Ayra TDC Acid User manual

TDC Acid
Kaleidoscopic Light Effect
User Manual
The information in this user manual is subject to change at any time without notice.
Version: 1.0 Date of creation and author's initials: 07-10-2019 RV Revision date and author's initials: -

Introduction
Thank you for purchasing the Ayra TDC Acid. This versatile, kaleidoscopic effect conjures multi-coloured
spectacles in every room, with or without mist. This manual provides all the information you need to know
about the product before you start using it.
e advise that you read this user manual in its entirety before unpacking the contents of the box, so that you
are familiar with all of the functionality that this product has to offer. Please be sure to check that all of the
parts and accessories listed below under 'Box Contents' are included in the package. In the event that the
Ayra TDC Acid does not function properly, or if you have any issues while operating it, please remove the
plug from the power socket and contact your retailer for assistance.
Inhoud doos:
- Ayra TDC Acid Fixture
- Suspension bracket
- Hardware (2x tightening knobs, 2x rubber rings)
- Connection cable from IEC C13 to Schuko, 1.5 mm²
Please inspect the device and included accessories
Should you discover that either the device or one or more of the included parts have been damaged or
rendered defective while in transit, please contact your dealer directly.
Please note that the pictures in this user manual serve illustrative purposes only and may differ from the
actual product.
The information in this user manual is subject to change at any time without notice.
Version: 1.0 Date of creation and author's initials: 07-10-2019 RV Revision date and author's initials: -

Safet Instructions
Everyone involved with the installation, operation and maintenance of this device must:
- Be qualified.
- Be skilled.
- Have read the instructions included in this user manual.
- Be sure that neither the device nor the included accessories are damaged. Should the device or the
included accessories be damaged, please contact your retailer for more information.
- Ensure that the device is in good working condition and is safe to operate. Please follow the advice and
instructions as they are described in this user manual.
Damage caused by misuse and/or modifications made to the device are not covered by the warranty.
This device does not contain any parts that can be repaired or replaced by the user. Should maintenance or
repairs be necessary, they must be handled by a qualified technician.
The light source of this device is not replaceable. If the light source no longer functions, the entire device
needs to be replaced.
Important information regarding health and safet :
- Do not remove any labels or stickers from this device.
- Do not leave any cables lying around.
- The device should not be opened up and any hardware or software that may be present should not be
modified.
- To achieve optimal performance, any inputs on the device should not be fed with a signal higher than
necessary.
- The device should only be used indoors; contact with water, rain and moisture should always be avoided.
Do not place any objects containing liquid on top of the device.
- Remove the device from any nearby flames or heat sources; do not place it near flammable fluids, gasses
The information in this user manual is subject to change at any time without notice.
Version: 1.0 Date of creation and author's initials: 07-10-2019 RV Revision date and author's initials: -
WARNING!
Keep this device awa from moisture, water and rain to avoid the chance of electric shocks!
WARNING!
Onl connect this device to a suitable power socket. This device functions on a specific power
voltage. If it is plugged into a power socket with a different voltage, it could result in permanent
damage and even dangerous situations such as fire or electric shocks.
WARNING!
Be careful when operating this device. Touching the wires that are connected to the mains,
inside or outside the device, could result in electric shocks!

or objects.
- Disconnect this device from a power source if it is not being used for a long period of time; if maintenance
is necessary, or if it needs to be cleaned.
– Do not pull or tug on the cable to remove a connector as this may cause damage.
- Do not use any cables other than the ones described in this manual. Do not use defective cables. Please
contact your retailer if the included or necessary cables do not function properly with this device.
- Only use this device with a stable AC power supply.
- Only use this device with power from a grounded power source.
- In the event that the device is exposed to extreme temperature changes (e.g. transported from a cold
outdoor environment into a warm indoor environment), it should not be turned on until it has reached room
temperature. This is necessary to prevent moisture (condensation) from forming inside the device, which
could lead to electric shocks.
Guidelines and operation of this device:
- This device is intended for use by professionals on stage, in theatres, in clubs and in similar entertainment
locations.
- This device is not suitable for use by children and should always be operated by an adult.
- This device is designed to create light effects for entertainment purposes. It is not suitable for household
illumination.
- This device may only be used in a suitable environment where no damage to the device can occur. Do not
use the device in moist or dusty environments such as:
- indoor swimming pools where chlorine is used
- beaches or any location where sand and/or salt is present
- outdoors
- indoors in spaces where intense heat sources are present, or where it can reach temperature levels
that would be considered uncomfortable for a person
- Avoid impact and collisions during use and transport. Do not move or transport the device while it is in use.
Avoid using excessive force when installing and operating the device.
- Any user must become familiar with the functions of this device before using it.
- Should the device not be used in the manner described in this user manual, damages or even injuries could
occur. Ayra cannot be held responsible for any injuries or damages that occur as a result of improper use of
t h i s p r o d u c t .
Storage and transport:
- This product was designed for mobile use. Please only transport the device in the original packaging, or in
a flight case with a suitable foam inlay.
- This device was not designed for permanent (24/7) use. The expected lifespan of the device will not be
affected by occasionally turning the device off. Disconnect the device or turn off the power when it is not
actively in use.
- If the device is not in use for a long period of time, it should be disconnected and stored in a dust-free
environment.
- Do not expose the device to extreme temperature differences.
Housing:
- Inspect the device's housing frequently and always just before use. Avoid operating the device if there are
any large dents or cracks, or if screws are missing. Do not use the device if the housing is not in good
condition.
Contact your dealer or a qualified technician if you are unsure about the state of the device.
- Check the device and the screws for corrosion. Corrosion must not be present on this device. Contact your
dealer or a qualified technician if you find any corrosion on the screws.
Every power and signal connector should be securely attached. Do not use the device if the connectors are
not secure.
- Avoid dust and dirt build-up. Clean the device once a month by disconnecting it from the power supply and
wiping it down with a dry or slightly moist cloth. If the device is used frequently, the cleaning intervals should
increase.
The information in this user manual is subject to change at any time without notice.
Version: 1.0 Date of creation and author's initials: 07-10-2019 RV Revision date and author's initials: -

S mbol explanation:
WEEE: Ensure that this device is disposed of properly. This product falls under the EEE
( aste Electrical and Electronic Equipment) directive. The requirements of this directive apply
to all manufacturers and producers of electronic devices in the EU. Do not throw this product
away with regular rubbish. Please contact your local authority for more information about how
to recycle and dispose of these products in your region. By recycling this product in the proper
manner, we can work together to ensure that we can continue to enjoy these kinds of
products and still protect the environment as much as possible from pollution.
CE: The CE logo indicates that this product meets the European norms and requirements to
which it must legally conform.
Suitable for indoor use onl : this product was only designed for indoor use. The maximum
environmental temperature must not exceed 40 degrees Celsius (104 degrees Fahrenheit).
Contact:
Ayra professional lighting products
Verrijn Stuartweg 18
4462 GE Goes
The Netherlands
Please do not send any products to this correspondence address.
Should you wish to send in a product for repairs or for a refund, please contact your dealer for an RMA
re uest (Return Merchandise Authorisation).
The information in this user manual is subject to change at any time without notice.
Version: 1.0 Date of creation and author's initials: 07-10-2019 RV Revision date and author's initials: -

Operation Guidelines for this Device
1. Suspension bracket with tightening knobs
2. Power output via IEC C13
3. Power input via IEC C14 with fuse compartment
4. Safety cable attachment point
5. Microphone
6. DMX input and output via 3-pins XLR
7. LED Display with Menu buttons
8. Ventilation fan
9. Light Output with adjustable lens
The information in this user manual is subject to change at any time without notice.
Version: 1.0 Date of creation and author's initials: 07-10-2019 RV Revision date and author's initials: -
2
5
6
7
9
1
3
4
8
1

Operation and Mounting
To activate the device, plug it into a mains socket. Once it's connected to an active power source, it will turn
on automatically.
The device cannot be operated while it is still starting up and displays the ‘AYRA’ logo. Once the device has
fully started up, it will automatically jump to the last mode and setting. Operation modes and other settings
shown on the display can now be adjusted or changed via the menu buttons.
If a DMX signal is detected, the device shall automatically switch to DMX mode and the DMX address that
was last used. For a new device, this is usually DMX address 001. The DMX address can of course be
changed via the display and menu buttons.
The functions, modes and settings can be changed by using the display and menu buttons. Push ‘Enter’ to
select a function or to confirm a change. Push ‘Up’ and ‘Down’ to change any values and push the ‘Menu’
button to return to the main menu. A few seconds after confirming a setting by pressing ‘Enter’, the device
shall automatically return to the main menu and perform the set actions. This can be sped up by holding the
‘Menu’ button down for 2 seconds after confirming a setting by pressing ‘Enter’. This is usually done after
adjusting the working mode or DMX address.
The Menu includes the following options and fuctions:
Displa Mode Function
A001 DMX Address Configuration Address A001 … A512
SLAV Slave Mode Slave
T000-T999 Temperature Display Displayed in Degrees Celsius
F00-F99 Stroboscope Speed / Auto Mode F00 = Static, F01-99 = slow to fast
D00-D99 Dimmer Level Auto Mode D00 = Off D99 = Maximum intensity
R000-R255 Prism Rotation Auto Mode R0-9 Stop
R10-120 Clockwise rotation, fast to slow
R121-R134 Stop
R135-R245 Anti-clockwise rotation, slow to fast
R246-255 Stop
G000-G255 Gobo heel Rotation Auto Mode G0-G63 Gobo selection
G64-G127 Gobo shake selection
G128-G189 Gobo wheel, clockwise rotation, fast
to slow
G190-193 Stop
G194-255 Gobo wheel, anti-clockwise rotation,
slow to fast
SP1 - SP9 Speed Auto Mode SP1 - SP9 (slow to fast)
SU00-99 Sensitivity 0 - 100: Sensitivity in %
An explanation of all available functions can be found below:
The information in this user manual is subject to change at any time without notice.
Version: 1.0 Date of creation and author's initials: 07-10-2019 RV Revision date and author's initials: -

ADDR: ith this function, you can determine the DMX start address of the device. Set it channel 001, and
the device will respond to DMX channel 1. Set it to channel 003, then the device will respond to DMX
channel 3 and so on.
SLAV: Using the Master / Slave Mode, it’s possible to connect several devices of the same type with one
another, via DMX 3-pin XLR cables so that they perform exactly the same movements and functions at the
same time. Therefore, single devices do not respond individually (or chaotically) and this results in a
completely coordinated show. In the Master / Slave function, the first device in the circuit is set as the Master
and does not receive DMX signal.
PLEASE NOTE: hen Slave mode is activated, the device shall wait for a signal from the designated Master
device. Selecting an automatic or sound-controlled mode is then not possible! To cancel the Slave mode,
enter the ‘SLAV’ menu and select ‘NAST’. This then sets the device to Master mode and the stand-alone
functions can then be activated once more.
T000-T999 The in-built temperature sensor registers the internal temperature of the device. The temperature
can be checked here and is displayed in Degrees Celsius.
Manual settings
This device has many included functions that can be manually set up. Here, shapes can be selected as well
as intensity and prisma rotation and speed.
F00-F99: This controls the possible flash speed. F00 is a static projection; F01 - F99 adjusts the flash speed
f r o m s l o w t o f a s t .
D00-D99: This controls the dimmer-intensity. 00 is equal to off and 99 is equal to the maximum possible
intensity.
R000-R255: This controls the prisma rotation. Here, the rotation speed of the projected pattern can be
adjusted.
G000-G255: This controls the positioning and any fixed setting of the Gobo wheel, within which a specific
pattern can be set. It is also possible to apply Gobo shake, adding an extra dimension and movement to the
projected effect.
SU00-99: This mode allows you to set the sensitivity of the in-built microphone. The further the device is
installed from the sound-source, the higher the sensitivity of the microphone needs to be so that the sound is
registered and the device responds accordingly and in time to the music. The microphone is able to
withstand high sound pressure. However, if the sound is loud and the sensitivity is high, the microphone will
find it more difficult to register the beat. Experiment with the sensitivity and distance from the positioning of
the device to make sure you’re getting the best possible signal and optimum performance.
The information in this user manual is subject to change at any time without notice.
Version: 1.0 Date of creation and author's initials: 07-10-2019 RV Revision date and author's initials: -

Operation Modes
Please find a clear explanation of the differences between all available Operation Modes below and how
they are affected by the menu functions listed above.
Auto:
In Auto Mode, you can select one of the Operation Modes in which the device is not dependent on external
factors such as sent signals, master signals or sound. The device can be set to this mode by entering the SP
function, setting it and then letting the device run it course.
Manual:
The manual mode gives you the option of adjusting all functions according to your own specifications. Here,
you can manually adjust and control rotation, dimmer, stroboscope etc.
Sound:
The sound-controlled mode or ‘sound mode’ uses an in-built microphone that registers the beat of music and
a runs a program based on this. For example, the device can move in virtual synchronisation with any music,
providing an automatic light-show.
hen no music is detected or only highs are present in the music due to a break, the device will continue its
program at a slower pace. As such, the light show does not appear to come to a stand still. As soon as
sound is registered by the microphone once more, the device shall continue its program in synchronisation
with the beat.
Slave
In Slave Mode, it is possible to connect several devices of the same type with one another so that they
perform exactly the same movements and functions at the same time. Therefore, single devices do not
respond individually (or chaotically) and this results in a completely coordinated show. In theory, by adding a
DMX booster, an unlimited number of Slave devices can be linked to one Master device. Initially, no problem
would occur if 4 devices were linked and no DMX booster were added.
Please note: If you link devices of a different type or brand (even if they appear to have the same function),
chaotic or strange behaviour can occur. This is often because certain functions are linked to the incorrect
channels. This applies to DMX lighting of all types and brands.
DMX
The DMX Mode is the most comprehensive mode for optimum control over all functions of this device. Via
DMX, it is possible to control either a limited or large amount of functions via a DMX controller or DMX
software.
The device can be set to different channel modes so the channel layout (included below) is in alignment with
the layout of your DMX circuit and with the functions you want to use.
4CH mode:
CH Function Value
1 Dimmer 0-100% 000-255
2 Strobe 000-007 No function
008-247 Stroboscope speed, slow to
fast
248-255 Automatic operation mode
3 Rotation 000-009 Stop
010-120 Clockwise rotation, fast to
slow
121-134 Stop
135-245 Anti-clockwise rotation, slow to
The information in this user manual is subject to change at any time without notice.
Version: 1.0 Date of creation and author's initials: 07-10-2019 RV Revision date and author's initials: -

fast
246-255 Stop
4 Gobo 000-063 Gobo selection
064-127 Gobo shake selection
128-189 Gobo wheel, clockwise
rotation, fast to slow
190-193 Stop
194-255 Gobo wheel, anti-clockwise
rotation, slow to fast
The information in this user manual is subject to change at any time without notice.
Version: 1.0 Date of creation and author's initials: 07-10-2019 RV Revision date and author's initials: -

Installation and Connection Instructions
Now you know how the TDC Acid works. So that the device is used in the correct and safest way, please
make sure to follow the installation and connection instructions.
Make sure that children do not have access to the device or any connecting cables. If there are children
present, make sure that they are supervised. Since the device can be placed upright or be suspended, it is
possible for children to pull on any connecting cables and cause the device to fall. To prevent any accidents
or injury, this must be taken into account whenever the device is being positioned and/or installed.
Upright use
hen you want to place the TDC Acid in an upright position, make sure that the device is placed on a stable
surface such as a table, DJ booth or bar. The double suspension bracket is designed so that it can function
as a stand. This way, the spotlight can be directed towards your audience or positioned to provide uplighting.
Always make sure that the light is positioned on a stable surface and that any cabling is secured so that no
one can trip and knock or pull the device over.
Suspended use (brackets)
Should you want to suspend the TDC Acid, use the suspension brackets, tightening knobs and rubber rings
included.
Place the rubber rings between the bracket and the fixture. Then tighten the knobs on both sides to make
sure that the bracket is secure.
If you want to suspend the device with a half-coupler or G-hook, this can be done by using the pre-drilled
holes in the bracket. Standard hooks and/or brackets for 35 or 50 mm tubes (trusses or light stands) are
available from your local retailer.
Hardware for mounting the TDC Acid to the wall, ceiling, or beam is not included. Contact a specialist if
you're not sure what hardware is required for your situation. A wooden beam and stone wall require different
mounting methods.
hen the TDC Acid is suspended, you will need to attach a safety cable to the fixture. This is not included
but is available at your local retailer. The device is fitted with an attachment point for hooking a safety cable.
Once hooked on, the cable can be wrapped around the truss or light stand and attached once more to the
same hook. This ensures the device is secure and prevents it from falling, even if one or both of the brackets
should come loose and fail.
Ensure that the safety cable has a load capacity of 10x the weight of the armature and that the device can
not fall farther than 30cm. You can wrap the safety cable around the truss or light stand several times to
ensure the fall is as short as possible. The shorter the fall, the less chance of damage or injury.
Light source
The TDC Acid uses powerful LED modules that are made even more powerful by a special lens that
combines and focuses these beams, much like a magnifying glass. Since the human eye cannot adjust
quickly enough to sudden and intense exposure to the level of brightness this device produces, never look
directly into the lens at close range. hile it won't result in permanent damage, it can cause temporary blind
spots which may cause disorientation and discomfort.
Cooling
The TDC Acid is cooled by fans fitted in the housing. These fan automatically switch on when the device is
switched on. Make sure the fans and vents are not blocked and regularly check that they are functioning
normally. Be aware that should the fans becomes clogged with substances like dust, smoke and moisture,
this may impair operation and shorten the life-span of the device.
The information in this user manual is subject to change at any time without notice.
Version: 1.0 Date of creation and author's initials: 07-10-2019 RV Revision date and author's initials: -

Parts and repairs
This product does not include spare parts and can not be repaired by the user. Any inspections and overall
maintenance should be carried out by a specialist only.
Cleaning and maintenance
Clean the exterior of this device on a monthly basis with a dry, or slightly damp microfibre cloth. Ensure that
the device is unplugged before cleaning it.
Check that all screws are intact and secured and tighten or replace them where needed. Check all metal
parts of the device for any signs of corrosion. If corrosion is found, the device needs to be checked
thoroughly.
Power Output
The TDC Acid is fitted with IEC C14 power input and an IEC C13 power output. This makes it possible to link
multiple devices with one single power supply, wall socket or power block.
The fuse fitted in this device is intended to protect that single device only. The input and output of the power
supply are directly wired to each other.
Since a standard 230 V group can handle a maximum load of 16A, and each TDC Acid consumes energy
itself, the output can only handle 9A worth of external devices. This also includes a calculated safety margin.
This is more than enough room to connect multiple LED light effects to each other without having to use
more than one power socket. Avoid connecting high-power equipment such as powerful smoke machines
and high-output halogen lighting.
DMX terminator
hen using the device in DMX mode, it is common for a ‘terminator’ to be used at the end of the DMX
circuit. A DMX terminator is a terminal resistor, consisting of a 120 Ohm resistor placed between the second
and third pins to eliminate any data reflections. Data reflections can cause strange behaviour in DMX
controlled devices.
DMX-terminators are sold read-made but it is possible to solder a 120 Ohm resistor between the second and
third pins of a standard, male XLR connector.
The information in this user manual is subject to change at any time without notice.
Version: 1.0 Date of creation and author's initials: 07-10-2019 RV Revision date and author's initials: -

DMX Lighting Troubleshooting
If you have a problem with your DMX light effect, please consult the troubleshooting section for possible
solutions. If, after consulting this section, the problem remains unresolved, please contact your retailer for
more information and/or help.
This troubleshooting section contains information on how to solve the most common DMX light effect
problems, but it does not and cannot cover every eventuality.
Problem Possible Cause Solution
The device can not be turned on The fuse is blown Check the fuse to rule out if it is
blown or not. If it is blown, replace
it with a new fuse of the same type
and class.
Power cable not plugged in Check if the power cable is
properly connected to the device
and plugged into an active power
socket.
The device is not reacting to DMX
signals
Incorrect DMX start address Check if the device has been set
to the correct DMX start address
DMX controller is set to ‘Blackout’ Make sure the ‘Blackout’ function
on the DMX controller is not
activated
Make sure the polarity switch on
the DMX controller is set correctly
Try to reverse the DMX polarity
switch on the DMX controller.
The device is not reacting, there is
no DMX signal indication
Make sure the XLR cables are
connected properly and are not
defective. Replace if necessary.
The device does not react to
sound/music
Incorrect operation mode Make sure the sound-activated
mode has been selected.
The internal microphone sensitivity
is too low
Check the microphone sensitivity
level and increase it if necessary.
The speaker is too far away, or is
not producing enough low tones
Place the light effect closer to a
speaker (or vice versa) and/or
increase the low-frequency level.
The built-in microphone is not
triggered by high tones.
The amount of projected light is
minimal
Dirty or dusty optics Clean the lens and/or other optics.
Dimmer is not completely open Check if the dimmers on the
spotlights themselves and/or if the
master dimmer is completely open.
Also, check the colour balance
settings.
The DMX signal appears to be
interrupted and some devices are
flashing or behaving strangely
Damaged/defective cables Check and replace the DMX
cables if necessary.
Power interference on the DMX
signal
Avoid connecting signal cables
parallel to power cables.
DMX terminator missing Close the DMX circuit with a DMX
terminator
The information in this user manual is subject to change at any time without notice.
Version: 1.0 Date of creation and author's initials: 07-10-2019 RV Revision date and author's initials: -

Signal loss or interference in the
DMX circuit
Close the DMX circuit with a
terminator or connect a booster
after maximum 32 fixtures.
The device is not reacting properly
to DMX commands
Incorrect DMX channel mode Check that the correct DMX
channel mode is set
The operation mode can not be
changed
The device is in Slave mode If the device is in Slave mode, it
will wait for a master signal unless
there is a DMX signal present. Set
the device to Master to activate the
sound-controlled or automated
operation modes.
The information in this user manual is subject to change at any time without notice.
Version: 1.0 Date of creation and author's initials: 07-10-2019 RV Revision date and author's initials: -

Technical Specifications
Specifications:
- Kaleidoscopic light effect
- Rotating effects thanks to a Gobo wheel and prisma
- Powerful 100 att white LED light source
- Diverse operation modes for stand-alone (static or programmes) as controlled use (sound-controlled,
automatic, Master / Slave, DMX)
- DMX controlled via 4 DMX channels
- DMX connection via 3-pin XLR inputs and outputs
- LED Display with Menu buttons
- Integrated microphone for sound/music-controlled mode
- Adjustable microphone sensitivity
- Light output: 10125 Lux at 1m
- Beam angle: 40 Degrees
- Power supply: 100-240V AC, 50/60 Hz
- Power factor: 0.708 at 110V, 0.621 at 220V
- Nominal temperature: Between 0°C and 40°C
- Maximum temperature of housing when in normal use: 50°C
- Maximum power consumption: 110
- Fuse: F3AL250V
- Dimensions: 230 x 280 x 145 mm
- eight: 4.15 kg
The information in this user manual is subject to change at any time without notice.
Version: 1.0 Date of creation and author's initials: 07-10-2019 RV Revision date and author's initials: -