Moxa Technologies ioThinx 4510 Series User manual

P/N: 1802045101010
*1802045101010*
ioThinx 4510 Series
Quick Installation Guide
Edition 1.0, August 2018
Technical Support Contact Information
www.moxa.com/support
Moxa Americas:
Toll
-free: 1-888-669-2872
Tel:
1-714-528-6777
Fax:
1-714-528-6778
Moxa China (Shanghai office):
Toll
-free: 800-820-5036
Tel:
[phone]
Fax:
[phone]
Moxa Europe:
Tel:
[phone]
Fax:
[phone]
Moxa Asia-Pacific:
Tel:
[phone]
Fax:
[phone]
Moxa India:
Tel:
[phone]
Fax:
[phone]

2018 Moxa Inc. All rights reserved.

- 2 -
Introduction
The ioThinx 4510 is an advanced modular remote I/O device with a
unique hardware and software design that makes it ideal for a variety
of industrial data acquisition applications.
Package Checklist
•1 ioThinx 4510 product
•Quick installation guide (printed)
•2 side cover plates
Installation
Connecting System Power
Connect your 12 to 48 VDC power source to the terminal block SP+ and
SP- terminals on the ioThinx 4510. The ground connector of the system
is on the back of the unit, which will connect to the DIN-rail when the
product is attached to it.

- 3 -
Connecting Field Power
The ioThinx 4510 can receive field power
through a 12/
24 VDC power input. Field
power can be used to supply power for
some I/O modules, such as digital input
and analog output modules.
Connecting the Field Power Ground
Connect the
Field Ground pin (
) to the
field power
ground.
Connecting to the Network
Ethernet Communication
The ioThinx 4510 is equipped with dual unmanaged LAN ports (RJ45).
Connect a network Ethernet cable to either port to provide an Ethernet
connection to the unit.

- 4 -
Serial Communication
The ioThinx 4510 is equipped with a 3-in-1 serial interface, which
supports 1 RS-232 port, or 1 RS-422 port, or 2 RS-485 ports. Follow
the pin assignment table below to set up serial connection to the unit.
PIN
RS-232
(P1)
RS-422
(P1)
RS-485
(P1/P2)
1
TXD
TXD+
DATA 1+
2
RXD
TXD-
DATA 1-
3
RTS
RXD+
DATA 2+
4
CTS
RXD-
DATA 2-
5
GND
GND
GND
45M Module Wiring
For detailed 45M module wiring, refer to the ioThinx 4510 User Manual
on the official website.
Installing the System on a DIN-Rail
Step 1: Hook the mounting clip of the unit onto the DIN-rail and lower
the clip onto the DIN-rail. Reserve at least 5.5 cm of space above the
DIN-rail to ensure that there is enough room to install the unit.
Step 2: Push the unit toward the
DIN
-rail until the mounting clip
snaps in place.

- 5 -
Installing a 45M Module on a DIN-Rail
Step 1: Align the 45M module side by side
with the head/CPU module, making sure that
the upper and lower rails are hooked
together.
Step 2: Align the 45M module side by side with the head/CPU module
and then push the 45M module until it touches the DIN-rail. Next, apply
more force until the module clips to the DIN-rail.
NOTE
After the module is firmly attached to the DIN-rail, the module
connections to the internal bus will be established.
Removing a 45M Module from a DIN-Rail
Step 1: Use your finger to lift the
release tab on the lower part of the
module.

- 6 -
Step 2: Push the top of the release tab to latch it, and then pull the
module out.
NOTE
Electrical connections for internal bus will be disconnected when
removing the 45M module.
WARNING
Be sure the power is off before removing modules to avoid
unexpected damage.
Installing the Covers on the First and Last Module
Attach the covers to the first and last module to cover the modules’
contacts.
NOTICE
Be sure to attach the covers to provide electrostatic discharge
protection.

- 7 -
LED Indicators
Name
Indication
LED Qty
Description
SP System
Power
1 On: Power on
Off: Power off
FP
Field Power
1
On: Power on
Off: Power off
RDY
System
(Kernel)
Ready
1
Green: System ready
Green Slow Blinking: Booting up
Red: System error
Red Slow Blinking: Loading Factory
Default Recovery/Upgrading
firmware/Backup mode
Red Fast Blinking: Safe mode
Off: Power off
LAN
Ethernet
Connection
1 for
each port
Green: 100Mb connection
Amber: 10Mb connection
Blinking: Data transmitting
Off: Disconnected
Px
Serial
Connection
1 for
each port
Green: Tx
Amber: Rx
Non-simultaneous Blinking: Data
transmitting
Off: Disconnected
System Configuration
1. Configuration via Web Console
Main configuration of the unit is done through the web console.
•Default IP Address: 192.168.127.254
•Subnet Mask: 255.255.255.0
NOTE
Be sure to configure the host PC’s IP address to use the same
subnet as the unit. For example, 192.168.127.253
2. IOxpress Utility
IOxpress is a utility that helps users with mass deployment of,
searching for, and locating units on the local network. This utility
can be downloaded from Moxa’s website.
3. Loading the Factory Default Settings
There are three ways to restore the unit to the factory default
settings:
I. Hold the Reset button inside the front door of the unit for 10
seconds while it is powered on.
II. In the IOxpress utility’s Device Library page, select the unit and
choose Load Factory Default.
III. Go to the System tab on the unit’s web console and choose
Load Factory Default in the Configuration section.
NOTE
Please refer to the user's manual for information on detailed
configuration and settings.

- 8 -
How to Download the Software
Related software packages can be downloaded from the Moxa website.
Step 1: Go to the following address to open the Support & Downloads
search tool:
http://www.moxa.com/support/support_home.aspx?isSearchShow=1
Step 2: Type the model name in the search box or select a product
from the drop-down box and then click Search. The ioLogik E1210 is
used for the examples below.
Step 3: Go to the Software page to download the latest software for
the product.
Specifications
Input Current
800 mA @ 12 VDC
Input Voltage
12 to 48 VDC
Field Power: 12/24 VDC
Operating Temperature
Standard Models:
-20 to 60°C (-4 to 140°F)
Wide Temp. Models:
-40 to 75°C (-40 to 167°F)
Storage Temperature
-40 to 85°C (-40 to 185°F)