Moxa Technologies ioLogik E1500 Series User manual

P/N: 1802015000012
*1802015000012*
ioLogik E1500 Series
Quick Installation Guide
Ethernet Remote I/O
Edition 3.0, December 2016
Technical Support Contact Information
www.moxa.com/support
Moxa Americas:
Toll
-free: 1-888-669-2872
Tel:
1-714-528-6777
Fax:
1-714-528-6778
Moxa China (Shanghai office):
Toll
-free: 800-820-5036
Tel:
[phone]
Fax:
[phone]
Moxa Europe:
Tel:
[phone]
Fax:
[phone]
Moxa Asia-Pacific:
Tel:
[phone]
Fax:
[phone]
Moxa India:
Tel:
[phone]
Fax:
[phone]

2016 Moxa Inc. All rights reserved.

- 2 -
Package Checklist
•1 ioLogik E1500 series remote I/O product
•Quick installation guide (printed)
Specifications
System
Ethernet
10/100 Mbps, M12 connector
Protection
1.5 KV magnetic isolation
Protocols
Modbus/TCP, TCP/IP, UDP, DHCP, Bootp, HTTP
Power Input
24 VDC nominal, 12 to 48 VDC
Wiring
I/O cable, max. 14 AWG
Dimensions
144 x 124 x 30 mm (5.67 x 4.88 x 1.18 in)
Weight
825 g
Operating Temperature
-40 to 85°C (-40 to 185°F)
Storage Temperature
-40 to 85°C (-40 to 185°F)
Ambient Relative
Humidity
5 to 95% (non-condensing)
Altitude:
Up to 2000 m
Note: Please contact Moxa if you require products guaranteed to function
properly at higher altitudes.
Standards and
Certifications
UL 508, EN 50155, EN 50121-3-2, EN 50121-4
Warranty Period
5 years
Details
See www.moxa.com/warranty
Digital Input
Sensor Type
NPN, PNP, and Dry contact
I/O Mode
DI or Event Counter
Dry Contact
• On: short to GND
• Off: open
Wet Contact
• On: 0 to 3 VDC
• Off: 10 to 30 VDC
Isolation
3k VDC or 2k Vrms
Counter/Frequency
250 Hz, power off storage
Digital Output
I/O Mode
DO or Pulse Output
Pulse Wave
Width/Frequency
1 ms/500 Hz
Over-voltage Protection
45 VDC
Over-current Protection
2.6 A (4 channels @ 650 mA)
Over-temperature
Shutdown
175°C (typical), 150°C (min.)
Current Rating
200 mA per channel
Isolation
3k VDC or 2k Vrms

- 3 -
Installation
I/O Wiring
DI dry contact mode
DI wet contact mode (Ch-Ch isolation)
DI wet contact PNP/NPN mode (No CH-CH isolation)
DIO_DI wet contact mode (no CH-CH isolation)

- 4 -
DIO_DO sink mode
Mounting and Cabling
The ioLogik E1500 can be used with both DIN rail and wall mounts. When
mounting on a DIN rail, release the bottom mounting kit, install the
ioLogik on the rail, and then restore the bottom mounting kit to fix the
ioLogik to the rail. When using wall mounting, release both the upper and
bottom DIN rail kits.
The ioLogik E1500 has an M12 Ethernet port for connecting either a
standard direct-Ethernet or crossover-Ethernet cable via a locking M12
connector.
Power and Networking
Connect the +12 to +48 VDC power line to the ioLogik E1500’s terminal
block V+ terminal, and connect the ground from the power supply to the
V- terminal. If an earth ground is available, connect the ground pin
( ).
LED Indicators
Type
Color
Description
PWR
Green
System power in ON
Off
System power is OFF
RDY
Green
System is ready
Green Blinking
Located
Red
System Booting-up Error
Green/Red
Blinking
Safe Mode
Red Blinking
Firmware upgrade (LED flashes for 3
seconds then stays red until restart)
Off
System is not ready
LAN
Green
100 Mbps
Amber
10 Mbps
Blinking
Data Transmitting
Off
Ethernet Off

- 5 -
Type
Color
Description
EXP
Green
Expansion Mode Ready
Red
Configuration Failure
Off
Stand-alone Mode
DI
Green
Channel ON
Off
Channel OFF
DIO
Green
Channel ON
Off
Channel OFF
System Configuration
Configuration via Web Console
Configuration of an ioLogik E1500 is done via the web console.
•Default IP Address: 192.168.127.254
•Subnet Mask: 255.255.255.0
Note: Be sure to configure the host PC’s IP address to the same subnet as
the ioLogik E1500. For example, 192.168.127.253.
ioSearch Utility
ioSearch is a search utility that helps users locate an ioLogik E1500 on the
local network. The latest version of the utility can be downloaded from
Moxa's website.
Load Factory Default Settings
There are three ways to restore the ioLogik E1500 to the factory default
settings.
1. Remove the two screws and the aluminum plate, and then press and
hold the RESET button for 5 seconds.
2. Right click the specified ioLogik in the ioSearch utility and select
Reset to Default.
3. Select Load Factory Default from the web console.
Modbus Address Table
Refer to the user’s manual for details of the ioLogik’s Modbus address, or
refer to the start address of the I/O channels in the web console under
User-defined Modbus Addressing Default Address.

- 6 -
How to Download the Software
Step 1: Click on the following link to open the Support & Downloads
search tool:
http://www.moxa.com/support/support_home.aspx?isSearchShow=1
Step 2: Type the model name in the search box or select a product from
the drop down box and then click Search.
Step 3: Click the Software Packages link to download the latest
software for the product.