor MBP35BL, MBP35BW ......................... 11
3.1 Setting up .....................................................................................11
3.2 Night vision ...................................................................................11
3.3 Talk function .................................................................................11
3.4 Adjusting the volume of the Parent Unit .......................................11
3.5 Playing a lullaby for your baby......................................................12
4. MBP35BL, MBP35BW Parent Unit Menu Options ..................... 13
4.1 Brightness.....................................................................................13
4.2 Temperature Display (ºC or ºF) ....................................................13
4.3 Night Light ....................................................................................13
4.4 Voice Activation ............................................................................14
5. Disposal of the device (environment) ........................................ 15
6. Cleaning ........................................................................................ 16
7. Help................................................................................................ 17
8. General Information ..................................................................... 18

6 Safety Instructions
1. Safety Instructions
WARNING
This baby monitor is compliant with all relevant standards regarding
electromagnetic fields and is, when handled as described in the User’s
Guide, safe to use. Therefore, always read the instructions in this User’s
Guide carefully before using the device.
• Adult assembly is required. Keep small parts away from children when
assembling.
• This product is not a toy. Do not allow children to play with it.
• This baby monitor is not a substitute for responsible adult supervision.
• Keep this User’s Guide for future reference.
• Do not place the baby unit or cables in the cot or within arm's reach of
the baby (the unit should be at least 1 metre away).
• Keep the cords out of reach of children.
• Do not cover the baby monitor with a towel or blanket.
• Never use extension cords with power adapters. Only use the power
adapters provided.
• Test the baby monitor before use. Become familiar with its functions.
• Do not use the baby monitor near water.
• Do not install the baby monitor near a heat source.
• Only use the chargers and power adapters provided. Do not use other
chargers or power adapters as this may damage the device and
batteries.
• For the parent unit, only insert a rechargeable battery pack of the
same type. For the baby unit, use non-rechargeable batteries and
insert with the correct polarity, as indicated in the battery compartment
and in “2.1 Baby unit battery installation”.
• Do not touch the charger or plug contacts with sharp or metal objects.
CAUTION
Risk of explosion if battery is replaced by an incorrect type. Dispose of
used batteries according to the instructions.

Getting started 7
ENGLISH
2. Getting started
2.1 Baby unit battery installation
The camera uses either 3 AA size batteries (non-rechargeable batteries
recommended) or the household power mains. The Baby unit has no
charging function!
IMPORTANT
The non-rechargeable batteries for the Baby unit are not supplied with
your product. We recommend the batteries to be installed before use, so
that the unit continues to work in the event of a mains power failure.
1. Loosen the screw in a counterclockwise direction using a small
screwdriver. Remove the battery cover.
2. Install the 3 AA non-rechargeable batteries following the polarity as
shown in the compartment. Close the battery compartment and
tighten the screw in a clockwise direction.
3. Slide the power switch to the
ON position. The power LED will light up
in green.
To switch off the baby unit, slide the power switch to the
OFF position.
NOTE
When the battery level is low, the power LED will turn orange and will flash.
WARNING
Do not mix old batteries with new ones.
Keep batteries away from small children.
Do not short-circuit batteries or dispose of in fire.
Remove the batteries if this device is not going to be used for a long
period of time.
screw

8 Getting started
2.2 Baby unit power supply
1. Connect the small plug of the power adapter to the baby unit and the
other end to the mains socket (230V/50Hz).
NOTE
Only use the enclosed power adapter (6V DC / 800mA).
2. Slide the power switch to the
ON position. The power LED will light up
in green.
3. To switch off the baby unit, slide the power switch to
OFF position.
2.3 Parent unit battery Installation
Black Red

Getting started 9
ENGLISH
1. Loosen the screw in a counterclockwise direction using a small
screwdriver. Remove the battery cover.
2. Insert the wire tab of the rechargeable battery pack into the contact
slot as shown above and fit the battery pack into the compartment.
3. Close the battery compartment and tighten the screw in a clockwise
direction.
4. Press and hold pto switch ON the parent unit.
- It will take a few seconds to start up the unit.
5. Press and hold pto switch OFF the parent unit.
NOTE
When the battery level is low, the power LED will turn orange and will
flash. Charge the battery pack for at least 15 hours before using on
battery power only.
NOTE
When the unit is powered up with either the power adapter or using the
rechargeable battery pack, the LED will light up in green. If both the
power adapter and rechargeable battery pack are used, the LED will light
up in red.
2.4 Parent unit power supply
1. Connect the small plug of the power adapter to the parent unit and
the other end to the mains socket (230V/50Hz).
NOTE
Only use the enclosed power adapter (6V DC / 800mA).

10 Getting started
2. Press and hold pto switch ON the parent unit. The power LED
will light up in green.
3. Press and hold pto switch OFF the parent unit.
NOTE
Once the baby and parent units are switched on, the display on the parent
unit will show the video captured by the baby unit. When the VOX mode
is on, the screen will turn off after a few seconds if the sound near the
baby unit drops below the Voice Activation threshold level of the unit.
When there is no connection or out of range, the icon on the LCD
display will flash and the parent unit will beep continuously. Move the
parent unit closer to the baby unit until the link is re-established.
2.5 Registration
The Baby monitor is pre-registered to your Parent Unit. You do not need
to register it again unless the Baby Unit loses its link with the Parent Unit.
To re-register your Baby Unit, or register a new Baby Unit, follow the
procedure below:
1. Switch off the Baby Unit
2. Press and hold the mbutton on the Parent Unit until
appears on the display screen.
3. Then press the mbutton to confirm the selection and enter the
registration mode.
..... will appear on the screen for up to 15
seconds.
4. Switch the Baby Unit ON to enter the registration mode. The power
LED on the Baby Unit flashes quickly for approximately 3seconds.
The registration is completed when
.....OK appears and then the
video captured by Baby Unit’s camera appears on the display screen of
the Parent Unit.
If the registration fails then
.....X appears and then both the Parent
and Baby Unit return to normal mode.
NOTE
If a particular Baby Unit had been registered already, registering this
current Baby Unit again will over-write the old registration.