Saferhomee HTZSAFE 806A User manual

Plug-in Alarm Receiver
User Manual

1
Plug-in Alarm Receiver
English Manual
Volume
Melody
Power Plug
2. System Components And Usage
1 piece
1 piece
Plug-in Alarm Receiver
Power Plug:plug the receiver into a socket
Zone Number
Volume: 4 adjustable volume levels
Melody: 35 optional melodies
Zone Number: flash for several seconds when the sensor
be activated
Note Please:
1. It is the extra wireless plug-in receiver
which is compatible with HTZSAFE wireless
alarm system; the receiver can not work alone,
it should work with HTZSAFE sensors.
2.If you want to add HTZSAFE sensors to the
receiver,set up them according to part 3 of the
manual or email us at
if you have any questions.
[e-mail]
1. Configuration List

3. Operation Instructions
(1)How to add sensors to the plug-in alarm receiver
(Total 4 zones and up to 4 sensors can be added to
the receiver)
Step 1
Plug the receiver into an outlet
Ring tone prompt and the zone number
will light up one by one for 3 times meaning
the receiver works properly.
Speaker
Speaker:sound for several seconds when
the sensor be activated
2

3
Step 3
the solar motion sensor)
Note: make the sensor close to the plug-in receiver
(within 30FT)
Activate the sensor.(for example:activate
(Zone number flashing
quickly and a ring tone
prompt meaning the
sensor has been added
to the plug-in receiver
properly)
flashing
quickly
Volume
All the Zone
numbers light up
press and hold the button
for 5 seconds
Volume
Zone 1 flashing
slowly
release the button
Volume
Step 2
Press and hold the “Volume” button for 5 seconds, release the
button when one of the zone number flashing and a beep prompt
(the light of the ON/OFF
button will flash once meaning
the motion sensor was activated
and sent the wireless signal)
ON/OFF
( twice)press

Step 4
Activate the again to confirm the sensor has been
added to the plug-in alarm receiver already.
sensor
Step 5
total 35 melodies optional.
Press “Melody” once to choose the melody for this sensor,
Melody
Step 6
Same steps to add more sensors to the plug-in receiver.
(For example: add the 2nd sensor to the receiver)
Press and hold the “Volume button” for 5 seconds
-----release the button when the Zone 2 flashing slowly
(zone 1 lights up meaning one sensor has been added
to zone 1 already)----activate the 2nd sensor once
----Zone 2 flashing quickly and a ring tone prompt
meaning the 2nd sensor has been added to the receiver.
Note please: the receiver has 4 zones and up to 4 sensors
can be added to 1 receiver.(the receiver will have a long
beep prompt if you operate to add more than 4 sensors
to 1 receiver)
4

5
Melody
Step 1
Plug the receiver into an outlet
Step 2
Press and hold both the “Volume” button and “Melody”
button for 10 seconds and release the
buttons when you heard a long beep prompt;
Note: all the sensors will be deleted by this operation.
Step 1
Plug the receiver into an outlet
Step 2
Press the “Volume” once to adjust the volume of the receiver.
(total 4 volume levels adjustable)
Volume
Volume
(3)How to adjust the alarm volume
(2)How to delete the sensors of the receiver

HB201911-806A(1.1)-01
48mm
34mm
5. Technical Parameters
(4)How to change the melody for the sensors
(each zone of the receiver has 35 optional melodies)
Step 1
Plug the receiver into an outlet
Step 2
Activate the sensor first,and then press the “Melody” button
to choose the melody for this sensor
Same steps for other sensors which have been added to
the receiver already.
Plug-in Alarm Receiver
Technical parameters
Static Current 20mA; Alarming Current 300mA
Working Current
AC 110V-220V
433MHz FSK+FHSS
Technical Parameters
Working Voltage
Wireless Frequency
Item
88mm
88mm
After-sale Service
E-mail:[e-mail]
6