Ezviz T3C User manual

1
Overview
1� Package Contents
Smart Button (x1) Double-sided Tape (x2)
Pin (x1)
Regulatory Information
(x1) Quick Start Guide (x1)
·The device appearance is subject to the actual one you have bought.
·The pin is only supplied for the device with reset hole.
2� Basics
Button
Cover Detaching Convex
Cover Detaching Groove
Antiskid Ring
Front Back
RESET
Hole
Insulation
Strip
Battery
LED
Indicator
RESET
Button
Insulation
Strip
Battery
LED
Indicator
Structure1(with reset hole) Structure 2(with reset button)
Name Description
Button Press the button once, twice or press and hold the button, the
custom operations or scenes on the app can be performed.
RESET Hole
(RESETButton)
Use the pin to press and hold the RESET hole for 2s (If your device
has a reset button, please press and hold the RESET button for
over 5s), the smart button will restart and then enter device adding
mode.

2
LED Indicator
• Fast-flashing Blue: Enters device adding mode.
• Fast-flashing Blue and then off: Added to the Gateway
successfully.
• Fast-flashing Blue and then off in 180 seconds: Failed to be
added to the gateway.
Get the EZVIZ App
1. Connect your mobile phone to Wi-Fi (suggested).
2. Download and install the EZVIZ app by searching for “EZVIZ” in the App Store
or Google PlayTM.
3. Launch the app and register an EZVIZ user account.
EZVIZ App
If you have already used the app, please make sure that it is the latest version. To find
out if an update is available, go to the app store and search for "EZVIZ".
Preparations
1� Remove Cover
Remove the cover of the smart button by turning the antiskid ring
counterclockwise as shown in the gure below.
2� Remove Insulation Strip
Remove the battery insulation strip as shown in the gure below.
Insulation Strip Insulation
Strip
Structure 1(with reset hole) Structure 2(with reset button)
• If you need to replace the battery, please purchase one CR2032 210mAh.
• When replacing batteries, please insert with the positive side facing up.
• Keep your hands dry and clean when touching the circuit board.

3
Add Device
The smart button should be used along with EZVIZ Zigbee Smart Gateway (afterinafter
referred to as "gateway"). Please add gateway to the EZVIZ Cloud by referring to the gateway
user manual, and then add the smart button to the gateway.
1� Method One: Add by Scanning QR Code
1. Log in to your account through EZVIZ app, tap the device adding icon and then
the QR code scanning interface will be displayed.
2. Scan the QR code on the user manual, and then add the smart button to the
gateway.
Scan QR Code
3. Add the smart button to the gateway by following the wizard on the app.
4. Align the cover detaching convex with the cover detaching groove as shown in
the gure below. Rotate the cover clockwise to tighten cover.
2� Method Two: Add by the Gateway
When adding smart button by the gateway, place the smart button as close to the gateway
as possible.
1. Make the gateway enter device adding mode as instructed by the user manual
of the gateway
2. Use the pin to press and hold the RESET hole for 2s (If your smart button has
a reset button instead of the reset hole, please press and hold the reset button
for 5s) until the indicator on the smart button turns fast-ashing blue, and the
smart button enters adding mode.
3. The smart button will be added to the gateway automatically.
4. Align the cover detaching convex with the cover detaching groove as shown in
the gure below. Rotate the cover clockwise to tighten the cover.

4
Installation
• The smart button can be put on the table, or be sticked on where you want through the
double-sided tape on the cover of the smart button.
• When choose wall mount, please mount the device on the wall below 1.5 meters.
1� Put on the table
Fig� 1 Put on the table
2� Stick at Where You Want
Fig� 2 Stick at where you want

5
• Do not install the smart button on metal doors because metal will cause signal
attenuation. You can install it on walls beside metal doors.
• It is recommended that the distance between the smart button and gateway be less than
20m. If there are walls between them, the number of walls should be no more than 2.
• Before sticking the smart button, clean the dust on the surface first. Do not stick the smart
button on limewashed walls.
BATTERY INSTALLATION and REPLACEMENT
1� Install Battery
Tear off the battery insulation, put the battery into the baseplate and insert it to the
end.
2� Replace Battery
Remove the battery from baseplate and replace battery with the Lithium Battery
CR2032 purchased by a regular manufacturer. Test the device for correct operation
whenever the baterries are replaced after re-fitting the device onto the base plate.
If the device is not working properly, please add the device and configurate the
network again by following the steps in Setup part or directly contact our technical
support.
• Risk of explosion if the battery is replaced by an incorrect type.
• Improper replacement of the battery with an incorrect type may defeat a safeguard(for example, in
the case of some lithium battery types).
• Do not dispose of the battery into fire or a hot oven, or mechanically crush or cut the battery, which
may result in an explosion.
• Do not leave the battery in an extremely high temperature surrounding environment or extremely
low air pressure, which may result in an explosion or the leakage of flammable liquid or gas.
• Dispose of used batteries according to the instructions.
• identifies the battery holder itself and identifies the positioning of the cell(s) inside the
battery holder.
• "+" identifies the positive terminal(s) of device which is used with, or generates direct current, "-"
identifies the negative terminal(s) of device which is used with, or generates direct current.
3� Removable Lithium ion Battery(CR2032)
Chemical Name CAS No� % wt�
Manganese dioxide 1313-13-9 30
Graphite 7782-42-5 1.2
Carbon black 1333-86-4 1.2
Polytetrafluoroethylene 9002-84-0 1.0
Lithium 7439-93-2 2.6
Propylene Carbonate-solvent 108-32-7 2.3
1,2 Dimethoxyethane-solvent 110-71-4 2.1
Lithium salt 7791-03-9 2.4
Polypropylene (PP) 9003-07-0 4.2
Stainless steel 12597-68-1 53

6
Operations on the EZVIZ App
The app interface may be different due to version update, and the interface of the app you
installed on your phone shall prevail.
1� Homepage
Launch the EZVIZ app, open the homepage of the related gateway, you can manage
your detector as needed on the page.
Log Detection log of the detector.
2� Settings
Parameter Description
Device Name Customize the name of your device.
Emergency Button When enabled, the device will switch to emergency call
mode and the original arm and disarm button will be
disabled.
Related Devices You can see the gateway connected to your detector.
Device Information You can see the device information here.
Share Share your device.
Delete Device Tap to delete the detector from EZVIZ cloud.