Motorola DLR1060 User manual

QUICK REFERENCE GUIDE
FOR RADIO FEATURES
DLR SERIES
DIGITAL
MADE EASY
MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license.
All other trademarks are the property of their respective owners. © 2015 Motorola Solutions, Inc. All rights reserved. Specifications are subject to change without notice. All specifications
shown are typical.
Click to begin

DLR SERIES
Quick Reference Guide
1. Radio Overview
2. Battery – Insert and Charge
3. Basic Operations
4. Advanced Configuration
5. Special Call Features
6. CPS Software
7. Troubleshooting and FAQ
Models:
DLR 1020 – 2 channels
DLR 1060 – 6 channels
Frequency band:
ISM 900 MHz
Table of Contents:

Audio
accessory
connector
Battery
DLR 1020/1060
Radio Overview
Antenna
Power
Button
Top Button
Volume/ Up-
Down Control
Buttons
Channel/Menu
Button
Tx/Rx
Indicator
LED
PTT
Button
Microphone
Speaker
Holster

DLR 1020/1060
Battery – Inserting
To insert or remove the battery, set the
latch in the “unlocked“ position, and open
the battery door.
Remember to always set the latch back to
the “locked” position in order to prevent
battery from falling out by accident.
Battery
door
Unlocked/Locked
latch

DLR 1020/1060
Battery – Charging
To charge a battery,
insert the radio or a
stand-alone battery into
the single or multiple unit
charger.
Multiple-unit
charger
Stand-alone
battery
Single-unit
charger
Note: Turn off the radio prior to charging. You don’t need to remove the holster to charge the radio.
Holster
LED turns green
– battery is fully
charged
The light on the charger
is red when the radio is
charging. It turns to green
once the radio is fully
charged.

DLR 1020/1060
Basic Operations ON/OFF
Power Button – long
press to turn the
device ON/OFF, short
press to check battery
status.
PRIVATE REPLY
Press Top Button to
queue up for Private
Reply* (while someone is
speaking to your channel),
then push PTT to call the
last person speaking.
VOLUME
[+] / [-] buttons –
press to adjust
volume
CHANNELS
Channel/Menu Button –
press to check the current
channel. You can now use
[+] and [-] buttons to
switch channels. Press
PTT to exit channel
browsing.
TALK
PTT (Push To Talk) Button
– push firmly, wait for the
TPT (Talk Permit Tone),
speak into the mic
(5 inches away from mouth)
Note: *Private Reply function is described here.

DLR 1020/1060
Advanced Configuration
The DLR Advanced Menu Mode allows you to configure special settings in your radio
without the need programming cables or additional software.
Choose a 4-digit number (0000 to 9999). Customize it to ensure
interference free/private communications.
Profile ID #
Choose the max. number of channels you want to allow for your
radio.
Max Channels
Set your Top button with one feature: Private Reply, Direct Call
(only if enabled via CPS), Call All Available, PageAllAvailable,
Mute, Disabled.
Top Button
Choose High, Medium or Low to adjust the radio microphone
sensitivity level to fit different users and/or noise environments.
MIC Gain
Choose the channel you want to designate as your main
channel: the radio will return to this channel in any case of
longer inactivity.
Home Channel

DLR 1020/1060
Advanced Configuration Menu
Entering Advanced Menu
PTT (Push-to-Talk)
Button
To enter the Advanced Menu, push
Power Button together with PTT
and [+]. Power
Button
[+] Button

DLR 1020/1060
Advanced Configuration Menu
Browsing Advanced Menu Options
Press Channel/Menu
button to cycle
through the Advanced
Menu options.
Profile
ID
Number
Max
Channel
Top
Button
MIC
Gain
Home
Channel
“Programming Mode.
Press Menu to
continue.”
Long press
PTT to exit
Advanced
Menu Mode.
Voice prompt

DLR 1020/1060
Advanced Configuration Menu
1. Profile ID Number – current value
Press
Channel/Menu
button to proceed to
nextAdvanced
Menu option.
Profile
ID
Number
Max
Channel
Top
Button
MIC
Gain
Home
Channel
“Current Profile ID:
<Digit1, Digit2, Digit3,
Digit4>; to change,
press [+] or [-]”
The radio announces the current PROFILE ID number
and prompts you to change it:
Press [+] or [-]
to enter the
Profile ID
number
Sub-Menu.
Long press
PTT to exit
Advanced
Menu Mode.
ATTENTION: Default Profile ID number is “0000”! Make sure to change it to avoid
interferences and ensure privacy.