MOVITEC WL-250 User manual

USER MANUAL
MOVITEC
WL-250

2
MOVITEC WL-250
Table of contents
1. Safety.............................................................................................................................. 3
1.1 Safety instructions..................................................................................................... 3
1.2 Operating determinations.......................................................................................... 4
2. Introduction ................................................................................................................... 5
2.1 Features....................................................................................................................5
2.2 Beampath.................................................................................................................. 5
2.3 Description of device................................................................................................. 6
3. Installation ..................................................................................................................... 7
3.1 Fitting the lamp ........................................................................................................ 7
3.2 Rigging the fixture ..................................................................................................... 8
3.3 Connection to the mains ........................................................................................... 9
3.4 DMX-512 connection/connection between fixtures ................................................... 9
4. DMX-Protocol............................................................................................................... 10
4.1 Function of the control channels - 16 bit protocol ................................................... 10
4.2 Function of the control channels - 8 bit protocol ..................................................... 12
5. Addressing...................................................................................................................12
6. Remotely controllable functions................................................................................ 13
6.1 Lamp....................................................................................................................... 13
6.2 Switching On and Off the lamp by Control Board ................................................... 13
6.3 Colour wheel ........................................................................................................... 13
6.4 CMY - colours mixing system.................................................................................. 13
6.5 Beam effects........................................................................................................... 13
6.6 Dimmer ................................................................................................................... 13
6.7 Shutter/Strobe......................................................................................................... 13
6.8 Fan.......................................................................................................................... 13
7. Control Board .............................................................................................................. 14
7.1 Main functions......................................................................................................... 14
7.2 SPEC -Special functions......................................................................................... 15
8. Error and information messages ............................................................................... 18
9. Technical specifications ............................................................................................. 19
10. Maintenance and cleaning........................................................................................ 20
11. Appendix ....................................................................................................................21

3
CAUTION!
Keep this device away from rain and moisture!
Unplug mains lead before opening the housing!
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE YOU INITIAL START - UP!
1. Safety
1.1 Safety instructions
Every person involved with installation and maintenance of this device have to:
- be qualilfied
- follow the instructions of this manual
Caution ! Be careful with your operations.
With a voltage of 230V you can suffer
a dangerous electric shock when touching the wires!
Thisdevicehasleftour premises inabsolutely perfect condition.In order tomaintain this conditionand to ensure
asafe operation, itis absolutely necessaryfor the userto follow thesafety instructions andwarning notes written
in this manual.
Important:
Themanufacturer willnot acceptliability for anyresulting damagescaused bythe non-observance ofthis manual
or any unauthorized modification to the device.
Please consider that damages caused by manual modifications to the device are not subject to warranty.
Never let the power-cord come into contact with other cables! Handle the power-cord and all connections with
the mains with particular caution!
Make sure that the available voltage is not higher than stated on the rear panel.
Always plug in the power plug least. Make sure that the power-switch is set to OFF-position before you connect
the device to the mains. The power-plug has to be accessable after installing the device.
Make sure that the power-cord is never crimped or damaged by sharp edges. Check the device and the power-
cord from time to time.
Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the power-
cord by the plug. Never pull out the plug by tugging the power-cord.
This device falls under protection class I. Therefore it is essential to connect the yellow/green conductor to earth.
The electric connection, repairs and servicing must be carried out by a qualified employee.
Do not connect this device to a dimmer pack.
Do not switch the fixture on and off in short intervals as this would reduce the lamp’s life.
During the initial start-up some smoke or smell may arise. This is a normal process and does not necessarily
mean that the device is defective.
Do not touch the device’s housing bare-handed during its operation (housing becomes hot)!
For replacement use lamps and fuses of same type and rating only.
CAUTION ! EYEDAMAGES !
Avoid looking directly into the light source
(meant especially for epileptics) !

4
1.2 Operating determinations
This device is a moving-head spot for creating decorative effects. This product is only allowed to be operated
with an alternating current of 230 V, 50 Hz and was designed for indoor use only.
If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on
immediately. The arising condensation water might damage your device. Leave the device switched off until it
has reached room temperature.
Never run the device without lamp!
Do not shake the device. Avoid brute force when installing or operating the device.
Never lift the fixture by holding it at the projector-head, as the mechanics may be damaged. Always hold the
fixture at the transport handles.
Whenchoosing the installation-spot, pleasemake sure that the deviceis not exposed toextreme heat, moisture
or dust. There should not be any cables lying around. You endanger your own and the safety of others!
The minimum distance between light-output and the illuminated surface must be more than 1 meter.
Make sure that the area below the installation place is blocked when rigging, derigging or servicing the fixture.
Always fix the fixture with an appropriate safety-rope. Fix the safety-rope at the correct holes only.
Onlyoperate the fixtureafter having checkedthat the housingis firmly closedand all screwsare tightly fastened.
The lamp must never be ignited if the objective-lens or any housing-cover is open, as discharge lamps may
explose and emit a high ultraviolet radiation, which may cause burns.
Themaximum ambient temperature t
a
= 45° C mustnever be exceeded.Otherwise, the lamp isswitched offand
the fixture is out of operation for 5 minutes.
CAUTION!
The lens has to be replaced when it is obviously damaged,
so that its function is impaired, e. g. due to cracks or deep scratches!
Operate the device only after having familiarized with its functions. Do not permit operation by persons not
qualified for operating the device. Most damages are the result of unprofessional operation!
CAUTION!
The lamp has to be replaced when it is damaged
or deformed due to the heat!
Please use the original packaging if the device is to be transported.
Please consider that unauthorized modifications on the device are forbidden due to safety reasons!
If this device will be operated in any way different to the one described in this manual, the product may suffer
damages and the guarantee becomes void. Furthermore, any other operation may lead to dangers like short-
circuit, burns, electric shock, burns due to ultraviolet radiation, lamp explosion, crash etc.

5
2. Introduction
Unpack your MOVITEC WL-250 and make sure that there are no damages caused by transportation. Should
there be any, please consult your local dealer and do not take the device into operation.
2.1 Features
Moving-head spot with washlight
CMY colour mixture • Motorised colour wheel with additional 6 discrete dichroic filters plus open • Colours: red,
green, blue, 3200K and 5600K corrections filters, black-light (UV) • Colour-wheel continuous rotation (rainbow
effect) in both directions • Shutter unit allowing very fast blackout function and strobo effect 1-10 flash per sec.
• Dimmer unit very smooth dimming • Wide and flat beam can steplessly be rotated by 90° • Frost filter for softer
beam • Manually adjustable beam angle from 8° to 22° • Modular construction of fixture • Addressing, special
functions setting, effects calibration via control panel with 4-digit LED display • Readout fixture and lamp usage,
receiving DMX values, temperature, etc • Built-in analyzer for easy fault finding, error messages • Remotely
switching of the lamp • Built-in demo sequences • Preprogrammed variable/random strobe and dimmer pulse-
effects • Macro-function for CMY colour combinations • Black-out while Head moving or colour changing •
Remotely controllable speed of Pan/Tilt movement for easy programming • Remote reset function • Intelligent
control panel with 4-digit LED display • Silent fans cooling; remotely controllable speed of fans • 16 DMX-
channels - 16 bit Pan/Tilt movement resolution • 14 DMX-channels - 8 bit Pan/Tilt movement resolution • Pan-
movement range 530° • Tilt-movement range 280° • 8/16 bit movement resolution • Automatic Pan/Tilt position
correction • High luminous-efficiency parabolic reflector • Fresnel lens of diameter 150 mm • 9 high-quality
stepper-motors for smooth movements • Self-resetable thermo-fuse • For MSD/HSD 230V/250W GY-9.5 or
MSD/HSD 230V/200W GY-9.5 lamp • DMX-control via every standard DMX-controller •
2.2 Beampath
Min. beam angle 8° Max. beam angle 22°
Beam opening (m)
Beam opening (m)
Distance (m)
Diameter(m)
Distance (m)
Diameter (m)

6
1- Moving Head
2 - Yoke
3 - Base
4- Carring handles
Rear panel:
5- Power-switch
6- DMX output
7- DMX input
8 - Powercord
9 - Fuseholder
Front panel:
10 - Mode-button
11 - Enter-button
12 - Up-button
13 - Down-button
14 - Display
2.3 Description of device

7
3. Installation
3.1 Fitting the lamp
DANGER !
Install the lamps with the device switched off only.
Unplug from mains before !
To insert the lamp MSD 230V/250W or MSD 230V/200W open the small cover at the rear of head (See the
drawings) by loosening the 2 Phillips screws on the cover.
Gently pull out the lamp assemby.
If changing the lamp, remove the old lamp from the socket. Insert the lamp to the socket.
Do not install a lamp with a higher wattage! A lamp like this generates temperatures the device is not designed
for.
Damages caused by non-observance are not subject to warranty. Please follow the lamp manufacturer‘s notes!
Do not touch the glass-bulb bare-handed during the installation! Make sure that the lamp is installed tightly into
the lampholder system.
Reinsert the lamp assemby and tighten 2 screws again.
Before striking the lamp, reset the "LAti" counter in the main menu of the Control Board, by pressing the "Up"
and "Down" buttons in one time and then confirming with the Enter-button.
Do not operate this fixture with opened housing-cover!
Lamp adjustment of MOVITEC WL-250
The MOVITEC WL-250 lampholder is aligned at the factory.
Duetodifferencesbetweenlamps,fineadjustmentmay improve
light performance.
Strike the lamp and focus the light on a flat surface (wall).
Center the hot-spot (the brightest part of the beam) using the
3 adjustment screws „A, B, C”. Turn one screw at a time to
drag the hot-spot, diagonally across the projected image. If
you cannot detect a hot -spot, adjust the lamp until the light is
even.
Toreduce ahot-spot, pullthe lampin byturning allthree screws
„A, B, C” clockwise 1/4-turn at a time until the light is evenly
distributed.
If the light is brighter around the edge than it is in the center, or
if light output is low, the lamp is too far back in the reflector.
„Push” the lamp out by turning the screws „A, B, C”
counterclockwise1/4-turn ata timethe lightis brightand evenly
distributed.
Lamp assembly
2 phillips screws
screws „A, B, C”

8
3.2 Rigging the fixture
Danger of fire !
When installing the device, make sure there is no highly inflammable
material (decoration articles, etc.) in between a distance of min. 0,5 m.
Warning ! Use 2 clamps to rig the fixture on the truss.
Follow the instructions mentioned at the bottom of the base.
Make sure that the device is fixed properly! Ensure that
the structure (truss) to which you are attaching the fixtures is secure.
TheWL-250 can beplaced directly onthe stage floor
orrigged inany orientation ona truss withoutaltering
its operation characteristics (see the drawing).
Thefixture’sbase enablestobe mountedintwo ways.
Use the clamps with screws M10.
Install a safety wire that can hold at least 10 times
the weight of the fixture. Never use the carrying
handles for secondary attachment.
Secure chain
Clamp

9
3.3 Connection to the mains
Connect the fixture to the mains with the enclosed power-plug.
The earth has to be connected!
The occupation of the connection-cables is as follows:
Cable Pin International
Brown Live L
Blue Neutral N
Yellow/Green Earth
3.4 DMX-512 connection/connection between fixtures
The wires must not come into contact with each other, otherwise
the fixtures will not work at all, or will not work properly.
Only use a stereo shielded cable and 3-pin XLR-plugs and connectors in order to connect the controller with the
fixture or one fixture with another.
Occupation of the XLR-connection:
DMX - output DMX-input
XLR mounting-socket: XLR mounting-plug:
If you are using the standard controllers, you can connect the DMX-output of the controller directly with the
DMX-input of the first fixture in the DMX-chain. If you wish to connect DMX-controllers with other XLR-outputs,
you need to use adapter-cables.
Building a serial DMX-chain:
Connect the DMX-output of the first fixture in the DMX-chain with the DMX-input of the next fixture. Always
connect one output with the input of the next fixture until all fixtures are connected.
Caution: At the last fixture, the DMX-cable has to be terminated with a terminator. Solder a 120 Wresistor
between Signal (–) and Signal (+) into a 3-pin XLR-plug and plug it in the DMX-output of the last fixture.
1- Ground
2 - Signal (-)
3 - Signal (+)
1- Ground
2 - Signal (-)
3-Signal (+)

10
4. DMX-Protocol
4.1 Function of the control channels - 16 bit protocol
4.1.1 Channel 1 - Pan
Push slider up in order to move head horizontally (PAN).
Gradualhead adjustmentfrom oneend ofthe sliderto theother
(0-255, 128-center). The head can be turned by 530° and
stopped at any position you wish.
4.1.2 Channel 2 - Pan fine 16bit
4.1.3 Channel 3 - Tilt
Push slider up in order to move head vertically (TILT).
Gradualhead adjustmentfrom oneend ofthe sliderto theother
(0-255, 128-center). The head can be turned by 280° and
stopped at any position you wish.
4.1.4 Channel 4 - Tilt fine 16bit
4.1.5 Channel 5 - Speed of PAN / TILT movement
0 Max speed (tracking mode)
1 Max speed (vector mode)
249 Min. speed (vector mode)
250-255 Max. speed, black-out while PAN, TILT moving
or color changes (tracking mode)
4.1.6 Channel 6 - Switch On / Off the lamp, reset, speed control of cooling fan
0 open, max. speed of fan
127 open, min. speed of fan (silent operation) from 0 to 127
- decreasing speed of fan
128 - 139 Switch On the lamp, reset, open position
140 - 239 No function
230 - 239 Switch Off the lamp after 3sec.
240 - 255 No function

11
4.1.7 Channel 7 - Colour wheel
0 - 17 Open/white
18 - 35 Red
36 - 53 Blue
54 - 72 Green
73 - 90 CTF 3200K
91 - 108 CTF 5600K
109 - 127 UV filter
128 - 190 Forwards rainbow effect from fast to slow
191 - 192 No rotation
193 - 255 Backwards rainbow effect from slow to fast
4.1.8 Channel 8 - Cyan
0 - 255 Cyan (0 - white, 255 - full cyan)
4.1.9 Channel 9 - Magenta
0 - 255 Magenta (0 - white, 255 - full magenta)
4.1.10 Channel 10 - Yellow
0 - 255 Yellow (0 - white, 255 - full yellow)
4.1.11 Channel 11 - Speed of CMY and Dimmer
0 Max speed
255 Min speed
4.1.12 Channel 12 - Colours macros - CMY and colour wheel
0 - 7 Off 128 - 135 Macro 16
8 - 15 Macro 1 136 - 143 Macro 17
16 - 23 Macro 2 144 - 151 Macro 18
24 - 31 Macro 3 152 - 159 Macro 19
32 - 39 Macro 4 160 - 167 Macro 20
40 - 47 Macro 5 168 - 175 Macro 21
48 - 55 Macro 6 176 - 183 Macro 22
56 - 63 Macro 7 184 - 191 Macro 23
64 - 71 Macro 8 192 - 199 Macro 24
72 - 79 Macro 9 200 - 207 Macro 25
80 - 87 Macro 10 208 - 215 Macro 26
88 - 95 Macro 11 216 - 223 Macro 27
96 - 103 Macro 12 224 - 231 Macro 28
104 - 111 Macro 13 232 - 239 Macro 29
112 - 119 Macro 14 240 - 247 Macro 30
120 - 127 Macro 15 248 - 255 Macro 31

12
4.1.13 Channel 13 - Effect wheel
0 - 70 Full beam
71 - 230 Beam shaper
231 - 255 Frost filter
4.1.14 Channel 14 - No function
4.1.15 Channel 15 - Shutter, Strobe
0 - 31 Shutter closed
32 - 63 No function (shutter open)
64 - 95 Strobe-effect from slow to fast (max. 10 flashes/second)
96 - 127 No function (shutter open)
128 - 159 Pulse-effect in sequences
160 - 191 No function (shutter open)
192 - 223 Random strobe-effect from slow to fast
224 - 255 No function (shutter open)
4.1.16 Channel 16 - Dimmer intensity
0 - 255 Intensity from 0 to 100 %
4.2 Function of the control channels - 8 bit protocol
5. Addressing
The control board on the front panel of the MOVITEC WL-250 allows you to assign the DMX fixture address,
which is defined as the first channel from which the MOVITEC WL-250 will respond to the controller.
If you set, for example, the address to channel 5, the MOVITEC WL-250 will use the channel 5 to 20 for control.
Please, be sure that you don’t have any overlapping channels in order to control each MOVITEC WL-250
correctly and independently from any other fixture on the DMX data link.
If two, three or more MOVITEC WL-250 are addressed similarly, they will work similarly.
For address setting follow this procedure:
1. Switch On the MOVITEC WL-250 and wait until the fixture reset has finished ("rSt” is flashing at the display).
2. Press the [Mode] key in order to access the main menu. Browse through the menu by pressing the [Up]
and [Down]keysuntil the displayshows "A001”. Confirm by pressing [Enter] keyand the letter"A” will flash.
3. Use the [Up] and [Down] keys to select the desired address.
4. Confirm by pressing [Enter] or [Mode] to cancel.
Controlling:
After having addressed all MOVITEC WL-250 , you may now start operating these via your lighting controller.
Note: After switching on, the WL-250 will automatically detect whether DMX 512 data is received or not.
If thereis nodata receivedat theDMX-input, thedisplay willstart to flash "A001” with actuallyset address.
This situation can occurr if:
- the 3 PIN XLR plug (cable with DMX signal from controller) is not connected with the input of the WL-250
- the controller is switched off or defective, if the cable or connector is defective or the signal wires are
swap in the input connector.
Note: It’s necessary to insert the XLR termination plug (with 120 Ohm) in the last lighting in the link in order to
ensure proper transmission on the DMX data link.

13
6. Remotely controllable functions
6.1 Lamp
The MOVITEC WL-250 is run with a MSD 250W/200W lamp.
A relay inside of the MOVITEC WL-250 allows you to switch On and Off the lamp via itself control board on the
top side or via your controller without affecting the rest of the lighting.
6.2 Switching On and Off the lamp by Control Board
1. Switch On the MOVITEC WL-250 and wait until the fixture reset has finished.
2. Press the [Mode] key in order to access the main menu. Browse through the menu by pressing the [Up] and
[Down] keys until the display shows "LAMP”. Confirm by pressing [Enter] key.
3. Use the [Up] and [Down] keys to select "On" for switch On the lamp and "Off” for switch Off the lamp and
press [Enter] to confirm or [Mode] to cancel.
Note: It is also important to note, that the discharge lamp is cold restrike types, that means, that they have to be
cold before re-striking. For this reason, you have to wait 5 minutes (max. speed of fan must be adjusted) after
having switched Off the lamp before you can switch it back On again. If you try to switch On the lamp within 5
minutes after having switched it Off, the MOVITEC WL-250 will store this information and automatically ignite
the lamp when the 5 minutes period has expired. The message "HEAt” will appear on the control board display
at the back side of the MOVITEC WL-250. If the ignition of the lamp is seven times unsuccessful, on the display
will appear "LA.Er”,meaningthatthelampcouldbedamagedorevenmissed,ortherecouldbeafailureontheignitor
orballast.
6.3 Colour wheel
The MOVITEC WL-250 features a colour-wheel with 7 color positions - 6 of these with dichroic colors and the
lastoneopen. Itis alsopossible torotatethe color-wheelcontinuously atdifferentspeeds -theso-called "Rainbow
effect“ is created.
6.4 CMY - colours mixing system
The CMY color mixing system is based on graduated cyan, magenta, and yellow color filters. A continuous
range of colors may be achieved by varying the amount of each filter from 0 to 100%.
6.5 Beam effects
The beam shaper allow you to widen and flatten beam. Beam shaper rotates 180°.
Frost filter on the same wheel as beam shaper softens the beam.
6.6 Dimmer
Smooth 0 - 100 % dimming is provided by the special dimmer unit.
6.7 Shutter/Strobe
Extremely fast shutter may also be used for strobe effect (1 - 10 flashes per second)
6.8 Fan
The MOVITEC WL-250 is cooled by free axial fans - two in the projector head and one in the base. The speed
of the fan (and of course the noise) can be continuously reduced if very quiet performance is required.
By the Control Board using the „FAnS” function you can choose 4 types of low fan speed operating:
1. "High” - high (max) speed of fans
The cooling fans work on max. speed (max. cooling)
2. "reg” - continuous controlling of the fan speed
the fan automatically raises its speed in order to control inside temperature of the lighting, if the
temperatureinside increasesabout certain level(the lowfan speed reducesthe coolingof the lighting).
This cycle can repeat several times until the temperature inside is on suitable level.
3. "loof” - low speed/Switch Off the lamp operating
the fan keeps the adjusted low speed until the temperature exceeds max. inside temp. then the
MOVITEC WL-250 automatically switch Off the lamp.
4. "lohi” - low/high speed of the fan operating
the fan keeps the adjusted low speed until the temperature exceeds max. inside temp. of the fixture,
then the MOVITEC WL-250 automatically switch from low to high the fan speed.

14
7. Control Board
The control board situated on the front panel of the MOVITEC WL-250 offers several features. You can simply
setthe lighting address, read the numberof lamp or unit hours, switchOn and Off thelamp, run test show,make
a reset and also use special functions for manual, demo and service purposes.
The main menu is accessed by pressing the [Mode] key - press this one so many times until the display shows
message "A001" (with actually stored address). Browse through the menu by the pressing [Up] and [Down]
keys- the display showsstep by step these messages:A001, rPAn, rTilt, 16br, Lati, Poti, LAMP, dEMo, rESE,
SPEC. Press [Enter] if you wish to select one of them. The functions provided are described in the following
sections and the function hierarchy is shown below.
7.1 Main functions
- DMX 512 Address settings
The letter "A" flashes. Use the [Up] and [down] keys to select required address (001 - 496) and press [Enter]
to confirm or [Mode] to cancel and return to the main menu.
- Pan reverse
This function allows you to invert the pan movement. Use the [Up] and [Down] keys to select "On" if you wish
this feature or "Off" if you don’t wish this feature and press [Enter] to confirm or [Mode] to cancel and return to
the main menu.
- Tilt reverse
This function allows you to invert the tilt movement. Use the [Up] and [Down] keys to select "On" if you wish
this feature or "Off" if you don’t wish this feature and press [Enter] to confirm or [Mode] to cancel and return
to the main menu.
- Movement resolution
By this function you can adjust the desired movement resolution 8 or 16 bit. Use the [Up] and [Down] keys to
select ‘On’ if you wish the 16bit high resolution or "Off" if you wish only 8 bit resolution and press [Enter] to
confirm or [Mode] to cancel and return to the main menu.
Note: Ifyou adjust the16 bit resolutionthe fixture willoccupy 16 DMXchannels, if youadjust the 8bit resolution,
the fixture will be operated by only 14 DMX channels. Please, check the DMX protocol.
- Lamp On time
This option enables you to read the total number of hours that the lamp has been powered On. Press [Enter] or
[Mode] to return to the main menu. In order to reset the counter to 0, you have to hold the [Up] and [Down]-
button and press the [Enter]-button.
- Power On time
By this option you can read the total number of hours that the MOVITEC WL-250 has been powered On. Press
[Enter] or [Mode] to return to the main menu.
- Switch On/Off the lamp
Use the [Up] and [Down] keys to select "On" if you wish the switch On the lamp or "Off" if you wish switch Off
the lamp and press [Enter] to confirm or [Mode] to cancel and return to the main menu.

15
- Demo sequences
Thisfunction allowsyou to runa special demo-testsequences without anexternal controller,which willshow you
some possibilities of using WL-250. Press [Up] and [Down] keys to select the "Mod1" or "Mod2" sequences.
The "Mod1" is suitable for projections on the wall, ceilling or ground without any head-movement, the "Mod2"
uses all WL-250 functions and therefore is good for a complete introduction of the fixture.
- Reset Function
Press [Enter] key to run reset. This option enables the MOVITEC WL-250 to index all effects (functions) and
return to their standard positions.
7.2 SPEC -Special functions
Use the [Up] and [Down] keys to browse through the special functions and select the one by pressing [Enter].
- Manual control of effects
This function allows you to control manually the channel functions of the fixture. Use the [Up] and [Down] keys
to select desired function and press [Enter] to adjust the effect or [Mode] to cancel and return to the menu.
- Lamp On automatically
This function enables to switch On the lamp automatically after switching On the fixture. Use the [Up] and
[Down] keys to select "On” if you wish to switch On the lamp automatically after switching On the fixture or
"Off” ifyou wish thecamp offafter switchingOn the fixture andpress [Enter] to confirm or[Mode] to canceland
return to the menu.

16
- DMX values
Readout DMX values of each channel received by the fixture. Use the [Up] and [Down] keys to select desired
channel and press [Enter] to read its value coming to the fixture or [Mode] to cancel and return to the menu.
- Automatic blackout of Display
This function allows you to keep the display On or to turn Off automatically 2 minutes after last pressing any key
on the control board. Use the [Up] and [Down] keys to select "On" if you wish to keep the display On or "Off"
if you wish to turn Off automatically 2 minutes after last pressing any key on the control board and press [Enter]
to confirm or [Mode] to cancel and return to the menu.
- Display intensity
By this function you can adjust from 20% to 100% the intensity of the display. Use the [Up] and [Down] keys to
select the level of the display intensity and press [Enter] to confirm or [Mode] to cancel and return to the menu.
- Lamp Off via DMX
This function allows you to switch Off the lamp by DMX. Use the [Up] and [Down] keys to select "On" if you
want to switch Off the lamp by DMX or "Off" if you don’t want to switch Off the lamp by DMX and press [Enter]
to confirm or [Mode] to cancel and return to the menu.
- Temperature
Temperature readouts of fixture inside in Celsius. Inside temperatures below 70° C are not critical. 70° C and
more lead to the lamp being switched off. Please note that the outside temperature should not exceed 45° C.
-Low fan speed operating
By using this function you can choose 3 types of low fan speed operating. Browse through this menu by the
pressing[Up] and [Down] keys - thedisplay shows step by step thesemessages: "HIGH, reG, LoOF, Lo.HI,".
Press [Enter] if you wish to select one of them or [Mode] to cancel and return to the menu.
- high (max) speed of fans
The cooling fans work on max. speed (max. cooling)
- continuous controlling of the fan speed
the fan automatically raises its speed in order to control inside temperature of the lighting,
if the temperature inside increases about certain level (the low fan speed reduces the cooling of the
lighting). This cycle can repeat several times until the temperature inside is on suitable level.
- low speed/Switch Off the lamp operating
the fan keeps the adjusted low speed until the temperature exceeds max. inside temp.. then the
MOVITEC WL-250 automatically switch Off the lamp.
- low/high speed of the fan operating
the fan keeps the adjusted low speed until the temperature exceeds max. inside temp..of the fixture,
then the MOVITEC WL-250 automatically switch from low to high the fan speed.

17
- Default settings
Press [Enter] to reset all fixture personalities (not the adjusting functions) to the default values. On the display
will appear "rSt” meaning that the fixture makes the reset. See the table of personality setting and their default
positions.
- Adjusting the default positions of colour and CMY
By this function you can calibrate and adjust the colour and CMY to their standard/right positions. Use the [Up]
and [Down] keys to browse through the adjusting menu - the display shows step by step these messages:
"PAn, Tilt, SPEd, Colo, CYAn, MAGE, YELL, MACr, EFEC, Stro, dimr, FCAL" by which you can adjust the
fixture to the required/desired position (0-255) before the function calibration. Then when the positioning is
finished use the last "FCAL" function (Fixture calibration).
1. Calibration via the control board
Press [Enter] and the [Up] and [Down] keys in order to display the following messages: "Colo, CYAn, MAGE,
YELL," for very smooth function calibration. Select one of them, press [Enter] and use the [Up] and [Down]
keys in order to adjust their right value from 0 to 255. Then press [Enter] to confirm or [Mode] to cancel and
return to the menu. This can be repeated for each calibration parameter if it is required. When the calibration is
finished,it isnecessaryto usethe "ArES" functioninorder towrite thecalibration valuesto thememory (EPROM)
and to make a reset in order to check the newly adjusted positions of the colour and CMY wheels. When the
resetof the fixture isfinished, the displaywill show the "FCAL" message.Press [Enter] to repeat the calibration
or [Mode] to return to the "AdJ" menu.
Personality Display
Pan reverse
Tilt reverse
Movement
resolution
Lamp on
automatically
Automatic blackout
of display
Displayintensity
LampOffvia DMX
Low fan speed
operating
Default values
(SHADED)

18
2. Calibration via the external controller
Press [Enter] and the [Up] and [Down] keys in order to display the following messages: "Colo, CYAn, MAGE,
YELL" - calibration parameters. Select one of them and press [Enter].
Now you can calibrate the colour and CMY wheels by your controller. The DMX calibration protocol is described
in the table mentioned below.
DMX Calibration protocol:
After having calibrated required functions press [Enter] to confirm (or [Mode] to cancel and return to the menu
without reset by the "ArES" function) and use the "ArES" function in order to write the calibration values to the
memory (EEPROM) and to make a reset in order to check the new adjusted positions of the colour and CMY
wheels .
8. Error and information messages
This message appears if you try to switch on the lamp within 5 minutes after having switched it off (the lamp is
too hot). The message will appear on the display if the lamp doesn't ignite within 28 seconds. The MOVITEC
WL-250 will store this information and automatically ignite the lamp when the 5 minutes period has expired.
The ignition of the lamp is seven times unsuccessful (the HEAt message appeared six times before), and the
displayshows "LAEr", meaning thatthe lamp could bedamaged or even missed,the fixture is overheating(this
can occur if the ambient temperature is 45° C or more) or there could be a failure on the ignitor or ballast.
Please place or replace the lamp, check the ambient temperature or contact your dealer if the situation was not
caused by the lamp.
This messsage informs you that the main PCB does not communicate correctly with the Control Board.
(color-wheel error) This messsage will appear after the reset of the fixture if the magnetic-indexing circuit
malfunctions (sensor failed or magnet missing) or the stepping-motor is defective (or its driver circuit on the
main PCB). The color-wheel is not located in the default position after the reset.
This error message informs you that the fixture was overheating (occured if the ambient temperature is 45° C or
more)and that the relayswitched offthelamp. This messagewill appear on thedisplay until the temperaturewill
beon asuitable level, thenthe display willshow the HEAtmessage meaningthe lamp istoo hot (explanationsee
above).
This message appears if the lamp lighting sensor is failed. Please, contact your dealer.
This message will appear if the fixture was shortly disconnect from the main.
DMX
Channel 123 4 5678
Function COL. CYAN MAGENTA YELLOW - - COLOURS CYAN
CALIBRATION
0 - 255
CALIBRATION
0 - 255
CALIBRATION
0 - 255 --
STANDARD
PROTOCOL
STANDARD
PROTOCOL
910111213141516
MAGENTA YELLOW SPEED CMY,
DIMMER
COLOUR
MACROS
BEAM
EFFECTS - STROBO DIMMER
STANDARD
PROTOCOL
STANDARD
PROTOCOL
STANDARD
PROTOCOL
STANDARD
PROTOCOL
STANDARD
PROTOCOL -STANDARD PROTOCOL
STANDARD
PROTOCOL
SMOOTH MICROSTEP MOVEMENT

19
(PAN-yoke movement error) This message will appear after the reset of the fixture if the yoke’s magnetic-
indexing circuits malfunction (sensors failed or magnet missing) or the stepping motor is defective. (Or its
driving IC on the main PCB). The yoke is not located in the default position after the reset.
(TILT-head movement error) This message will appear after the reset of the fixture if the head’s magnetic-
indexing circuit malfunctions (sensor failed or magnet missing) or the stepping motor is defective. (Or its driving
IC on the main PCB). The head is not located in the default position after the reset.
It will appear if the frequency of the main is not standard 50 or 60Hz.
9. Technical specifications
Power supply
EU-model: 210/230/250V AC, 50/60Hz ~
Fuse: T 3.15A, 250V
US-model: 100/115/208/230 V AC, 50/60Hz ~
Fuse: T 6.3A,
Power consumption: 500W
Lamp
MSD/HSD 230 V/250W GY-9.5 or MSD/HSD 230V/200W GY-9.5
Colours
- CMY - colours mixing system
- 6 dichroic-filters plus white
- Colour-wheel with variable rotation speed
Beam effects
- Beam shaper
- Frost filter
Strobe
- Strobe effect with variable speed (1 - 10 flashes per second)
Dimmer
- Smooth dimmer from 0 - 100 %
Motor
- 9 high quality stepping-motors controlled by microprocessors
Electronics
- Digital serial input DMX-512
- 16 control-channels (full 16 bit protocol):
Channel 1: Horizontal mirror-movement 8 bit
Channel 2: Fine Horizontal mirror-movement 16 bit
Channel 3: Vertical mirror-movement 8 bit
Channel 4: Fine Vertical mirror-movement 16 bit
Channel 5: Pan/Tilt speed
Channel 6: Fan speed, On/Off lamp, reset
Channel 7: Colours wheel
Channel 8: Cyan
Channel 9: Magenta
Channel 10: Yellow
Channel 11: Speed of CMY and Dimmer
Channel 12: Colours macros - CMY and colour wheel
Channel 13: Beam effect
Channel 14: No function
Channel 15: Shutter, strobe
Channel 16: Dimmer

20
Pan/Tilt
Pan movement range 530°
Tilt movement range 280°
8/16 bit movement resolution
Automatic Pan / Tilt position correction
Maximum PAN-movement 530° in 2.65 s
Maximum TILT-movement 280° in 1.68 s
Rigging
Stands directly on the floor
Mounts horizontally or vertically with 2 clamps
2 truss orientation
Safety chain/cord attachment point
Temperatures
Maximum ambient temperature t
a: 45° C
Maximum housing temperature t
B(steady state): 80° C
Dimensions and weight
Length of base (including handles): 372 mm
Width of yoke: 426 mm
Height (head horizontal): 500 mm
Weight (net): 16 kg
Shippingweight: 25 kg
10. Maintenance and cleaning
It is absolutely essential that the fixture is kept clean and that dust, dirt and smoke-fluid residues must not build
up on or within the fixture. Otherwise, the fixture‘s light-output will be significantly reduced. Regular cleaning will
not only ensure the maximum light-output, but will also allow the fixture to function reliably throughout its life.
A soft lint-free cloth moistened with any good glass cleaning fluid is recommended, under no circumstances
should alcohol or solvents be used!
DANGER !
Disconnect from the mains before starting any
maintenance work
The fresnel lens will require weekly cleaning as smoke-fluid tends to building up residues, reducing the light-
output very quickly. The cooling-fans should be cleaned monthly.
The interior of the fixture should be cleaned at least annually using a vacuum-cleaner or an air-jet.
The dichroic colour-filters should be cleaned monthly.