Moxa Technologies ioLogik E2260 User manual

ioLogik E2260 User’s Manual
Fourth Edition, June 2009
www.moxa.com/product
©2009 Moxa Inc. All rights reserved.
Reproduction without permission is prohibited.

ioLogik E2260 User’s Manual
The software described in this manual is furnished under a license agreement, and may be used only in
accordance with the terms of that agreement.
Copyright Notice
Copyright ©2009 Moxa Inc.
All rights reserved.
Reproduction without permission is prohibited.
Trademarks
MOXA is a registered trademark of Moxa Inc.
All other trademarks or registered marks in this manual belong to their respective manufacturers.
Disclaimer
Information in this document is subject to change without notice, and does not represent a commitment on the
part of Moxa.
Moxa provides this document “as is,” without warranty of any kind, either expressed or implied, including, but
not limited to, its particular purpose. Moxa reserves the right to make improvements, and/or changes to this
manual, or to the products, and/or the programs described in this manual, at any time.
Information provided in this manual is intended to be accurate, and reliable. However, Moxa assumes no
responsibility for its use, or for any infringements on the rights of third parties that may result from its use.
This manual might include unintentional technical or typographical errors. Changes are made periodically to the
information herein to correct such errors, and these changes are incorporated into new editions of the manual.
Technical Support Contact Information
www.moxa.com/support
Moxa Americas:
Toll-free: 1-888-669-2872
Tel: [phone]
Fax: [phone]
Moxa China (Shanghai office):
Toll-free: 800-820-5036
Tel: [phone]
Fax: [phone]
Moxa Europe:
Tel: [phone]
Fax: [phone]
Moxa Asia-Pacific:
Tel: [phone]
Fax: [phone]

Table of Contents
Chapter 1. Introduction ...............................................................................................1-1
Overview.............................................................................................................................. 1-2
Traditional Remote I/O................................................................................................. 1-2
Active Ethernet I/O....................................................................................................... 1-2
Click&Go ..................................................................................................................... 1-3
Optional Liquid Crystal Display Module (LCM)......................................................... 1-3
Product Features................................................................................................................... 1-3
Packing List.......................................................................................................................... 1-3
Product Specifications..........................................................................................................1-4
Physical Dimensions ............................................................................................................ 1-6
With LCD Module........................................................................................................ 1-6
Without LCD Module................................................................................................... 1-7
Hardware Reference............................................................................................................. 1-7
Panel Guide .................................................................................................................. 1-7
LED Indicators ............................................................................................................. 1-8
Chapter 2. Initial Setup................................................................................................2-1
Hardware Installation ...........................................................................................................2-2
Connecting the Power................................................................................................... 2-2
Grounding the ioLogik E2260...................................................................................... 2-2
Connecting to the Network........................................................................................... 2-2
Setting the RS-485 Baudrate ........................................................................................ 2-2
Adding More I/O Channels .......................................................................................... 2-3
Software Installation............................................................................................................. 2-3
Chapter 3. Utilities .......................................................................................................3-1
Introduction to ioAdmin....................................................................................................... 3-2
Features of ioAdmin.............................................................................................................3-2
ioAdmin Main Screen........................................................................................................... 3-4
Main Screen Overview................................................................................................. 3-4
Wiring Guide................................................................................................................ 3-5
Menu Items........................................................................................................................... 3-5
File................................................................................................................................ 3-5
System ..........................................................................................................................3-6
Sort ............................................................................................................................... 3-7
Help .............................................................................................................................. 3-7
Quick Links .................................................................................................................. 3-7
Main Window....................................................................................................................... 3-8
I/O Configuration Tab (General).................................................................................. 3-8
Server Info Tab............................................................................................................. 3-8
Server Settings Tab (General) ...................................................................................... 3-9
Message Monitor Tab................................................................................................... 3-9
ioAdmin Administrator Functions...................................................................................... 3-10
I/O Configuration Tab (Administrator) ...................................................................... 3-10
Server Settings Tab (Administrator)........................................................................... 3-13
Network Tab............................................................................................................... 3-15
Firmware Update Tab................................................................................................. 3-17
Watchdog Tab............................................................................................................. 3-17
Click&Go Logic Tab.................................................................................................. 3-18

Active Tags Tab.......................................................................................................... 3-19
SNMP Settings Tab .................................................................................................... 3-20
Server Context Menu.................................................................................................. 3-20
Using TFTP to Import/Export Configuration ..................................................................... 3-22
Using ioEventLog............................................................................................................... 3-23
Installing ioEventLog ................................................................................................. 3-23
Basic Functions........................................................................................................... 3-23
Configuration.............................................................................................................. 3-24
Checking Connected Devices..................................................................................... 3-25
Opening Log Files...................................................................................................... 3-25
Clearing the Log......................................................................................................... 3-26
Chapter 4. Using the Web Console ............................................................................4-1
Introduction to the Web Console.......................................................................................... 4-2
Basic Settings ....................................................................................................................... 4-2
Network Settings.................................................................................................................. 4-3
General Settings............................................................................................................ 4-3
Ethernet Configuration ................................................................................................. 4-3
RS-485 Settings............................................................................................................ 4-4
I/O Settings........................................................................................................................... 4-4
RTD Channels .............................................................................................................. 4-4
DO Channels ................................................................................................................ 4-5
System Management ............................................................................................................ 4-6
Accessible IP Settings................................................................................................... 4-6
SNMP Agent ................................................................................................................ 4-7
Network Connection..................................................................................................... 4-7
Firmware Update.......................................................................................................... 4-8
Import System Config .................................................................................................. 4-8
Export System Config .................................................................................................. 4-8
LCM ..................................................................................................................................... 4-9
Change Password.................................................................................................................. 4-9
Load Factory Default............................................................................................................4-9
Save/Restart.......................................................................................................................... 4-9
Chapter 5. Active OPC Server Lite .............................................................................5-1
Overview.............................................................................................................................. 5-2
Introduction to Active OPC Server Lite ............................................................................... 5-2
Active OPC Server Lite – From Pull to Push....................................................................... 5-3
Features of Active OPC Server Lite ..................................................................................... 5-4
Active OPC Server Lite Specifications ................................................................................ 5-5
Installation of Active OPC Server Lite......................................................................... 5-5
Installation of OPC Core Components ......................................................................... 5-5
Active OPC Server Lite........................................................................................................ 5-6
Main Screen Overview................................................................................................. 5-6
Menu Items........................................................................................................................... 5-7
File................................................................................................................................ 5-7
System ..........................................................................................................................5-7
Sort ............................................................................................................................... 5-8
Quick Links .................................................................................................................. 5-8
Tag Generation ..................................................................................................................... 5-9
Push Tag Configuration from ioAdmin........................................................................ 5-9
Advanced Settings...................................................................................................... 5-11

Heartbeat Interval....................................................................................................... 5-11
Read/Write Privilege .................................................................................................. 5-12
OPC Test Client.......................................................................................................... 5-12
Appendix A. Liquid Crystal Display Module (LCM).....................................................A-1
Appendix B. Modbus/TCP Address Mappings ............................................................B-1
0xxxx Read/Write Coils (Functions 1, 5, 15) .......................................................................B-1
3xxxx Read Only Registers (Function 4) .............................................................................B-2
4xxxx Read/Write Registers (Functions 3, 6, 16).................................................................B-3
Appendix C. Used Network Port Numbers...................................................................C-1
Appendix D. SNMP MIB II ..............................................................................................D-1
RFC1213 MIB II Supported SNMP Variables..................................................................... D-1
Private MIB File and SNMP Variables................................................................................ D-4
Appendix E. CGI Commands ........................................................................................ E-1
Appendix F. Factory Default Settings...........................................................................F-1
Appendix G. Pinouts and Cable Wiring........................................................................G-1
Ethernet Port Pinouts...........................................................................................................G-1
Serial Port Pinouts............................................................................................................... G-1
RTD Input Wiring................................................................................................................G-1
Structure ...................................................................................................................... G-1
2-wire........................................................................................................................... G-2
3-wire........................................................................................................................... G-2
Digital Output...................................................................................................................... G-2
Structure ...................................................................................................................... G-2
Output Channel............................................................................................................ G-3
Terminal Block Pin Assignments......................................................................................... G-3
Appendix H. Accuracy...................................................................................................H-1
Calibration........................................................................................................................... H-1
Simple Verification at Your Site .......................................................................................... H-1
Verification with RTD Sensor..................................................................................... H-1
Verification with Precision Resistor............................................................................ H-1

1
1
Chapter 1. Introduction
The ioLogik E2260 is a stand-alone Active Ethernet I/O server. It connects RTD sensors and
digital output on/off switches for automation applications over Ethernet and IP-based networks.
The following topics are covered in this chapter:
Overview
Traditional Remote I/O
Active Ethernet I/O
Click&Go
Optional Liquid Crystal Display Module (LCM)
Product Features
Packing List
Product Specifications
Physical Dimensions
With LCD Module
Without LCD Module
Hardware Reference
Panel Guide
LED Indicators

ioLogik E2260 User’s Manual Introduction
1-2
Overview
(shown with and without optional LCM)
The ioLogik E2260 is part of the E2000 line of ioLogik Active Ethernet I/O servers, which are
designed for intelligent, pro-active status reporting of attached sensors, transmitters, transducers,
and valves over a network. It includes 2 MB of Flash ROM and 8 MB of SDRAM. An optional
hot-pluggable Liquid Crystal Display Module (LCM) can be used to view and configure device
settings.
Traditional Remote I/O
Ethernet remote I/O solutions have been on the market for a long time. Traditional solutions are
“passive,” in the sense that I/O servers wait passively to be polled by a host computer. The
response time in this type of setup, however, tends to be on the order of seconds. The “passive”
remote I/O structure is simply inadequate for data acquisition and control systems that require a
response time on the order of hundredths of seconds.
Active Ethernet I/O
Moxa’s Active Ethernet I/O line was developed specifically to address the limitations of the
traditional passive approach. Rather than having the host computer poll the I/O device server over
the network for the status of each I/O device, the Active Ethernet I/O server intelligently sends the
host computer status information under user-specified conditions. This is a report by exception
approach, which greatly reduces the load on CPU and network resources. Network packets are far
fewer in number and far smaller in size, since I/O information is only sent when necessary, and
only information from the specified I/O device is sent. Based on field tests of an ioLogik E2000
series server used in an RFID system, 50 ms is the typical response time over a 100 Mbps Ethernet
network. Moxa’s active I/O messaging system uses TCP or UDP for I/O messaging and supports
sending messages to up to ten host computers simultaneously.
In addition to providing intelligent status reporting, Active Ethernet I/O servers are backwards
compatible, with all of the functions and capabilities of traditional passive remote I/O servers.

ioLogik E2260 User’s Manual Introduction
1-3
Click&Go
Moxa developed the Click&Go Logic control interface for easy configuration and deployment of
Active Ethernet I/O. Click&Go’s intuitive, graphical interface lets administrators use simple
IF/THEN statements as rules to determine how the Active Ethernet I/O server responds to different
I/O conditions. For example, the Active Ethernet I/O server could be programmed so that if the
temperature recorded by an attached sensor reaches a certain value, an attached switch is turned on
and an e-mail is sent to an administrator. Click&Go makes it easy to define a set of these rules,
which will become the basis for your Active Ethernet I/O system.
Optional Liquid Crystal Display Module (LCM)
In order to make user easy view, the ioLogik E2260 supports an optional hot-pluggable Liquid
Crystal Display Module (LCM) for field management and configuration. The LCM can display
network and I/O settings such as temperature value. The ioLogik E2260’s IP address and netmask
may also be configured using the LCM, and one LCM can be used to maintain and configure all
ioLogik 2000 devices.
Product Features
yClick&Go Logic for easy configuration of your Active Ethernet I/O system
yHigh-speed active I/O messaging
y6 input channels for 2-wire or 3-wire resistance temperature devices (RTD) such as PT100,
JPT100, and more, with software selectable filtering time
y4 channels for 24 VDC output with Pulse Output mode and software selectable pulse width
y10/100 Mbps Ethernet supporting Modbus/TCP and up to 10 hosts
yWindows utility and quick programming library for VB, VC++, BCB (coming soon)
yExpandable I/O through optional RS-485 modules
ySupports SCADA software including Wonderware InTouch and GE Intellution iFix32
ySNMP for system management and I/O status
yRemote management over the network including firmware updates
ySupports TFTP server to import configuration
yPower-on and safe status settings for digital output
yOptional hot-pluggable LCM for status display and configuration
Packing List
The ioLogik E2260 is shipped with the following items:
Standard Accessories
yioLogik E2260 Active Ethernet I/O server
yDocument and Software CD
Optional Accessories
yLDP1602 ioLogik liquid crystal display module (LCM)
NOTE: Notify your sales representative if any of the above items are missing or damaged.

ioLogik E2260 User’s Manual Introduction
1-4
Product Specifications
LAN
Ethernet 10/100 Mbps, RJ45
Protection 1.5 KV magnetic isolation
Protocols Modbus/TCP, TCP/IP, UDP, DHCP, Bootp, SNMP(MIB for I/O
and Network), HTTP
Serial
Interface RS-485 (2-wire): Data+, Data-, GND
Serial Line Protection 15 KV ESD for all signals
Serial Communication Parameters
Parity None
Data Bits 8
Stop Bits 1
Flow Control None
Speed 1200 to 115200 bps
Protocol Modbus/RTU
Built-in RTC Yes
RTD Input
Channels 6, resistance temperature devices
I/O Mode PT, JPT, Ni, resistor with burn-out detection
Input Impedance 5 M(typical), 625 K(min.)
Input Connection 2 or 3 wire
Resolution 16 bits
Sample Rate 12 samples/sec (all channels)
Accuracy +/-0.1%
Zero Drift +/- 3 uV/C (typical)
Span Drift +/- 25 ppm/C
CMR @50/60Hz 120 dB
NMR @50/60Hz 100 dB
Optical Isolation 2 KVrms / 3 KVDC
Supported RTD Types Sensor Type Degree Degree Count
Res. 100 m1 to 2200 1 to 2200 10 to 22000
Res. 50 m1 to 1250 1 to 1250 20 to 25000
Res. 20 m1 to 620 1 to 620 50 to 31000
Res. 10 m1 to 310 1 to 310 100 to 31000
PT50, 0.00385 -200 to 850°C -328 to 1562°F -2000 to 8500
PT100, 0.00385 -200 to 850°C -328 to 1562°F -2000 to 8500
PT200, 0.00385 -200 to 850°C -328 to 1562°F -2000 to 8500
PT500, 0.00385 -200 to 850°C -328 to 1562°F -2000 to 8500
PT1000, 0.00385 -200 to 350°C -328 to 662°F -2000 to 3500
JPT100, 0.003916 -200 to 640°C -328 to 1184°F -2000 to 6400
JPT200, 0.003916 -200 to 640°C -328 to 1184°F -2000 to 6400
JPT500, 0.003916 -200 to 640°C -328 to 1184°F -2000 to 6400
JPT1000, 0.003916 -200 to 350°C -328 to 662°F -2000 to 3500
Ni100, 0.00618 -60 to 250°C -76 to 482°F -600 to 2500
Ni200, 0.00618 -60 to 250°C -76 to 482°F -600 to 2500
Ni500, 0.00618 -60 to 250°C -76 to 482°F -600 to 2500
Ni1000, 0.00618 -60 to 180°C -76 to 356°F -600 to 1800
Ni120, 0.00672 -80 to 260°C -112 to 500°F -800 to 2600

ioLogik E2260 User’s Manual Introduction
1-5
Virtual RTD
Channels 6
Operation Mode Average, Subtraction
Digital Output
Channels 4, sink type
On-state Voltage 24 VDC nominal, 30 VDC max.
Output Current Rating Max. 200 mA per channel
Optical Isolation 2 KVrms/3 KVDC
Protection Over temperature shutdown: 170°C
Over current limit: 750 mA/channel (typical)
Power Requirements
Power Input 24 VDC nominal, 12 to 48 VDC (max.)
Power Consumption 2.16 W @ 24 VDC (typical)
3.54 W with LCM (max.)
Field Power 24 VDC nominal, up to 48 VDC
Mechanical Specifications
Wiring I/O cable max. 14AWG
Environmental
Operating Temperature -10 to 60ºC (14 to 140ºF), 5 to 95%RH
Storage Temperature -40 to 85ºC (-4 to 185ºF), 5 to 95%RH
Shock IEC60068-2-27
Freefall IEC60068-2-32
Vibration IEC60068-2-6
MTBF > 200,000 hrs @ 25°C
AgencyApprovals
EMC FCC Part 15, CISPR (EN55022) Class A
CE-IEC61000-4-2 (ESD), Level 2/3
CE-IEC61000-4-3 (RS), Level 2
CE-IEC61000-4-4 (EFT), Level 2
CE-IEC61000-4-5 (Surge), Level 3
CE-IEC61000-4-6 (CS), Level 2
CE-IEC61000-4-8 (PM), Level 1
CE-IEC61000-4-11 (Dip)
CE-EN61000-6-2
CE-EN61000-6-4
Safety UL 508
Warranty
Period 2 years

ioLogik E2260 User’s Manual Introduction
1-6
Physical Dimensions
With LCD Module
Unit = mm
5.95 5.95
646.51
93.02
115
121.8
44.5 35.1
57.5
10.98
9.5
6.89
3.39
79
3.4
79 39.5
9.51
45.63
10.7

ioLogik E2260 User’s Manual Introduction
1-7
Without LCD Module
45.39
10.7
5.95 24.44
Unit = mm
6
46.51
93.02
115
121.8
10.98
9.5 79 39.5
9.51
Hardware Reference
Panel Guide
NOTE: The reset button restarts the server and resets all settings to factory defaults. Use a pointed
object such as a straightened paper clip to hold the reset button down for 15 sec. The RDY LED
will turn red as you are holding the reset button down. The factory defaults will be loaded once the
RDY LED turns green again. You may then release the reset button.
(TB2)
(TB1)

ioLogik E2260 User’s Manual Introduction
1-8
LED Indicators
Ethernet orange Valid 10 Mbps Ethernet connection
green Valid 100 Mbps Ethernet connection
Ethernet (flashing) Transmitting or receiving data
System red Power is on
PWR off Power is off
red System error
green (steady) Unit is functioning normally
green (flashing) Click&Go ruleset is active
green & red (flashing) Safe status settings activated
RDY
off Power is off or there is a power problem.
Serial (flashing) Serial port is receiving/transmitting data
RTD green Normal operation
red Channel error or no connection
RTD × 6 pins off Channel off
Digital Output green ON status
DO × 4 pins off OFF status
red ON status
DO PWR off No power in

2
2
Chapter 2. Initial Setup
This chapter describes how to install the ioLogik E2260.
The following topics are covered:
Hardware Installation
Connecting the Power
Grounding the ioLogik E2260
Connecting to the Network
Setting the RS-485 Baudrate
Adding More I/O Channels
Software Installation

ioLogik E2260 User’s Manual Initial Setup
2-2
Hardware Installation
Connecting the Power
Connect the 12 to 48 VDC power line to the ioLogik E2260’s terminal block (TB1). If power is
properly supplied, the Power LED will glow a solid red color until the system is ready
ATTENTION
Disconnect the power before installing and wiring
Disconnect the power cord before installing and/or wiring your ioLogik E2260.
Do not exceed the maximum current for the wiring
Determine the maximum possible current for each power wire and common wire. Observe all
electrical codes dictating the maximum current allowable for each wire size.
If the current exceeds the maximum rating, the wiring could overheat, causing serious damage to
your equipment.
Grounding the ioLogik E2260
There are two grounding points on the ioLogik E2260: the wall mounting point and the DIN-rail
mounting plate. Note that both grounding points are actually connected to the same conducting
pathway.
Connecting to the Network
1. Connect the ioLogik E2260 to the host PC with an Ethernet cable. For initial setup of the
ioLogik E2260, it is recommended that the ioLogik E2260 be configured using a direct
connection to a host computer rather than remotely over the network.
2. Note the ioLogik’s default IP settings:
IPAddress Netmask Gateway
192.168.127.254 255.255.255.0 None
Configure the host PC’s IP address to 192.168.127.xxx. (xxx: from 001 to 253) so the ioLogik
will be visible on the network. In Windows, you will need to do this through the Control Panel.
3. Use ioAdmin or the web console to detect the ioLogik E2260. Once the ioLogik E2260 has been
detected, modify the settings as needed for your network environment, then restart the ioLogik
E2260. For information on ioAdmin, please refer to Software Installation later in this chapter.
Setting the RS-485 Baudrate
The RS-485 port on the ioLogik E2260 is reserved for connecting to another RS-485 I/O server.
The RS-485 port can run Modbus/RTU or I/O command sets. The baudrate is set by a physical dial
on the back of the ioLogik E2260. The default settings are baudrate = 115200, parity check = N,
data bits = 8, and stop bit = 1.
Baudrate for RS-485
(parameters are N, 8, 1) Dial setting and corresponding baudrate: 0:115200 1:57600 2:38400 3:19200
4:9600 5:4800 6:2400 7:1200
Remember to restart the ioLogik E2260 after making any changes to the RS-485 baudrate.

ioLogik E2260 User’s Manual Initial Setup
2-3
Adding More I/O Channels
A cost effective way to add more I/O channels to your ioLogik E2000 I/O server is to attach the
appropriate ioLogik R2000 I/O server. The two servers can be snapped together using the RS-485
system bus connector, as shown in the following figure. Digital I/O channels can be added using
the ioLogik R2110, and analog I/O channels can be added using the ioLogik E2140. For additional
details, please refer to the ioLogik R2110 or R2140 user’s manual.
Software Installation
ioAdmin is a Windows utility provided for the configuration and management of the ioLogik
E2260 and attached I/O devices. It may be used from anywhere on the network to monitor and
configure the ioLogik E2260. You may also configure some of the settings through the web
console or optional LCM.
1. Installation from CD: Insert the Document and Software CDinto the host computer. In the root
directory of the CD, locate and run SETUP.EXE. The installation program will guide you
through the installation process and install the ioAdmin utility. You can also install the MXIO
DLL library or ioEventLog separately.
2. Open ioAdmin: After installation is finished, run ioAdmin from Start ÆProgram Files Æ
MoxaÆIO Server ÆUtility ÆioAdmin.
3. Search the network for the server: On the menu bar, select System ÆAuto ScanActive
Ethernet I/O Server.In the dialog window that appears, click Start Search to begin searching
for the ioLogik E2260.

ioLogik E2260 User’s Manual Initial Setup
2-4
If ioAdmin is unable to find the ioLogik E2260, there may be a problem with your network
settings.
When multiple ioLogik E2000 units are on the same network, remember that each unit has
the same default IP address. You will need to assign a different IP address to each unit to
avoid IP conflicts. ioAdmin automatically detects IP conflicts and gives you a chance to
modify each unit’s IP address in the “IP Address” columns. Click the “Set” button to reboot
the corresponding unit with its new IP address. Click the “Re-Search” button to refresh the
list of units found by ioAdmin.
4. Monitoring I/O status: Once the ioLogik E2260 is found by ioAdmin, you may view the status
of all I/O devices on ioAdmin’s main screen.
You may now use ioAdmin to set up or configure your ioLogik E2260.

3
3
Chapter 3. Utilities
This chapter goes over the functions available in ioAdmin, the ioLogik E2260’s main
configuration and management utility.
The following topics are covered:
Introduction to ioAdmin
Features of ioAdmin
ioAdmin Main Screen
Main Screen Overview
Wiring Guide
Menu Items
File
System
Sort
Help
Quick Links
Main Window
I/O Configuration Tab (General)
Server Info Tab
Server Settings Tab (General)
Message Monitor Tab
ioAdminAdministrator Functions
I/O Configuration Tab (Administrator)
Server Settings Tab (Administrator)
Network Tab
Firmware Update Tab
Watchdog Tab
Click&Go Logic Tab
Server Context Menu
Using TFTPto Import/Export Configuration
Using ioEventLog

ioLogik E2260 User’s Manual Utilities
3-2
Introduction to ioAdmin
The ioLogik I/O server may be managed and configured over the Ethernet by ioAdmin, a
Windows utility provided with your ioLogik E2260. ioAdmin’s graphical user interface gives you
easy access to all status information and settings.
The ioLogik E2260 also supports configuration by web console and by optional LCM, but full
configuration and management is only available through ioAdmin.
A new feature in ioAdmin automatically detects IP conflicts between ioLogik E2000 units. If
ioAdmin detects an IP conflict, a window will appear that allows you to resolve the IP conflict
immediately and restart each unit.
ioAdmin also includes Click&Go Logic control for the configuration of your Active Ethernet I/O
system.
ioAdmin consists of following software:
yioAdmin with Click&Go Logic
yioLogik 2000 Wiring Guide
yioLogik 4000 Wiring Guide
Features of ioAdmin
Remote Management
Over the Ethernet network, ioAdmin
allows users to
zfind and configure multiple
ioLogik servers
zmonitor and configure attached I/O
devices
ztest I/O devices
zreset the server
On-line Wiring Guide
An on-line wiring guide can be opened
from within ioAdmin for your
convenience. The easily accessible
wiring guide can save administrators
much time while planning or
troubleshooting.

ioLogik E2260 User’s Manual Utilities
3-3
Configuration File
ioAdmin allows the entire
configuration of the ioLogik E2260 to
be saved as a file. The file is viewable
as text and can serve three purposes:
zas a record or backup of
configuration
zas a template for the configuration
of other servers
zas a quick reference guide for you
to configure Modbus drivers in a
SCADA system
The file includes the following
information:
1. file name, date, and time
2. model information
3. Modbus addresses
Server Management List
ioAdmin can import and export a list
of ioLogik servers that are being
managed. This file can make it easier
to manage all devices on the network,
and includes the following
information:
1. Server Name
2. Module Type
3. IPAddress
4. Unit ID