Moxa Technologies ioLogik E1211 User manual

ioLogik E1200 Series User’s Manual
Edition 15.4, October 2018
www.moxa.com/product
© 2018 Moxa Inc. All rights reserved.

ioLogik E1200 Series User’s Manual
The software described in this manual is furnished under a license agreement and may be used only in accordance with
the terms of that agreement.
Copyright Notice
© 2018 Moxa Inc. All rights reserved.
Trademarks
The MOXA logo is a registered trademark of Moxa Inc.
All other trademarks or registered marks in this manual belong to their respective manufacturers.
Disclaimer
Information in this document is subject to change without notice and does not represent a commitment on the part of
Moxa.
Moxa provides this document as is, without warranty of any kind, either expressed or implied, including, but not limited
to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this manual, or to the
products and/or the programs described in this manual, at any time.
Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no responsibility for
its use, or for any infringements on the rights of third parties that may result from its use.
This product might include unintentional technical or typographical errors. Changes are periodically made to the
information herein to correct such errors, and these changes are incorporated into new editions of the publication.
Technical Support Contact Information
www.moxa.com/support
Moxa Americas
Toll
-free: 1-888-669-2872
Tel:
[phone]
Fax:
[phone]
Moxa China (Shanghai office)
Toll
-free: 800-820-5036
Tel:
[phone]
Fax:
[phone]
Moxa Europe
Tel:
[phone]
Fax: [phone]
Mo
xa Asia-Pacific
Tel:
[phone]
Fax: [phone]
Moxa India
Tel:
[phone]
Fax:
[phone]

Table of Contents
1. Introduction...................................................................................................................................... 1-1
Product Features ................................................................................................................................ 1-2
Inside the Box....................................................................................................................................1-2
Product Model Information ...................................................................................................................1-2
Product Specifications .........................................................................................................................1-3
Physical Dimensions............................................................................................................................1-3
Hardware Reference............................................................................................................................1-4
Panel Guide ................................................................................................................................1-4
Ethernet Port .............................................................................................................................. 1-4
LED Indicators ............................................................................................................................1-4
I/O Circuit Diagram............................................................................................................................. 1-5
DI Circuit ...................................................................................................................................1-5
Sinking DO Circuit .......................................................................................................................1-5
Sourcing DO Circuit .....................................................................................................................1-6
DIO Circuit ................................................................................................................................. 1-7
Relay Circuit ...............................................................................................................................1-8
AI Circuit....................................................................................................................................1-8
RTD Circuit .................................................................................................................................1-8
TC Circuit ...................................................................................................................................1-9
2. Initial Setup ...................................................................................................................................... 2-1
Hardware Installation .......................................................................................................................... 2-2
Mounting....................................................................................................................................2-2
Grounding the Unit ......................................................................................................................2-4
I/O Channel Jumper Setting..........................................................................................................2-4
I/O Wiring ..................................................................................................................................2-6
Communication Port Wiring ........................................................................................................ 2-10
Use the Cable Tie Base to Securely Route a Connected I/O Cable .................................................... 2-11
Powering Up the Unit ................................................................................................................. 2-11
ioSearch™ Installation....................................................................................................................... 2-13
Load Factory Default Settings............................................................................................................. 2-13
3. Using the Web Console...................................................................................................................... 3-1
Introduction to the Web Console...........................................................................................................3-2
Overview ...........................................................................................................................................3-3
Network Settings for the Web Console................................................................................................... 3-4
General Settings .........................................................................................................................3-4
Ethernet Configuration .................................................................................................................3-4
User-Defined Modbus Addressing..........................................................................................................3-5
Default Modbus Address ...............................................................................................................3-5
AOPC Server Settings..........................................................................................................................3-6
Tag Generation ........................................................................................................................... 3-6
I/O Settings .......................................................................................................................................3-8
DI Channels................................................................................................................................3-8
DO Channels............................................................................................................................. 3-10
AI Channels .............................................................................................................................. 3-12
AI Input Range ......................................................................................................................... 3-13
AO Channels ............................................................................................................................. 3-15
RTD Channels ........................................................................................................................... 3-16
TC Channels ............................................................................................................................. 3-17
Peer-to-Peer Networking.................................................................................................................... 3-19
Peer-to-Peer Settings (1-50)....................................................................................................... 3-19
Sample Peer-to-Peer Configuration .............................................................................................. 3-20
DO Safe Mode Settings .............................................................................................................. 3-21
AO Safe Mode Settings............................................................................................................... 3-21
SNMP .............................................................................................................................................. 3-21
SNMP Trap ............................................................................................................................... 3-21
Using SNMP .............................................................................................................................. 3-22
Accessibility IP List .................................................................................................................... 3-27
RESTful API Setting........................................................................................................................... 3-28
EtherNet/IP Setting........................................................................................................................... 3-28
System Management......................................................................................................................... 3-28
Network Connection................................................................................................................... 3-28
Firmware Update....................................................................................................................... 3-29
Import System Configuration Settings ......................................................................................... 3-29
Export System Settings.............................................................................................................. 3-29
Change Password ............................................................................................................................. 3-30
Load Factory Defaults........................................................................................................................ 3-30
Save/Restart.................................................................................................................................... 3-30

4. Using ioSearch™................................................................................................................................ 4-1
Introduction to ioSearch™ ...................................................................................................................4-2
ioSearch™ Main Screen ....................................................................................................................... 4-2
Main Screen Overview..................................................................................................................4-2
ioSearch™ Setup ................................................................................................................................4-3
System ......................................................................................................................................4-3
Sort...........................................................................................................................................4-4
Quick Links.................................................................................................................................4-4
Main Function.....................................................................................................................................4-4
Locate........................................................................................................................................4-5
Firmware Upgrade.......................................................................................................................4-5
Unlock ....................................................................................................................................... 4-6
Import .......................................................................................................................................4-6
Export........................................................................................................................................ 4-6
Change IP Address ......................................................................................................................4-7
Batch TCP/IP Configuration on Multiple Devices...............................................................................4-7
Change Server Name ................................................................................................................... 4-8
Activate EtherNet/IP ....................................................................................................................4-8
Restart System ...........................................................................................................................4-9
Reset to Default ..........................................................................................................................4-9
Mass Deployment (Import) ........................................................................................................... 4-9
Mass Deployment (Export) ......................................................................................................... 4-10
5. Activating the EtherNet/IP Function ................................................................................................. 5-1
6. How to Connect the ioLogik E1200 to an Allen-Bradley PLC .............................................................. 6-1
EDS Installation of the ioLogik E1200 Series in Rockwell Software RSLogix 5000 ........................................6-2
Establishing communication between the ioLogik E1200 device and the Allen-Bradley PLC ...........................6-6
7. RESTful API Implementation............................................................................................................. 7-1
Introduction .......................................................................................................................................7-2
Configuring RESTful API Settings ..........................................................................................................7-2
Using RESTful API via a Web Service.....................................................................................................7-2
Troubleshooting Reference...................................................................................................................7-5
A. Modbus/TCP Default Address Mappings ............................................................................................ A-1
Supported Function Code.....................................................................................................................A-2
ioLogik E1210 Modbus Address and Register Map ...................................................................................A-2
ioLogik E1211 Modbus Address and Register Map ...................................................................................A-3
ioLogik E1212 Modbus Address and Register Map ...................................................................................A-5
ioLogik E1213 Modbus Address and Register Map ...................................................................................A-7
ioLogik E1214 Modbus Address and Register Map ...................................................................................A-9
ioLogik E1240 Modbus Address and Register Map ................................................................................. A-11
ioLogik E1241 Modbus Address and Register Map ................................................................................. A-12
ioLogik E1242 Modbus Address and Register Map ................................................................................. A-14
ioLogik E1260 Modbus Address and Register Map ................................................................................. A-16
ioLogik E1262 Modbus Address and Register Map ................................................................................. A-18
B. EtherNet/IP Default Address Mappings............................................................................................. B-1
ioLogik E1200 EtherNet/IP Map ............................................................................................................B-1
C. RESTful API Default Address Mappings ............................................................................................. C-1
ioLogik E1200 RESTful API Map ............................................................................................................C-1
D. Network Port Numbers...................................................................................................................... D-1
E. Factory Default Settings.................................................................................................................... E-1
F. Pinouts.............................................................................................................................................. F-1
G. FCC Interference Statement .............................................................................................................. G-1
H. European Community (CE) ................................................................................................................ H-1
I. Firmware Update Guidelines ..............................................................................................................I-1

1
1. Introduction
The ioLogik E1200 industrial Ethernet remote I/O has two embedded Ethernet switch ports that allow
information to flow to another local Ethernet device or connect to the next ioLogik in a daisy-chain. Applications
such as factory automation, security and surveillance systems, and tunnel monitoring, can make use of
daisy-chained Ethernet for building multidrop I/O networks over standard Ethernet cables and familiar fieldbus
protocols. The daisy-chain function on the ioLogik E1200 Ethernet remote I/O not only increases the
connections between machines and panels, but it also lowers the cost of buying separate Ethernet switches,
and at the same time reduces labor fees and cabling by a large percentage. For example, if a production facility
contains 700 stations (20 points per station), the wiring cost reduction can reach 15% of the total
implementation cost.
The following topics are covered in this chapter:

Product Features

Inside the Box

Product Model Information

Product Specifications

Physical Dimensions

Hardware Reference
Panel Guide
Ethernet Port
LED Indicators

I/O Circuit Diagram
DI Circuit
Sinking DO Circuit
Sourcing DO Circuit
DIO Circuit
Relay Circuit
AI Circuit
RTD Circuit
TC Circuit

ioLogik E1200 Series Introduction
1-2
Product Features
•Active communication with patented MX-AOPC UA Server
•2-port Ethernet switch for daisy-chain topologies
•Easy mass deployment and configuration with ioSearch™utility
•User-friendly configuration via web browser
•Save time and wiring costs with peer-to-peer communication
•User-defined Modbus/TCP addressing
•Simplify I/O management with MXIO library on either Windows or Linux platform
•Wide operating temperature: -40 to 75°C (-40 to 167°F)
•Supports SNMPv1/v2c
•UL/cUL Class I Division 2, ATEX Zone 2 certification
Inside the Box
The ioLogik E1200 is shipped with the following items:
•ioLogik E1200 remote Ethernet I/O server
•Quick installation guide (printed)
NOTE
Notify your sales representative if any of the above items are missing or damaged.
Product Model Information
Model Description
ioLogik E1210 Remote Ethernet I/O with 2-port Ethernet switch and 16 DIs
ioLogik E1211 Remote Ethernet I/O with 2-port Ethernet switch and 16 DOs
ioLogik E1212
Remote Ethernet I/O with 2-port Ethernet switch, 8 DIs, and 8 DIOs
ioLogik E1213 Remote Ethernet I/O with 2-port Ethernet switch, 8 DIs, 4 DOs, and 4 DIOs (source type)
ioLogik E1214 Remote Ethernet I/O with 2-port Ethernet switch, 6 DIs, and 6 relays
ioLogik E1240 Remote Ethernet I/O with 2-port Ethernet switch and 8 AIs
ioLogik E1241 Remote Ethernet I/O with 2-port Ethernet switch and 4 AOs
ioLogik E1242 Remote Ethernet I/O with 2-port Ethernet switch and 4 AIs, 4DIs, and 4DIOs
ioLogik E1260 Remote Ethernet I/O with 2-port Ethernet switch and 6 RTDs
ioLogik E1262 Remote Ethernet I/O with 2-port Ethernet switch and 8 TCs
ioLogik E1210-T
Ethernet remote I/O with 2-port Ethernet switch and 16 DIs, -40 to 75°C operating
temperature
ioLogik E1211-T Ethernet remote I/O with 2-port Ethernet switch and 16 DOs, -40 to 75°C operating
temperature
ioLogik E1212-T
Ethernet remote I/O with 2-port Ethernet switch, 8 DIs, and 8 DIOs, -40 to 75°C
operating temperature
ioLogik E1213-T Remote Ethernet I/O with 2 Port Ethernet switch, 8 DIs, 4 DOs, and 4 DIOs (source
type), -40 to 75°C operating temperature
ioLogik E1214-T
Ethernet remote I/O with 2-port Ethernet switch, 6 DIs, and 6 Relays, -40 to 75°C
operating temperature
ioLogik E1240-T Ethernet remote I/O with 2-port Ethernet switch and 8 AIs, -40 to 75°C operating
temperature
ioLogik E1241-T
Ethernet remote I/O with 2-port Ethernet switch and 4 AOs , -40 to 75°C operating
temperature
ioLogik E1242-T Ethernet remote I/O with 2-port Ethernet switch, 4 AIs, 4 DIs, and 4 DIOs, -
40 to 75°C
operating temperature
ioLogik E1260-T
Ethernet remote I/O with 2-port Ethernet switch and 6 RTDs, -40 to 75°C operating
temperature
ioLogik E1262-T Ethernet remote I/O with 2-port Ethernet switch and 8 TCs, -40 to 75°C operating
temperature

ioLogik E1200 Series Introduction
1-3
Product Specifications
NOTE
The latest specifications for Moxa’s products can be found at
https://www.moxa.com.
Physical Dimensions

ioLogik E1200 Series Introduction
1-4
Hardware Reference
Panel Guide
NOTE
The
RESET button restarts the server and resets all settings to factory defaults. Use a pointed object such as
a straightened paper clip to hold down the RESET button for 5 seconds. The factory defaults will be loaded once
the READY LED turns green again. You
may then release the RESET button.
Ethernet Port
Pin 1 2 3 4
Signal TXD+ TXD- RXD+ ---
Pin 5 6 7 8
Signal --- RXD- --- ---
LED Indicators
LED State Description
Power Amber System power is ON
OFF System power is OFF
Ready Green System is ready
Flashing Flashes every 1 second when the “Locate” function is triggered
Flashing Flashes every 0.5 second when the firmware is being upgraded
Flashing ON/OFF cycle period of 0.5 second represents “Safe Mode”
OFF System is not ready
Port 1 Green Ethernet connection enabled
Flashing Transmitting or receiving data
Port 2 Green Ethernet connection enabled
Flashing Transmitting or receiving data
EXT Green EXT field power input is connected
Off EXT field power input is disconnected

ioLogik E1200 Series Introduction
1-5
I/O Circuit Diagram
DI Circuit
Sinking DO Circuit

ioLogik E1200 Series Introduction
1-6
Sourcing DO Circuit

ioLogik E1200 Series Introduction
1-7
DIO Circuit

ioLogik E1200 Series Introduction
1-8
Relay Circuit
AI Circuit
RTD Circuit

ioLogik E1200 Series Introduction
1-9
TC Circuit

2
2. Initial Setup
This chapter describes how to install the ioLogik E1200.
The following topics are covered in this chapter:

Hardware Installation
Mounting
Grounding the Unit
I/O Channel Jumper Setting
I/O Wiring
Communication Port Wiring
Use the Cable Tie Base to Securely Route a Connected I/O Cable
Powering Up the Unit

ioSearch™ Installation

Load Factory Default Settings

ioLogik E1200 Series Initial Setup
2-2
Hardware Installation
Read all of the safety notifications and warnings below before installing the product.
ATTENTION
This unit is sensitive to Electrostatic Discharge, which can cause internal damage and affect normal operation.
Follow the
se guidelines when you handle this unit:
•
Before handling the product, touch a grounded object to discharge static electricity from your body.
•
Wear an approved grounding wristband.
•
Do not touch connectors or pins on component boards.
•
Do not touch circuit components inside the equipment.
•
Use a static-safe workstation, if available.
•
Store the equipment in appropriate static-safe packaging when not in use.
WARNING
Disconnect
the power when you want to remove or replace components or disconnect equipment,
unless the
area is known to be free of ignitable
material.
•
If you connect or disconnect the Removable Terminal Block while field power is applied to the product
, an
electrical arc could occur. The arc could cause an explosion in hazardous location installations. Make
sure
the power is disconnected, or the area is nonhazardous before starting the installation process.
•
If you connect or disconnect wiring while the field-side power is applied to the product, an electrical arc
could occur. The arc could cause an explosion in hazardous location installations. Make sure the
power is
disconnected or the area is nonhazardous before starting the installation process.
•
Do not disconnect the unit unless the power has been disconnected or the area is known to be
nonhazardous. In a hazardous area, the unit must be powered down before removal.
Mounting
The unit supports two types of mounting: DIN-Rail Mounting and Wall Mounting. While mounting the unit, be
sure to use the correct tools and accessories to ensure that the unit is property mounted.
DIN Rail
Take the following steps to mount the unit on a DIN rail:
STEP 1
. Pull down the bottom of the two sliders on the back of the unit.

ioLogik E1200 Series Initial Setup
2-3
STEP 2
. Latch the top slider of the unit onto the DIN rail
as
shown in the diagram.
Reserve at least 10 cm of space
above
the DIN rail to ensure
that there is enough space to
complete the
installation.
STEP 3.
Rotate the unit down into a vertical position, and then p
ush
the bottom slider
back up to its original position
to lock the unit to
the DIN rail
.
STEP 4.
At this point, if the mounting was done correctly, t
he unit
sh
ould be securely fixed to the DIN Rail.
Wall Mounting
STEP 1. There are two sliders
on the back of the unit, pull out both slider
s out away from the
product
.

ioLogik E1200 Series Initial Setup
2-4
STEP 2. Use screws to fix the unit to the wall, as shown in the
diagram.
Reserve at least 1.5 cm of space above and below
the unit to ensure
that the installation can be done correctly.
STEP 3.
At this point, if the mounting was done correctly, the unit should be
securely
fixed to the wall.
Grounding the Unit
Top View
The ioLogik E1200
has a grounding point located on the top
panel
of
the terminal block. Connect the ground pin ( ) to earth
ground.
Item Suggested Setting
Wire range 12 to 24 AWG
Screw Torque 7 lb-inch
I/O Channel Jumper Setting
The following table shows jumper setting for each model of the ioLogik E1200 Series. We provide a more
detailed description of three different jumper settings.
Model Jumper Setting
E1212 DIO direction (DI, DO)
E1213 1. DIO direction (DI, DO)
2. EXT Power Configuration
E1240 AI mode (Voltage, Current)
E1242 1. DIO direction (DI, DO)
2. AI mode (Voltage, Current)

ioLogik E1200 Series Initial Setup
2-5
Take the following to open up the unit.
Rear View
STEP 1. Remove the screw
from the back panel.
(Suggested Torque: 3.9 ± 0.4 kg
-cm)
Top View
STEP 2. Remove the Terminal Block and open the top cover as
shown in the diagram
.
STEP 3.
The jumpers are located near the IO
channels.
Jumper settings for different modes of
operation are described below. In the diagrams,
a triangle is used to indicate the direction of the
setting.
DIO Direction (DI, DO)
DIO mode configuration settings are shown below:
The default setting is DO Mode.
AI mode (Voltage, Current)
Analog mode configuration settings are shown below:
The default setting is Voltage Mode.

ioLogik E1200 Series Initial Setup
2-6
EXT Power Configuration
The ioLogik E1213 comes with a source type DO, which has three possible external (EXT) power configurations.
Only one field power configuration can be selected at a time (JP10 / 12V JP5 / 9V JP11), and the jumper must
be inserted vertically, not horizontally. EXT power configuration settings are shown below:
Example:
If jumper is set to 12V,
EXT power will be 12V.
The default setting is Field Power JP10.
NOTE
The ioLogik E1213 has 4 pure DO channels and 4 hybrid DIO channels. For the 4 pure DO channels, you can use
the jumpers to select th
e power configuration output (e.g., field power:
12 V, 9 V). But for the 4 hybrid DIO
channels, you cannot use the jumpers to select the power configuration output. Instead, you can only use the
jumpers to set the DIO channels to either DI mode or DO mode.
I/O Wiring
The following wiring guide explains how to configure seven different types of I/O channel:
Item Suggested Setting
Wire range 16 to 26 AWG
Screw Torque 3 lb-inch
A Dry Contact is a contact that works without a power source. This applies to buttons, switches, etc.
A Wet Contact is a contact that must be connected to a power source to work. This applies to proximity
sensors, motion sensors, etc.
Check the sensor type (NPN, PNP) and follow the corresponding wiring instructions.
DI Dry Contact

ioLogik E1200 Series Initial Setup
2-7
DI Wet Contact (NPN)
DI Wet Contact (PNP)
DO (Sink Type)
DO (Source Type)
Relay