Motorola MTP8500 Ex User manual

www.motorolasolutions.com www.motorolasolutions.com
14
1
2
20
3
4
5
15
7
21
22
13
17
18
11
12
4
8
9
16
19
6
7
23
24
10
12
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
MTP8500 Ex
QUICK START GUIDE
Controls and Indicators
Getting Started
Installing the Battery
Attaching the Antenna
Unlocking the Radio
Battery installing must occur only in non-hazardous areas.
Remove the battery from its protective case.
Fit the customizable label (1). Insert the battery into the compartment (2).
Carefully slide the battery towards the top of the radio until it clicks into place.
Turn the radio off before attaching the antenna.
Align the bottom of the antenna and the screw-in base on the top of the
radio.
Turn clockwise until snug. Do not force.
Your radio may be locked at power up. To unlock the radio after powering
on, enter the code at the prompt using Navigation keys.
The unlock code is originally set to 0000. Your service provider may change
this number before you receive your radio.
Signal Indicator Status
Indicator
Solid green
Blinking green
Solid red
Blinking red
Solid orange
Blinking orange
No indication
Battery Capacity Information
Information Description
Full (80% – 100% capacity)
Middle (60% – 80% capacity)
Low (25% – 60% capacity)
Very low (5% – 25% capacity)
Less than 5% capacity
Unlocking/Locking the Keypad
To unlock/lock the keypad, press the Menu key and then Left Navigation key.
Status
In use
In service
Out of service
Connecting to a network
Entering DMO
Transmit Inhibit in service
Channel busy in DMO
Incoming private or phone call
Switched off or in Covert Mode
Charging
Status
Fully Charged
Rapid Charge
Faulty or Invalid
Battery
Battery is waiting
to charge
90% - 99% Charged
Holding Your Radio
The radio has two microphones:
• A top microphone for simplex group, dispatcher, or private calls
• A bottom microphone for duplex, telephone-like calls
When making duplex calls (low audio), hold your
radio as you would a telephone. Speak into the
bottom microphone. Listen via the earpiece. Keep
the antenna at least 2.5 cm from your head and
body.
When making simplex calls (high audio), hold the
radio in a vertical position with the top microphone
5 to 10 cm away from your mouth. Speak into the
top microphone. Listen via the radio internal
speaker. Keep the antenna at least 2.5 cm from
your head and body.
Looking After Your Radio
Never leave your radio or battery in extreme temperatures
(over +85 °C), for example, behind a windscreen in direct sunlight.
The radio is submersible (compliant with the IP67 standard) - but only with the
battery, antenna, and dust cover or its equivalent, attached.
To clean your radio, use a moistened or antistatic cloth.
If the radio is exposed to impure liquids such as dirty water or salt water, follow
the washing procedures as described in the Appendix section of the MTP8500Ex
Feature User Guide.
Speaker
Front Display
Top Display
Customizable Label Space
Send Key
Bottom Microphone
Programmable Function Key
Antenna
Emergency Button
Belt Clip Connector
Top Microphone
Signal Indicator
Side Connector
Soft Key
Charger Connector
Battery Latch
On-Off/End/Home Key
Menu Key
Four Way Navigation Key
Push-To-Talk Button (PTT)
Earpiece
Talkgroup/Volume Knob
Programmable Side Button
Programmable Function Key
-
-
MTP8500Ex_QuickStartGuide.ai 1 09-Apr-21 4:35:48 PMMTP8500Ex_QuickStartGuide.ai 1 09-Apr-21 4:35:48 PM

www.motorolasolutions.com www.motorolasolutions.com
14
1
2
20
3
4
5
15
7
21
22
13
17
18
11
12
4
8
9
16
19
6
7
23
24
10
12
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
MTP8500 Ex
QUICK START GUIDE
Controls and Indicators
Getting Started
Installing the Battery
Attaching the Antenna
Unlocking the Radio
Battery installing must occur only in non-hazardous areas.
Remove the battery from its protective case.
Fit the customizable label (1). Insert the battery into the compartment (2).
Carefully slide the battery towards the top of the radio until it clicks into place.
Turn the radio off before attaching the antenna.
Align the bottom of the antenna and the screw-in base on the top of the
radio.
Turn clockwise until snug. Do not force.
Your radio may be locked at power up. To unlock the radio after powering
on, enter the code at the prompt using Navigation keys.
The unlock code is originally set to 0000. Your service provider may change
this number before you receive your radio.
Signal Indicator Status
Indicator
Solid green
Blinking green
Solid red
Blinking red
Solid orange
Blinking orange
No indication
Battery Capacity Information
Information Description
Full (80% – 100% capacity)
Middle (60% – 80% capacity)
Low (25% – 60% capacity)
Very low (5% – 25% capacity)
Less than 5% capacity
Unlocking/Locking the Keypad
To unlock/lock the keypad, press the Menu key and then Left Navigation key.
Status
In use
In service
Out of service
Connecting to a network
Entering DMO
Transmit Inhibit in service
Channel busy in DMO
Incoming private or phone call
Switched off or in Covert Mode
Charging
Status
Fully Charged
Rapid Charge
Faulty or Invalid
Battery
Battery is waiting
to charge
90% - 99% Charged
Holding Your Radio
The radio has two microphones:
• A top microphone for simplex group, dispatcher, or private calls
• A bottom microphone for duplex, telephone-like calls
When making duplex calls (low audio), hold your
radio as you would a telephone. Speak into the
bottom microphone. Listen via the earpiece. Keep
the antenna at least 2.5 cm from your head and
body.
When making simplex calls (high audio), hold the
radio in a vertical position with the top microphone
5 to 10 cm away from your mouth. Speak into the
top microphone. Listen via the radio internal
speaker. Keep the antenna at least 2.5 cm from
your head and body.
Looking After Your Radio
Never leave your radio or battery in extreme temperatures
(over +85 °C), for example, behind a windscreen in direct sunlight.
The radio is submersible (compliant with the IP67 standard) - but only with the
battery, antenna, and dust cover or its equivalent, attached.
To clean your radio, use a moistened or antistatic cloth.
If the radio is exposed to impure liquids such as dirty water or salt water, follow
the washing procedures as described in the Appendix section of the MTP8500Ex
Feature User Guide.
Speaker
Front Display
Top Display
Customizable Label Space
Send Key
Bottom Microphone
Programmable Function Key
Antenna
Emergency Button
Belt Clip Connector
Top Microphone
Signal Indicator
Side Connector
Soft Key
Charger Connector
Battery Latch
On-Off/End/Home Key
Menu Key
Four Way Navigation Key
Push-To-Talk Button (PTT)
Earpiece
Talkgroup/Volume Knob
Programmable Side Button
Programmable Function Key
-
-
MTP8500Ex_QuickStartGuide.ai 1 09-Apr-21 4:35:48 PMMTP8500Ex_QuickStartGuide.ai 1 09-Apr-21 4:35:48 PM

www.motorolasolutions.com www.motorolasolutions.com
14
1
2
20
3
4
5
15
7
21
22
13
17
18
11
12
4
8
9
16
19
6
7
23
24
10
12
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
MTP8500 Ex
QUICK START GUIDE
Controls and Indicators
Getting Started
Installing the Battery
Attaching the Antenna
Unlocking the Radio
Battery installing must occur only in non-hazardous areas.
Remove the battery from its protective case.
Fit the customizable label (1). Insert the battery into the compartment (2).
Carefully slide the battery towards the top of the radio until it clicks into place.
Turn the radio off before attaching the antenna.
Align the bottom of the antenna and the screw-in base on the top of the
radio.
Turn clockwise until snug. Do not force.
Your radio may be locked at power up. To unlock the radio after powering
on, enter the code at the prompt using Navigation keys.
The unlock code is originally set to 0000. Your service provider may change
this number before you receive your radio.
Signal Indicator Status
Indicator
Solid green
Blinking green
Solid red
Blinking red
Solid orange
Blinking orange
No indication
Battery Capacity Information
Information Description
Full (80% – 100% capacity)
Middle (60% – 80% capacity)
Low (25% – 60% capacity)
Very low (5% – 25% capacity)
Less than 5% capacity
Unlocking/Locking the Keypad
To unlock/lock the keypad, press the Menu key and then Left Navigation key.
Status
In use
In service
Out of service
Connecting to a network
Entering DMO
Transmit Inhibit in service
Channel busy in DMO
Incoming private or phone call
Switched off or in Covert Mode
Charging
Status
Fully Charged
Rapid Charge
Faulty or Invalid
Battery
Battery is waiting
to charge
90% - 99% Charged
Holding Your Radio
The radio has two microphones:
• A top microphone for simplex group, dispatcher, or private calls
• A bottom microphone for duplex, telephone-like calls
When making duplex calls (low audio), hold your
radio as you would a telephone. Speak into the
bottom microphone. Listen via the earpiece. Keep
the antenna at least 2.5 cm from your head and
body.
When making simplex calls (high audio), hold the
radio in a vertical position with the top microphone
5 to 10 cm away from your mouth. Speak into the
top microphone. Listen via the radio internal
speaker. Keep the antenna at least 2.5 cm from
your head and body.
Looking After Your Radio
Never leave your radio or battery in extreme temperatures
(over +85 °C), for example, behind a windscreen in direct sunlight.
The radio is submersible (compliant with the IP67 standard) - but only with the
battery, antenna, and dust cover or its equivalent, attached.
To clean your radio, use a moistened or antistatic cloth.
If the radio is exposed to impure liquids such as dirty water or salt water, follow
the washing procedures as described in the Appendix section of the MTP8500Ex
Feature User Guide.
Speaker
Front Display
Top Display
Customizable Label Space
Send Key
Bottom Microphone
Programmable Function Key
Antenna
Emergency Button
Belt Clip Connector
Top Microphone
Signal Indicator
Side Connector
Soft Key
Charger Connector
Battery Latch
On-Off/End/Home Key
Menu Key
Four Way Navigation Key
Push-To-Talk Button (PTT)
Earpiece
Talkgroup/Volume Knob
Programmable Side Button
Programmable Function Key
-
-
MTP8500Ex_QuickStartGuide.ai 1 09-Apr-21 4:35:48 PMMTP8500Ex_QuickStartGuide.ai 1 09-Apr-21 4:35:48 PM

www.motorolasolutions.com www.motorolasolutions.com
14
1
2
20
3
4
5
15
7
21
22
13
17
18
11
12
4
8
9
16
19
6
7
23
24
10
12
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
MTP8500 Ex
QUICK START GUIDE
Controls and Indicators
Getting Started
Installing the Battery
Attaching the Antenna
Unlocking the Radio
Battery installing must occur only in non-hazardous areas.
Remove the battery from its protective case.
Fit the customizable label (1). Insert the battery into the compartment (2).
Carefully slide the battery towards the top of the radio until it clicks into place.
Turn the radio off before attaching the antenna.
Align the bottom of the antenna and the screw-in base on the top of the
radio.
Turn clockwise until snug. Do not force.
Your radio may be locked at power up. To unlock the radio after powering
on, enter the code at the prompt using Navigation keys.
The unlock code is originally set to 0000. Your service provider may change
this number before you receive your radio.
Signal Indicator Status
Indicator
Solid green
Blinking green
Solid red
Blinking red
Solid orange
Blinking orange
No indication
Battery Capacity Information
Information Description
Full (80% – 100% capacity)
Middle (60% – 80% capacity)
Low (25% – 60% capacity)
Very low (5% – 25% capacity)
Less than 5% capacity
Unlocking/Locking the Keypad
To unlock/lock the keypad, press the Menu key and then Left Navigation key.
Status
In use
In service
Out of service
Connecting to a network
Entering DMO
Transmit Inhibit in service
Channel busy in DMO
Incoming private or phone call
Switched off or in Covert Mode
Charging
Status
Fully Charged
Rapid Charge
Faulty or Invalid
Battery
Battery is waiting
to charge
90% - 99% Charged
Holding Your Radio
The radio has two microphones:
• A top microphone for simplex group, dispatcher, or private calls
• A bottom microphone for duplex, telephone-like calls
When making duplex calls (low audio), hold your
radio as you would a telephone. Speak into the
bottom microphone. Listen via the earpiece. Keep
the antenna at least 2.5 cm from your head and
body.
When making simplex calls (high audio), hold the
radio in a vertical position with the top microphone
5 to 10 cm away from your mouth. Speak into the
top microphone. Listen via the radio internal
speaker. Keep the antenna at least 2.5 cm from
your head and body.
Looking After Your Radio
Never leave your radio or battery in extreme temperatures
(over +85 °C), for example, behind a windscreen in direct sunlight.
The radio is submersible (compliant with the IP67 standard) - but only with the
battery, antenna, and dust cover or its equivalent, attached.
To clean your radio, use a moistened or antistatic cloth.
If the radio is exposed to impure liquids such as dirty water or salt water, follow
the washing procedures as described in the Appendix section of the MTP8500Ex
Feature User Guide.
Speaker
Front Display
Top Display
Customizable Label Space
Send Key
Bottom Microphone
Programmable Function Key
Antenna
Emergency Button
Belt Clip Connector
Top Microphone
Signal Indicator
Side Connector
Soft Key
Charger Connector
Battery Latch
On-Off/End/Home Key
Menu Key
Four Way Navigation Key
Push-To-Talk Button (PTT)
Earpiece
Talkgroup/Volume Knob
Programmable Side Button
Programmable Function Key
-
-
MTP8500Ex_QuickStartGuide.ai 1 09-Apr-21 4:35:48 PMMTP8500Ex_QuickStartGuide.ai 1 09-Apr-21 4:35:48 PM

www.motorolasolutions.com www.motorolasolutions.com
14
1
2
20
3
4
5
15
7
21
22
13
17
18
11
12
4
8
9
16
19
6
7
23
24
10
12
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
MTP8500 Ex
QUICK START GUIDE
Controls and Indicators
Getting Started
Installing the Battery
Attaching the Antenna
Unlocking the Radio
Battery installing must occur only in non-hazardous areas.
Remove the battery from its protective case.
Fit the customizable label (1). Insert the battery into the compartment (2).
Carefully slide the battery towards the top of the radio until it clicks into place.
Turn the radio off before attaching the antenna.
Align the bottom of the antenna and the screw-in base on the top of the
radio.
Turn clockwise until snug. Do not force.
Your radio may be locked at power up. To unlock the radio after powering
on, enter the code at the prompt using Navigation keys.
The unlock code is originally set to 0000. Your service provider may change
this number before you receive your radio.
Signal Indicator Status
Indicator
Solid green
Blinking green
Solid red
Blinking red
Solid orange
Blinking orange
No indication
Battery Capacity Information
Information Description
Full (80% – 100% capacity)
Middle (60% – 80% capacity)
Low (25% – 60% capacity)
Very low (5% – 25% capacity)
Less than 5% capacity
Unlocking/Locking the Keypad
To unlock/lock the keypad, press the Menu key and then Left Navigation key.
Status
In use
In service
Out of service
Connecting to a network
Entering DMO
Transmit Inhibit in service
Channel busy in DMO
Incoming private or phone call
Switched off or in Covert Mode
Charging
Status
Fully Charged
Rapid Charge
Faulty or Invalid
Battery
Battery is waiting
to charge
90% - 99% Charged
Holding Your Radio
The radio has two microphones:
• A top microphone for simplex group, dispatcher, or private calls
• A bottom microphone for duplex, telephone-like calls
When making duplex calls (low audio), hold your
radio as you would a telephone. Speak into the
bottom microphone. Listen via the earpiece. Keep
the antenna at least 2.5 cm from your head and
body.
When making simplex calls (high audio), hold the
radio in a vertical position with the top microphone
5 to 10 cm away from your mouth. Speak into the
top microphone. Listen via the radio internal
speaker. Keep the antenna at least 2.5 cm from
your head and body.
Looking After Your Radio
Never leave your radio or battery in extreme temperatures
(over +85 °C), for example, behind a windscreen in direct sunlight.
The radio is submersible (compliant with the IP67 standard) - but only with the
battery, antenna, and dust cover or its equivalent, attached.
To clean your radio, use a moistened or antistatic cloth.
If the radio is exposed to impure liquids such as dirty water or salt water, follow
the washing procedures as described in the Appendix section of the MTP8500Ex
Feature User Guide.
Speaker
Front Display
Top Display
Customizable Label Space
Send Key
Bottom Microphone
Programmable Function Key
Antenna
Emergency Button
Belt Clip Connector
Top Microphone
Signal Indicator
Side Connector
Soft Key
Charger Connector
Battery Latch
On-Off/End/Home Key
Menu Key
Four Way Navigation Key
Push-To-Talk Button (PTT)
Earpiece
Talkgroup/Volume Knob
Programmable Side Button
Programmable Function Key
-
-
MTP8500Ex_QuickStartGuide.ai 1 09-Apr-21 4:35:48 PMMTP8500Ex_QuickStartGuide.ai 1 09-Apr-21 4:35:48 PM

www.motorolasolutions.com www.motorolasolutions.com
m
MTP8500 Ex
QUICK START GUIDE
Icons
Using the Terminal
More Information on the Radio
Learning Experience Portal
*MN002024A01*
MN002024A01-BC
This document is copyright protected. Duplications for the purpose of the use of Motorola Solutions products
are permitted to an appropriate extent. Duplications for other purposes, changes, additions or other
processing of this document are not permitted. Only this electronically-saved document is considered to be
the original. Duplications are considered merely copies. Motorola Solutions, Inc., and its subsidiaries and
affiliates do not vouch for the correctness of such kinds of copies.
MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks or registered trademarks of
Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective
owners.
© 2015 and 2021 Motorola Solutions, Inc. All rights reserved.
User documentation available at:
https://learning.motorolasolutions.com/
Open Source Software Legal Notices
Available in Customer Programming Software Plus (CPS Plus) DVD.
Visit the Motorola Solutions Web site at:
http://www.motorolasolutions.com/
Icon Description
New Message Has Arrived
New Message(s)
Packet Data Enabled
Packet Data Transmitting
Selected Icons
High RF Power
Icon Description
In Service (TMO)
No Service (TMO)
Signal Strength
Direct Mode (DMO)
Emergency Mode
Battery Level (Front/Top Display)
Battery Charging (Front/Top Display)
Duplex Ring Muted
Simplex Ring Muted
All Ring Muted
Low Audio
Migration
High Audio
Scan (TMO)
Priority Scan (TMO)
Earpiece Connected
Radio Keys Locked
Location
IN DMO: From the home screen, dial a number using Software Numeric Keypad (a
shortcut needs to be assigned to a Function Key or a Navigation Key - refer to the
Feature User Guide for details). Press and hold PTT to make the call and talk (wait for
the talk permit tone if configured). Release PTT to listen. Press the End key to
terminate the call.
IN TMO: From the home screen, dial a number using Software Numeric Keypad (a
shortcut needs to be assigned to a Function Key or a Navigation Key - refer to the
Feature User Guide for details). Press and release PTT to make the call. Wait for the
called party to pick up. Once the call is connected, press and hold PTT to talk (wait for
the talk permit tone if configured). Release PTT to listen. Press the End key to
terminate the call.
Making Duplex Private/Phone/PABX Calls
Turning the Radio On/Off
To power the radio on/off, press and hold On/Off key.
Using the Radio Menu
To enter the menu, press the Menu key.
To scroll through the menu, press the Up or Down Navigation key.
To select a menu item, press Select or the Right Navigation key.
To return to the previous level, press Back or the Left Navigation key.
To exit the menu, press the Home key.
Selecting Trunked/Direct Mode Operation
From the home screen, press Optns, then select Trunked Mode or Direct Mode.
Making Simplex Private Calls
Making TMO/DMO Group Calls
Enter TMO or DMO. From the home screen, use the Talkgroup Knob or Navigation
keys to highlight the target talkgroup. Press Select (if configured). Press and hold
PTT. Wait for the talk permit tone (if configured) and talk. Release PTT to listen.
Making TMO/DMO Emergency Group Calls
Sending Status Messages
Select the target talkgroup, then press the Menu key and select Messages >Send
Status. Highlight a status message and press the Send key or PTT to send it.
Sending SDS Messages
From the home screen, press the Menu key. Select Messages >New Message.
Enter your message and select Send. Select Private or Group. Enter a Private ID
or choose a group.
Enter TMO or DMO. Press and hold the Emergency button. The emergency alarm
is sent automatically (if configured). Press and hold PTT. Wait for the talk permit
tone (if configured) and talk. Release PTT to listen.
If using the Hot Mic feature, wait for the “Emgcy Mic On” message to appear on the
display, then talk without pressing PTT.
To exit the emergency mode, press and hold the Exit soft key.
From the home screen, dial a number using Software Numeric Keypad (a shortcut
needs to be assigned to a Function Key or a Navigation Key - refer to the Feature User
Guide for details). Change the call type by pressing Ctype. Press and release the Send
key. The ringing sounds. The called party answers. Press the End key to terminate the
call.
To answer an incoming call, press the Send key.
Pairing Your Radio with Bluetooth Devices
From the home screen, press the Menu key and select Bluetooth >Add Device.
Highlight the required device and select Pair. If needed, enter a PIN code or a passkey.
Using the Top Display
The radio is equipped with a secondary display placed at the top.
Use it to check for key information, such as the battery level, volume
level, signal strength, talkgroup name, or radio status.
Bluetooth No/Active Connection
MTP8500Ex_QuickStartGuide.ai 2 09-Apr-21 4:36:06 PMMTP8500Ex_QuickStartGuide.ai 2 09-Apr-21 4:36:06 PM

www.motorolasolutions.com www.motorolasolutions.com
m
MTP8500 Ex
QUICK START GUIDE
Icons
Using the Terminal
More Information on the Radio
Learning Experience Portal
*MN002024A01*
MN002024A01-BC
This document is copyright protected. Duplications for the purpose of the use of Motorola Solutions products
are permitted to an appropriate extent. Duplications for other purposes, changes, additions or other
processing of this document are not permitted. Only this electronically-saved document is considered to be
the original. Duplications are considered merely copies. Motorola Solutions, Inc., and its subsidiaries and
affiliates do not vouch for the correctness of such kinds of copies.
MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks or registered trademarks of
Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective
owners.
© 2015 and 2021 Motorola Solutions, Inc. All rights reserved.
User documentation available at:
https://learning.motorolasolutions.com/
Open Source Software Legal Notices
Available in Customer Programming Software Plus (CPS Plus) DVD.
Visit the Motorola Solutions Web site at:
http://www.motorolasolutions.com/
Icon Description
New Message Has Arrived
New Message(s)
Packet Data Enabled
Packet Data Transmitting
Selected Icons
High RF Power
Icon Description
In Service (TMO)
No Service (TMO)
Signal Strength
Direct Mode (DMO)
Emergency Mode
Battery Level (Front/Top Display)
Battery Charging (Front/Top Display)
Duplex Ring Muted
Simplex Ring Muted
All Ring Muted
Low Audio
Migration
High Audio
Scan (TMO)
Priority Scan (TMO)
Earpiece Connected
Radio Keys Locked
Location
IN DMO: From the home screen, dial a number using Software Numeric Keypad (a
shortcut needs to be assigned to a Function Key or a Navigation Key - refer to the
Feature User Guide for details). Press and hold PTT to make the call and talk (wait for
the talk permit tone if configured). Release PTT to listen. Press the End key to
terminate the call.
IN TMO: From the home screen, dial a number using Software Numeric Keypad (a
shortcut needs to be assigned to a Function Key or a Navigation Key - refer to the
Feature User Guide for details). Press and release PTT to make the call. Wait for the
called party to pick up. Once the call is connected, press and hold PTT to talk (wait for
the talk permit tone if configured). Release PTT to listen. Press the End key to
terminate the call.
Making Duplex Private/Phone/PABX Calls
Turning the Radio On/Off
To power the radio on/off, press and hold On/Off key.
Using the Radio Menu
To enter the menu, press the Menu key.
To scroll through the menu, press the Up or Down Navigation key.
To select a menu item, press Select or the Right Navigation key.
To return to the previous level, press Back or the Left Navigation key.
To exit the menu, press the Home key.
Selecting Trunked/Direct Mode Operation
From the home screen, press Optns, then select Trunked Mode or Direct Mode.
Making Simplex Private Calls
Making TMO/DMO Group Calls
Enter TMO or DMO. From the home screen, use the Talkgroup Knob or Navigation
keys to highlight the target talkgroup. Press Select (if configured). Press and hold
PTT. Wait for the talk permit tone (if configured) and talk. Release PTT to listen.
Making TMO/DMO Emergency Group Calls
Sending Status Messages
Select the target talkgroup, then press the Menu key and select Messages >Send
Status. Highlight a status message and press the Send key or PTT to send it.
Sending SDS Messages
From the home screen, press the Menu key. Select Messages >New Message.
Enter your message and select Send. Select Private or Group. Enter a Private ID
or choose a group.
Enter TMO or DMO. Press and hold the Emergency button. The emergency alarm
is sent automatically (if configured). Press and hold PTT. Wait for the talk permit
tone (if configured) and talk. Release PTT to listen.
If using the Hot Mic feature, wait for the “Emgcy Mic On” message to appear on the
display, then talk without pressing PTT.
To exit the emergency mode, press and hold the Exit soft key.
From the home screen, dial a number using Software Numeric Keypad (a shortcut
needs to be assigned to a Function Key or a Navigation Key - refer to the Feature User
Guide for details). Change the call type by pressing Ctype. Press and release the Send
key. The ringing sounds. The called party answers. Press the End key to terminate the
call.
To answer an incoming call, press the Send key.
Pairing Your Radio with Bluetooth Devices
From the home screen, press the Menu key and select Bluetooth >Add Device.
Highlight the required device and select Pair. If needed, enter a PIN code or a passkey.
Using the Top Display
The radio is equipped with a secondary display placed at the top.
Use it to check for key information, such as the battery level, volume
level, signal strength, talkgroup name, or radio status.
Bluetooth No/Active Connection
MTP8500Ex_QuickStartGuide.ai 2 09-Apr-21 4:36:06 PMMTP8500Ex_QuickStartGuide.ai 2 09-Apr-21 4:36:06 PM

www.motorolasolutions.com www.motorolasolutions.com
m
MTP8500 Ex
QUICK START GUIDE
Icons
Using the Terminal
More Information on the Radio
Learning Experience Portal
*MN002024A01*
MN002024A01-BC
This document is copyright protected. Duplications for the purpose of the use of Motorola Solutions products
are permitted to an appropriate extent. Duplications for other purposes, changes, additions or other
processing of this document are not permitted. Only this electronically-saved document is considered to be
the original. Duplications are considered merely copies. Motorola Solutions, Inc., and its subsidiaries and
affiliates do not vouch for the correctness of such kinds of copies.
MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks or registered trademarks of
Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective
owners.
© 2015 and 2021 Motorola Solutions, Inc. All rights reserved.
User documentation available at:
https://learning.motorolasolutions.com/
Open Source Software Legal Notices
Available in Customer Programming Software Plus (CPS Plus) DVD.
Visit the Motorola Solutions Web site at:
http://www.motorolasolutions.com/
Icon Description
New Message Has Arrived
New Message(s)
Packet Data Enabled
Packet Data Transmitting
Selected Icons
High RF Power
Icon Description
In Service (TMO)
No Service (TMO)
Signal Strength
Direct Mode (DMO)
Emergency Mode
Battery Level (Front/Top Display)
Battery Charging (Front/Top Display)
Duplex Ring Muted
Simplex Ring Muted
All Ring Muted
Low Audio
Migration
High Audio
Scan (TMO)
Priority Scan (TMO)
Earpiece Connected
Radio Keys Locked
Location
IN DMO: From the home screen, dial a number using Software Numeric Keypad (a
shortcut needs to be assigned to a Function Key or a Navigation Key - refer to the
Feature User Guide for details). Press and hold PTT to make the call and talk (wait for
the talk permit tone if configured). Release PTT to listen. Press the End key to
terminate the call.
IN TMO: From the home screen, dial a number using Software Numeric Keypad (a
shortcut needs to be assigned to a Function Key or a Navigation Key - refer to the
Feature User Guide for details). Press and release PTT to make the call. Wait for the
called party to pick up. Once the call is connected, press and hold PTT to talk (wait for
the talk permit tone if configured). Release PTT to listen. Press the End key to
terminate the call.
Making Duplex Private/Phone/PABX Calls
Turning the Radio On/Off
To power the radio on/off, press and hold On/Off key.
Using the Radio Menu
To enter the menu, press the Menu key.
To scroll through the menu, press the Up or Down Navigation key.
To select a menu item, press Select or the Right Navigation key.
To return to the previous level, press Back or the Left Navigation key.
To exit the menu, press the Home key.
Selecting Trunked/Direct Mode Operation
From the home screen, press Optns, then select Trunked Mode or Direct Mode.
Making Simplex Private Calls
Making TMO/DMO Group Calls
Enter TMO or DMO. From the home screen, use the Talkgroup Knob or Navigation
keys to highlight the target talkgroup. Press Select (if configured). Press and hold
PTT. Wait for the talk permit tone (if configured) and talk. Release PTT to listen.
Making TMO/DMO Emergency Group Calls
Sending Status Messages
Select the target talkgroup, then press the Menu key and select Messages >Send
Status. Highlight a status message and press the Send key or PTT to send it.
Sending SDS Messages
From the home screen, press the Menu key. Select Messages >New Message.
Enter your message and select Send. Select Private or Group. Enter a Private ID
or choose a group.
Enter TMO or DMO. Press and hold the Emergency button. The emergency alarm
is sent automatically (if configured). Press and hold PTT. Wait for the talk permit
tone (if configured) and talk. Release PTT to listen.
If using the Hot Mic feature, wait for the “Emgcy Mic On” message to appear on the
display, then talk without pressing PTT.
To exit the emergency mode, press and hold the Exit soft key.
From the home screen, dial a number using Software Numeric Keypad (a shortcut
needs to be assigned to a Function Key or a Navigation Key - refer to the Feature User
Guide for details). Change the call type by pressing Ctype. Press and release the Send
key. The ringing sounds. The called party answers. Press the End key to terminate the
call.
To answer an incoming call, press the Send key.
Pairing Your Radio with Bluetooth Devices
From the home screen, press the Menu key and select Bluetooth >Add Device.
Highlight the required device and select Pair. If needed, enter a PIN code or a passkey.
Using the Top Display
The radio is equipped with a secondary display placed at the top.
Use it to check for key information, such as the battery level, volume
level, signal strength, talkgroup name, or radio status.
Bluetooth No/Active Connection
MTP8500Ex_QuickStartGuide.ai 2 09-Apr-21 4:36:06 PMMTP8500Ex_QuickStartGuide.ai 2 09-Apr-21 4:36:06 PM

www.motorolasolutions.com www.motorolasolutions.com
m
MTP8500 Ex
QUICK START GUIDE
Icons
Using the Terminal
More Information on the Radio
Learning Experience Portal
*MN002024A01*
MN002024A01-BC
This document is copyright protected. Duplications for the purpose of the use of Motorola Solutions products
are permitted to an appropriate extent. Duplications for other purposes, changes, additions or other
processing of this document are not permitted. Only this electronically-saved document is considered to be
the original. Duplications are considered merely copies. Motorola Solutions, Inc., and its subsidiaries and
affiliates do not vouch for the correctness of such kinds of copies.
MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks or registered trademarks of
Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective
owners.
© 2015 and 2021 Motorola Solutions, Inc. All rights reserved.
User documentation available at:
https://learning.motorolasolutions.com/
Open Source Software Legal Notices
Available in Customer Programming Software Plus (CPS Plus) DVD.
Visit the Motorola Solutions Web site at:
http://www.motorolasolutions.com/
Icon Description
New Message Has Arrived
New Message(s)
Packet Data Enabled
Packet Data Transmitting
Selected Icons
High RF Power
Icon Description
In Service (TMO)
No Service (TMO)
Signal Strength
Direct Mode (DMO)
Emergency Mode
Battery Level (Front/Top Display)
Battery Charging (Front/Top Display)
Duplex Ring Muted
Simplex Ring Muted
All Ring Muted
Low Audio
Migration
High Audio
Scan (TMO)
Priority Scan (TMO)
Earpiece Connected
Radio Keys Locked
Location
IN DMO: From the home screen, dial a number using Software Numeric Keypad (a
shortcut needs to be assigned to a Function Key or a Navigation Key - refer to the
Feature User Guide for details). Press and hold PTT to make the call and talk (wait for
the talk permit tone if configured). Release PTT to listen. Press the End key to
terminate the call.
IN TMO: From the home screen, dial a number using Software Numeric Keypad (a
shortcut needs to be assigned to a Function Key or a Navigation Key - refer to the
Feature User Guide for details). Press and release PTT to make the call. Wait for the
called party to pick up. Once the call is connected, press and hold PTT to talk (wait for
the talk permit tone if configured). Release PTT to listen. Press the End key to
terminate the call.
Making Duplex Private/Phone/PABX Calls
Turning the Radio On/Off
To power the radio on/off, press and hold On/Off key.
Using the Radio Menu
To enter the menu, press the Menu key.
To scroll through the menu, press the Up or Down Navigation key.
To select a menu item, press Select or the Right Navigation key.
To return to the previous level, press Back or the Left Navigation key.
To exit the menu, press the Home key.
Selecting Trunked/Direct Mode Operation
From the home screen, press Optns, then select Trunked Mode or Direct Mode.
Making Simplex Private Calls
Making TMO/DMO Group Calls
Enter TMO or DMO. From the home screen, use the Talkgroup Knob or Navigation
keys to highlight the target talkgroup. Press Select (if configured). Press and hold
PTT. Wait for the talk permit tone (if configured) and talk. Release PTT to listen.
Making TMO/DMO Emergency Group Calls
Sending Status Messages
Select the target talkgroup, then press the Menu key and select Messages >Send
Status. Highlight a status message and press the Send key or PTT to send it.
Sending SDS Messages
From the home screen, press the Menu key. Select Messages >New Message.
Enter your message and select Send. Select Private or Group. Enter a Private ID
or choose a group.
Enter TMO or DMO. Press and hold the Emergency button. The emergency alarm
is sent automatically (if configured). Press and hold PTT. Wait for the talk permit
tone (if configured) and talk. Release PTT to listen.
If using the Hot Mic feature, wait for the “Emgcy Mic On” message to appear on the
display, then talk without pressing PTT.
To exit the emergency mode, press and hold the Exit soft key.
From the home screen, dial a number using Software Numeric Keypad (a shortcut
needs to be assigned to a Function Key or a Navigation Key - refer to the Feature User
Guide for details). Change the call type by pressing Ctype. Press and release the Send
key. The ringing sounds. The called party answers. Press the End key to terminate the
call.
To answer an incoming call, press the Send key.
Pairing Your Radio with Bluetooth Devices
From the home screen, press the Menu key and select Bluetooth >Add Device.
Highlight the required device and select Pair. If needed, enter a PIN code or a passkey.
Using the Top Display
The radio is equipped with a secondary display placed at the top.
Use it to check for key information, such as the battery level, volume
level, signal strength, talkgroup name, or radio status.
Bluetooth No/Active Connection
MTP8500Ex_QuickStartGuide.ai 2 09-Apr-21 4:36:06 PMMTP8500Ex_QuickStartGuide.ai 2 09-Apr-21 4:36:06 PM

www.motorolasolutions.com www.motorolasolutions.com
m
MTP8500 Ex
QUICK START GUIDE
Icons
Using the Terminal
More Information on the Radio
Learning Experience Portal
*MN002024A01*
MN002024A01-BC
This document is copyright protected. Duplications for the purpose of the use of Motorola Solutions products
are permitted to an appropriate extent. Duplications for other purposes, changes, additions or other
processing of this document are not permitted. Only this electronically-saved document is considered to be
the original. Duplications are considered merely copies. Motorola Solutions, Inc., and its subsidiaries and
affiliates do not vouch for the correctness of such kinds of copies.
MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks or registered trademarks of
Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective
owners.
© 2015 and 2021 Motorola Solutions, Inc. All rights reserved.
User documentation available at:
https://learning.motorolasolutions.com/
Open Source Software Legal Notices
Available in Customer Programming Software Plus (CPS Plus) DVD.
Visit the Motorola Solutions Web site at:
http://www.motorolasolutions.com/
Icon Description
New Message Has Arrived
New Message(s)
Packet Data Enabled
Packet Data Transmitting
Selected Icons
High RF Power
Icon Description
In Service (TMO)
No Service (TMO)
Signal Strength
Direct Mode (DMO)
Emergency Mode
Battery Level (Front/Top Display)
Battery Charging (Front/Top Display)
Duplex Ring Muted
Simplex Ring Muted
All Ring Muted
Low Audio
Migration
High Audio
Scan (TMO)
Priority Scan (TMO)
Earpiece Connected
Radio Keys Locked
Location
IN DMO: From the home screen, dial a number using Software Numeric Keypad (a
shortcut needs to be assigned to a Function Key or a Navigation Key - refer to the
Feature User Guide for details). Press and hold PTT to make the call and talk (wait for
the talk permit tone if configured). Release PTT to listen. Press the End key to
terminate the call.
IN TMO: From the home screen, dial a number using Software Numeric Keypad (a
shortcut needs to be assigned to a Function Key or a Navigation Key - refer to the
Feature User Guide for details). Press and release PTT to make the call. Wait for the
called party to pick up. Once the call is connected, press and hold PTT to talk (wait for
the talk permit tone if configured). Release PTT to listen. Press the End key to
terminate the call.
Making Duplex Private/Phone/PABX Calls
Turning the Radio On/Off
To power the radio on/off, press and hold On/Off key.
Using the Radio Menu
To enter the menu, press the Menu key.
To scroll through the menu, press the Up or Down Navigation key.
To select a menu item, press Select or the Right Navigation key.
To return to the previous level, press Back or the Left Navigation key.
To exit the menu, press the Home key.
Selecting Trunked/Direct Mode Operation
From the home screen, press Optns, then select Trunked Mode or Direct Mode.
Making Simplex Private Calls
Making TMO/DMO Group Calls
Enter TMO or DMO. From the home screen, use the Talkgroup Knob or Navigation
keys to highlight the target talkgroup. Press Select (if configured). Press and hold
PTT. Wait for the talk permit tone (if configured) and talk. Release PTT to listen.
Making TMO/DMO Emergency Group Calls
Sending Status Messages
Select the target talkgroup, then press the Menu key and select Messages >Send
Status. Highlight a status message and press the Send key or PTT to send it.
Sending SDS Messages
From the home screen, press the Menu key. Select Messages >New Message.
Enter your message and select Send. Select Private or Group. Enter a Private ID
or choose a group.
Enter TMO or DMO. Press and hold the Emergency button. The emergency alarm
is sent automatically (if configured). Press and hold PTT. Wait for the talk permit
tone (if configured) and talk. Release PTT to listen.
If using the Hot Mic feature, wait for the “Emgcy Mic On” message to appear on the
display, then talk without pressing PTT.
To exit the emergency mode, press and hold the Exit soft key.
From the home screen, dial a number using Software Numeric Keypad (a shortcut
needs to be assigned to a Function Key or a Navigation Key - refer to the Feature User
Guide for details). Change the call type by pressing Ctype. Press and release the Send
key. The ringing sounds. The called party answers. Press the End key to terminate the
call.
To answer an incoming call, press the Send key.
Pairing Your Radio with Bluetooth Devices
From the home screen, press the Menu key and select Bluetooth >Add Device.
Highlight the required device and select Pair. If needed, enter a PIN code or a passkey.
Using the Top Display
The radio is equipped with a secondary display placed at the top.
Use it to check for key information, such as the battery level, volume
level, signal strength, talkgroup name, or radio status.
Bluetooth No/Active Connection
MTP8500Ex_QuickStartGuide.ai 2 09-Apr-21 4:36:06 PMMTP8500Ex_QuickStartGuide.ai 2 09-Apr-21 4:36:06 PM