Motorola CLP1013 User manual

Model CLP1013, CLP1043, and CLP1063 (with Bluetooth® Wireless Technology)
User Guide
CLP SeriesTwo-Way Radio
TM

Document Copyrights
No duplication or distribution of this document or any portion thereof shall take place without the express
written permission of Motorola. No part of this manual may be reproduced, distributed, or transmitted in
any form or by any means, electronic or mechanical, for any purpose without the express written
permission of Motorola.
Disclaimer
The information in this document is carefully examined, and is believed to be entirely reliable. However,
no responsibility is assumed for inaccuracies. Furthermore, Motorola reserves the right to make changes
to any products herein to improve readability, function, or design. Motorola does not assume any liability
arising out of the applications or use of any product or circuit described herein; nor does it cover any
license under its patent rights nor the rights of others.

CONTENTS
i English
CONTENTS
Computer Software Copyrights . . . . . . . . . iii
Radio Frequency (RF) Exposure Safety
Standards. . . . . . . . . . . . . . . . . . . . . . . . . . . iv
Product Safety and RF Exposure
Compliance . . . . . . . . . . . . . . . . . . . . . . iv
Canada Licensing Information. . . . . . . . . . .v
General Information. . . . . . . . . . . . . . . . . . . . .v
The License Application . . . . . . . . . . . . . . . . .v
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . .1
Package Contents. . . . . . . . . . . . . . . . . . . . . .1
Radio Overview . . . . . . . . . . . . . . . . . . . . . . .2
Radio Controls. . . . . . . . . . . . . . . . . . . . . . . . .2
Getting Started . . . . . . . . . . . . . . . . . . . . . . . .3
Install The Battery . . . . . . . . . . . . . . . . . . . . . .3
Connecting a Wired Audio
Accessory . . . . . . . . . . . . . . . . . . . . . . . . .4
Connecting a Bluetooth Wireless
Accessory (Select Models Only) . . . . . . . . . . .5
Adding Bluetooth Headset
(Initial Pairing) . . . . . . . . . . . . . . . . . . . . . 5
Reconnecting to Last Connected
Bluetooth Headset . . . . . . . . . . . . . . . . . . 5
Erasing Bluetooth Headset History
and Add Bluetooth Headset. . . . . . . . . . . 5
Turning the Radio On and Off . . . . . . . . . 6
Adjusting the Volume. . . . . . . . . . . . . . . . 6
Installing and Removing the Swivel
Belt Clip Holster . . . . . . . . . . . . . . . . . . . . 6
Transmitting and Receiving . . . . . . . . . . . . . . 7
Operation with Menu Settings . . . . . . . . . . . . 8
Selecting a Channel. . . . . . . . . . . . . . . . . 9
Monitoring a Channel. . . . . . . . . . . . . . . 10
Scanning . . . . . . . . . . . . . . . . . . . . . . . . 10
Dynamic Talkaround Scan (*) . . . . . . . . 11
Sending Call Tone (enabled through
CPS) . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Mute Feature (*). . . . . . . . . . . . . . . . . . . 11
Talk Permit Tone (*). . . . . . . . . . . . . . . . 11
Battery and Charger Features. . . . . . . . . . 12
Battery Features. . . . . . . . . . . . . . . . . . . . . . 12

CONTENTS
ii
English
About the Li-Ion Battery . . . . . . . . . . . . .12
Battery Recycling and Disposal . . . . . . .13
Removing the Lithium-Ion (Li-Ion)
Battery. . . . . . . . . . . . . . . . . . . . . . . . . . .14
Power Supply, Adapter and Drop-in Tray
Charger. . . . . . . . . . . . . . . . . . . . . . . . . .14
Charging a Standalone Battery. . . . . . . .15
Charging the Bluetooth Headset. . . . . . .18
Checking Battery Status . . . . . . . . . . . . .18
Batteries and Chargers Safety
Information. . . . . . . . . . . . . . . . . . . . . . . . . .19
Operational Safety Guidelines . . . . . . . .20
Programming the Radio through
the CPS . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Downloading the (Customer
Programming Software) CPS . . . . . . . . .21
Radio Cloning . . . . . . . . . . . . . . . . . . . . . . .24
Cloning Radio Settings . . . . . . . . . . . . . . . . .24
Cloning Instructions. . . . . . . . . . . . . . . . . . . .24
Cloning Radios using the CLP Series
Cloning Cable Kit P/N HKKN4026 (optional
accessory) . . . . . . . . . . . . . . . . . . . . . . . 24
Cloning Radios using the CLP Series
Multi-Unit Charger (MUC) Kit P/N
HKPN4007 (optional accessory) . . . . . . 27
Advanced Radio Configuration (*) . . . . . . 28
Entering Advanced Radio
Configuration Mode . . . . . . . . . . . . . . . . 28
Troubleshooting. . . . . . . . . . . . . . . . . . . . . 29
Use and Care . . . . . . . . . . . . . . . . . . . . . . . 33
Radio Frequency and Code Charts . . . . . 34
Motorola Limited Warranty for the United
States and Canada . . . . . . . . . . . . . . . . . . . 37
Accessories . . . . . . . . . . . . . . . . . . . . . . . . 42
Audio Accessories . . . . . . . . . . . . . . . . . . . . 42
Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Carry Accessories . . . . . . . . . . . . . . . . . . . . 42
Chargers . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Programming Cables . . . . . . . . . . . . . . . . . . 43

COMPUTER SOFTWARE
COPYRIGHTS
English
iii
COMPUTER SOFTWARE
COPYRIGHTS
The Motorola products described in this
manual may include copyrighted Motorola
computer programs stored in semiconductor
memories or other media. Laws in the United
States and other countries preserve for
Motorola certain exclusive rights for
copyrighted computer programs, including, but
not limited to, the exclusive right to copy or
reproduce in any form the copyrighted
computer program. Accordingly, any
copyrighted Motorola computer programs
contained in the Motorola products described in
this manual may not be copied, reproduced,
modified, reverse-engineered, or distributed in
any manner without the express written
permission of Motorola.
Furthermore, the purchase of Motorola
products shall not be deemed to grant either
directly or by implication, estoppels, or
otherwise, any license under the copyrights,
patents or patent applications of Motorola,
except for the normal non-exclusive license to
use that arises by operation of law in the sale of
a product.

RF SAFETY STANDARDS
English iv
RADIO FREQUENCY (RF)
EXPOSURE SAFETY
STANDARDS
Product Safety and RF Exposure
Compliance
ATTENTION!
This radio is restricted to occupational use only to
satisfy FCC RF energy exposure requirements.
Before using this product, read the RF energy
awareness information and operating instructions in
the Product Safety and RF Exposure booklet
enclosed with your radio (Motorola Publication part
number 6881095C98) to ensure compliance with RF
energy exposure limits.
For a list of Motorola-approved antennas, batteries,
and other accessories, visit the following website:
www.motorolasolutions.com/CLP
Before using this product, read the
operating instructions for safe
usage contained in the Product
Safety and RF Exposure booklet
contained with your radio.
Caution

CANADA LICENSING
INFORMATION
English
v
CANADA LICENSING
INFORMATION
GENERAL INFORMATION
The operation of your Motorola radio is subject
to the Radiocommunications Act and must
comply with rules and regulations of the
Federal Government’s department of Industry
Canada. Industry Canada requires that all
operators using Private Land Mobile
frequencies obtain a radio license before
operating their equipment.
An application for your Industry Canada license
is made on the form included with your
packaged radio models. Additional forms and
latest license application versions can be
obtained from the nearest Industry Canada
District office. A list of these offices is included
for your information.
THE LICENSE APPLICATION
General Instructions
1. Fill in the items as per the instructions. If you
need additional space for any item use the
reverse side of the application.
2. Be sure to print legibly.
3. Make a copy for your files.
4. Prepare a cheque or money order made out to
the “Receiver General for Canada”, for an
amount, which is on the following schedule, for
each radio purchased. (License is renewed on
April 1st of each year, and issued for a period of
12 months).
5. Mail your completed application, along with your
cheque or money order to the closest Industry
Canada District office, according to the list on
pages.
To obtain the latest Canadian License
Application form, please go to:
http://www.ic.gc.ca/ic_wp-pa.htm

CANADA LICENSING
INFORMATION
English vi
Notes

INTRODUCTION
English
1
INTRODUCTION
Thank you for purchasing a Motorola CLP Series
Two-Way Radio™. Your radio is a product of
Motorola’s 80 plus years of experience as a world
leader in designing and manufacturing
communications equipment. The CLP Series radios
provide cost-effective efficient communications for
businesses such as retail stores, restaurants, hotels,
and schools. Motorola professional two-way radios
are the perfect communications solution for all of
today’s fast-paced industries. Please read this guide
carefully so you know how to properly operate the
radio before use.
PACKAGE CONTENTS
Your product package contains the following products
and manuals:
• CLP Series Two-way Radio™
• Swivel Belt Clip Holster
• Lithium Ion Battery and Battery Door
• Drop-In Tray Charger with Transformer
• Audio Accessory
• User Quick Reference, Chargers Instructions
Leaflet, RF Safety Booklet
• Warranty Card
For product information, visit us at:
www.motorolasolutions.com/CLP
For product-related questions, contact:
1-800-448-6686 in the USA
1-800-461-4575 in Canada
1-866-522-5210 on your TTY (Text Telephone)
This user guide covers the following CLP Series™ models (*):
Note: Certain models may or may not be available at the time of purchase.
Model Frequency
Band
Transmit
Power
No. of
Channels Bluetooth Repeater Capability
CLP1013 UHF 1W 1 No Yes
CLP1043 UHF 1W 4 No Yes
CLP1063 UHF 1W 6 Yes Yes

RADIO OVERVIEW
English 2
RADIO OVERVIEW
RADIO CONTROLS
A
ccessory
Connector
Smart Status
Glow
Volume
Control (+/-)
Power/Battery
Button
Push-to-Talk
(PTT) Button
Menu Button

English
3
RADIO OVERVIEW
GETTING STARTED
INSTALL THE BATTERY
1. Push up the latch at the bottom of the battery
door and lift the battery door off the radio.
2. Align the battery contacts with tabs in the
battery compartment. Insert the contact side of
the battery first, then press the battery down to
secure in place.
3. Put the battery door back on the radio. Push
down the latch to lock.
Note: The CLP Series radios’ standard packaged models come with standard Lithium Ion battery and the standard Lithium Ion
battery door. For option, customers can order Hi-capacity Lithium Ion battery (P/N HKNN4013) and the Hi-capacity Lithium
Ion battery door (P/N HKLN4440).

RADIO OVERVIEW
English 4
Connecting a Wired Audio Accessory
To connect the wired audio accessory:
1. Turn the radio OFF.
2. Remove the accessory connector cover
(applicable on bluetooth enabled models only).
3. Plug the audio accessory straight into the
accessory connector on the radio. Screw the
audio accessory plug into the connector until it
is tight and fully engaged with the connector.
4. Turn the radio ON. Press either the Battery
Status, Menu or Volume Control button to
check for audio through the audio accessory.
Note: The CLP Series radios offer a variety of audio
accessories. For detailed Audio Accessories List,
please refer to www.motorolasolutions.com/CLP
for information on approved accessories. Lower the
radio volume BEFORE placing the audio accessory
in or near your ear.

English
5
RADIO OVERVIEW
CONNECTING A BLUETOOTH WIRELESS
ACCESSORY (SELECT MODELS ONLY)
Adding Bluetooth Headset (Initial Pairing)
1. Turn the radio OFF.
2. Put Bluetooth headset in pairing mode. Refer to
your Bluetooth headset instructions leaflet.
3. Press and hold the PTT button and power
button simultaneously until radio shows the blue
LED.
Note: The Bluetooth feature is disabled when the wired
audio accessory is plugged into the accessory
connector on the CLP radio.
Reconnecting to Last Connected Bluetooth
Headset
1. Turn the radio OFF.
2. Press the power button to turn the radio ON.
(Make sure the Bluetooth headset is turned
ON).
Erasing Bluetooth Headset History and Add
Bluetooth Headset
1. Turn the radio OFF.
2. Put the Bluetooth headset in pairing mode.
Refer to your Bluetooth headset instructions
leaflet.
3. Press and hold the Menu button and power
button simultaneously until radio shows the blue
LED.
Note: (*) The CLP radio uses proximity pairing. Make sure
the headset is close enough to the CLP radio.
Pairing process takes about 14 seconds.
LED Configuration
User Mode LED Status Color
Bluetooth
Pairing Mode
• Last connection
– Fast blinking
blue
• Add or erase/
add – Solid blue
Pairing
Successfully
Blue/purple blinks for
5 seconds
Bluetooth
Disconnected
Red/purple blinks
until the radio
reconnects
Pairing Fail/
Timeout
Red/purple blinks
until radio reconnects

RADIO OVERVIEW
English 6
Turning the Radio On and Off
• To turn the radio ON, press and hold the Power/
Battery button until you hear a short tone and the
Smart Status Glow lights up.
• To turn it OFF, press and hold the button until you
hear a short tone and the Smart Status Glow
(red) indicator blinks once.
Adjusting the Volume
Turn the radio ON and set volume level by
pressing volume control (+/- button). A total of 16
volume levels are available.
Installing and Removing the Swivel Belt
Clip Holster
1. Slide the bottom of the radio into the holster.
2. Snap the top of the holster into the radio around
the accessory connector.
3. To remove the holster, pull either the top or
bottom tab(s) and pull the radio from the holster.
Note: When using a corded audio accessory, loop the
cord into the recess in the rear of the holster for
optimal plug retention.
4. Make a small loop in the cord. Pass the cord
through the cord guide, nest the cord in the
U-shaped groove. Pull tight to lock the cord in
place.
5. Turn the belt clip to the position as needed.
Note: The CLP Series radios offer a variety of flexible
carrying accessories. For detailed Carrying
Accessories List, please refer to
www.motorolasolutions.com/CLP for information
on approved accessories.
Cord
Guide
U-Shaped
Groove

English
7
RADIO OVERVIEW
TRANSMITTING AND RECEIVING
1. To talk, press and hold the PTT button on the
front of the radio (or on select wired audio
accessories with an inline PTT). Speak clearly
into the microphone on the audio accessory.
When finished talking, release the PTT to listen.
2. To receive, listen through the earpiece at the
volume level you have set. Press the PTT to
respond.
Note: The CLP Series radios always require the
use of an audio accessory with microphone
and speaker.
Talk Range
Industrial Multi-Level
Application
Inside steel/
concrete
industrial
buildings
Inside Multi-
Level
Buildings
Unit to Unit Up to 100,000
square feet
Up to 10 floors
With
Repeater
Up to 250,000
square feet
Up to 20 floors

RADIO OVERVIEW
English 8
OPERATION WITH MENU SETTINGS
Press Menu button to navigate through the Menu settings. Voice Assisted Operation feature may
not be available on certain previous shipping models. At any time in Menu mode, short press PTT or
wait 3 seconds to exit the menu.
HOW TO... STEP 1 STEP 2
Change Channel Press Menu button to navigate to
Channel.
Press +/- button to change
channel.
Enter Monitor Mode Press Menu button to navigate to
Monitor.
Press +/- button to activate
or deactivate Monitor.
Enter Scan Mode Press Menu button to navigate to
Scan.
Press +/- button to activate
or deactivate Scan.
Send Call Tone (enabled
through CPS)
Press Menu button to navigate to
Call Tone.
Press +/- button to send
Call Tone.
Quick Tip: It is not necessary to wait for the voice prompt to be completed before continuing with next button
press.
Note: For single channel models, Monitor, Scan Mode and Call Tone are supported. Single channel models
support Scan Mode when the user enables “Dynamic Talkaround Scan” on a repeater channel via the
customer programming software.

English
9
RADIO OVERVIEW
Selecting a Channel
For CLP multi-channel models only:
• When powered ON, press the Menu button, you
will hear the voice prompt:
• [Color] “Channel” – [Channel#] – “To change” –
“press +/-”
• Select the channel you want. The LED will reflect
the color of the new channel. Press PTT button to
confirm or it is activated after a 3 second hang
time.
CLP1013 Single-Channel Models CLP1043 Multi-Channel Models CLP1063 Multi-
Channel Models
Channel LED Status Color Channel
LED
Status
Color Channel
LED
Status
Color
1 Red
1
Red 1 Red
2 Green 2Green
3Yellow 3Yellow
4 Blue 4 Blue
5 Purple
6White

RADIO OVERVIEW
English 10
Monitoring a Channel
1. To activate, press the Menu button to navigate
to Monitor mode.
2. When Monitor is OFF, you will hear the voice
prompt: “Monitor” – “To activate” – “press +/-”.
3. Press either “+/-“ button to activate the Monitor;
press either “+/-“ button again to deactivate.
Note: When Monitor is ON, you will hear static if
no activity is present or audio if channel
activity is present.
4. To engage the Monitor mode, enable Monitor via
the menu and let the menu time out.
5. To deactivate, press PTT during Monitor Menu
mode.
Scanning
(*) For multi-channel models only
You can scan up to 4 channels on CLP 1043
models and scan up to 6 channels on CLP1063
models. When the radio detects activity, it stops
scanning and locks in on the active channel.
This allows you to talk and listen to the person
transmitting without changing channels.
1. Press the Menu button to navigate to Scan
mode.
2. When Scan is OFF, you will hear the voice
prompt: “Scan” – “To activate” – “press +/-”.
3. Press either “+/-“ button to activate the Scan;
press either “+/-“ button again to deactivate.
4. When Scan is on, you will hear the voice
prompt: “Scan” – “To deactivate” – “press +/-”
button.

English
11
RADIO OVERVIEW
Dynamic Talkaround Scan (*)
"Dynamic Talkaround Scan" is a simple but
effective method for an on-site repeater enabled
two-way radio systems to maximize
communication coverage. This feature can be
enabled on a repeater channel via the Customer
Programming Software (CPS). The Dynamic
Talkaround Scan gives the radio the ability to scan
both the transmit and receive frequencies of a
repeater channel.
Note: (*) Enhancement feature on CLP Radios. May not
be available on previous shipping radios. The
Dynamic Talkaround Scan is given higher priority
then the Scan Mode. If the Dynamic Talkaround
Scan and Scan is enabled on the home channel,
then the radio can only support the Dynamic
Talkaround Scan.
Sending Call Tone (enabled through CPS)
1. Press the Menu button to navigate to Call Tone.
2. Press either “+/-“ button to transmit selected
Call Tone.
Note: There are 4 Call Tones available.
Mute Feature (*)
You can quickly lower the headset volume using
the Mute feature.
1. Press and hold + or - button while receiving
audio to quickly lower the headset volume to
“Mute Headset Volume” setting (configurable via
CPS). You can hear the voice prompt: "Mute"
2. To switch back to the previous headset volume
setting, press and hold + or - button again. You
can hear the voice prompt: "Unmute".
Note: (*) Enhancement feature on CLP radios. May not
available on previous shipping radios. The
enhanced CLP does not support the volume scroll
like the previous CLP models.
Talk Permit Tone (*)
In mixed fleet situations (CLP1013 or CLP1043 and
CLP1063), Bluetooth users may miss some words
due to the Bluetooth connection not being
established. Talk Permit Tone allocates some time so
that the link between the radio and headset gets
reestablished thus minimizing the lost words. (The
Talk Permit Tone is disabled by default on CPS on the
Bluetooth models).
Note: (*) Enhancement feature on CLP radios may not be
available on previous shipping radios.

BATTERY AND CHARGER
FEATURES
English 12
BATTERY AND CHARGER
FEATURES
BATTERY FEATURES
The CLP Series radio provides Lithium-Ion
batteries that come in different capacities that will
define the battery life.
About the Li-Ion Battery
The CLP Series radio comes equipped with a
rechargeable Li-Ion battery. This battery should be
charged before initial use to ensure optimum
capacity and performance.
Battery life is determined by several factors.
Among the more critical are the regular
overcharge of batteries and the average depth of
discharge with each cycle. Typically, the greater
the overcharge and the deeper the average
discharge, the fewer cycles a battery will last. For
example, a battery which is overcharged and
discharged 100% several times a day, lasts fewer
cycles than a battery that receives less of an
overcharge and is discharged to 50% per day.
Further, a battery which receives minimal
overcharging and averages only 25% discharge,
lasts even longer.
Motorola batteries are designed specifically to be
used with a Motorola charger and vice versa.
Charging in non-Motorola equipment may lead to
battery damage and void the battery warranty. The
battery should be at about 77 °F (25 °C) (room
temperature), whenever possible. Charging a cold
battery (below 50 ° F [10 °C]) may result in
leakage of electrolyte and ultimately in failure of
the battery. Charging a hot battery (above 95 °F
[35 °C]) results in reduced discharge capacity,
affecting the performance of the radio. Motorola
rapid-rate battery chargers contain a temperature-
sensing circuit to ensure that batteries are
charged within the temperature limits stated
above.
Battery Life
Based on 5% transmit, 5% receive, 90% standby
(standard duty cycle):
Estimated Battery Life
Charging
Solution
Battery Type
Standard Li- Ion
Battery
High Capacity
Li-Ion Battery
CLP1013,
CLP1043 9 hours 14 hours
CLP1063 8 hours 12 hours