MOVING INTELLIGENCE PHANTOM Vanguard Caravan Alarm User manual

COLLECTION
Caravan
Alarm
Protect your investment
Moving Intelligence (Phantom)
User Guide
Caravan
P
r
o
3
Pro
3
SENT
R
Y
Mi
0
1
SENTRY
SENTINEL
i
T
R
A
C
K

Manufactured exclusively for Phantom by
our partners at Gemini, the Vanguard alarm
is designed to secure your caravan simply
and reliably.
The standard alarm in corporates an electronic tilt sensor and
a wireless Passive Infrarred sensor PIR long with 2 four button
remotes.
The alarm does have the facility to turn the awning light on during
the arm and disarm process. This is likely only availible where your
alarm is factory tted.
The PIR can be excluded if necessary and the sensitivity of the tilt
sensor adjusted where required.
VANGUARD ALARM
2 3
Register online to validate your
warranty for your Vanguard alarm
www.movingintelligence.co.uk/vanguard
1System arming
The alarm unit can be armed by pressing the arm - button
1. Two high-pitched beeps will conrm the operation and
the dome light will turn ON for approx. 30 sec. The system
has a 30 sec. arming delay which allows you to exit the
caravan without triggering an alarm. After this delay, the
system is fully armed.
If the PIR sensor battery level is becoming exhausted, a
‘Bop’ will sound after the arming acoustic signals (replace
PIR internal batteries. Use only 2 CR2032 batteries.)
2System disarming
To disarm the system, press disarm - button 2 on the
remote control. Three high-pitched beeps will conrm
disarming and the dome light will turn ON for approx.
30 sec.
3System arming without
Internal sensors*
The system can be armed without enabling the wireless
PIR sensor(s). To do so, press button 3 on either remote
control to arm the system. One high-pitched beep will
conrm the system is armed with the sensors excluded.
Download our user guides in PDF
COLLECTION

VANGUARD ALARM
4 5
Register online to validate your
warranty for your Vanguard alarm
www.movingintelligence.co.uk/vanguard
4 Tilt sensor exclusion*
Arm the alarm as usual by pressing button 1. After the
usual two beeps wait 4 seconds and press button 3.
 Tiltsensorexclusionisconrmedbyonebeep.
5 Awning Light*
Arming/Disarming the alarm will activate the awning light for
30 seconds. Button 4 on the remote will also activate the light
for 5 minutes before automatically turning o.
*Typically awning light control will only be possible with factory installations.
DISARM
2
ARM
PET MODE/
NIGHT MODE
1
3
AWNING/
DOME
LIGHT
4
*Please note: Sensor exclusion is bound to a single arming cycle. Sensors
will automatically be enabled the next time the alarm is armed
6 Tilt sensor adjustment
The TILT sensor sensitivity level is factory set to trigger
an alarm if the vehicle is tilted at an angle of approx. 1.5°
with respect to the x, y and z-axis.Sensor sensitivity can
be custom-adjusted :
(every time you enter in ‘Adjustment Mode’, the sensitivity level will
automatically be restored to the 1.5° default setting).
Disarm the alarm system.
Simultaneously press, twice in a row, remote control buttons 1 and 2:
2 ‘Bops’ will conrm the system is in ‘Adjustment Mode’
Press button 2 once to increase the tilt angle to 3.5°:
operation will be conrmed by 1 beep.
Press button 2 again to increase the tilt angle to 7°:
operation will be conrmed by 1 beep.
Press button 2 once more to increase the tilt angle to 14°:
operation will be conrmed by 1 beep.
The system will automatically exit the adjustment mode after
this step. 1 ‘BOP’ will conrm the end of the procedure.
To exit the adjustment procedure and conrm the selected tilt
angle, simultaneously press remote control buttons 1 and 2
COLLECTION

VANGUARD ALARM
6 7
Register online to validate your
warranty for your Vanguard alarm
www.movingintelligence.co.uk/vanguard
7Alarms
An alarm event will trigger the siren for a maximum of 30
seconds. If the alarm condition remains or the alarm is not
disarmed it will trigger another cycle after a pause of 5
seconds. Each alarm condition will trigger a maximum of
8 cycles.
8Alarm trigger memory
If there has been an activation in your absence it will be
signaled by 2 long beeps on disarming, followed by a number
of high pitched ‘chirps’ to indicate the cause of the last
trigger. (See table)
9Pairing new devices
The alarm is supplied with 2 remotes and a wireless PIR
sensor but extra sensors can be added via the LEARN button.
Press the LEARN button 5 times in a row within 5 seconds.
Each press will generate a single beep and then a nal 2
beeps will conrm the system is in pairing mode for the next
30 seconds.
Press one of the new remote buttons or trigger the sensor to
be paired. A single beep will conrm the new device is added.
To exit pairing mode press the LEARN button once
1 Chirps
2 Chirps
3 Chirps
4 Chirps
: Wireless contacts Door opening
: Infared (PIR) Sensors
: External Input
: Tilt sensor
SIREN CHIRPS ALARM EVENTS
10 Battery replacement
When the remote batteries are too weak you’ll notice the
blue LED icker/ash when arming or disarming the alarm.
Replace the CR2032 battery
If the PIR battery is running low a secondary “bop” will
sound after the usual arming 2 beeps of the siren. To
replace the batteries detach the cover of the PIR from
its mounting base.
COLLECTION

Register online to validate your
warranty for your Vanguard alarm
www.movingintelligence.co.uk/vanguard
Motorhome
P
r
o
3
Pro
3
SENT
R
Y
Mi
0
1
SENTRY
SENTINEL
i
T
R
A
C
K
Other products available
www.movingintelligence.co.uk
UPGRADE
We oer upgrade deals if you have an
existing unit with us these can be aranged if
you contact us by phone or email. And are solely
for existing customers.
0161 219 4299
[e-mail]