Moxa Technologies MGate 5118 Series User manual

P/N: 1802051180011
*1802051180011*
MGate 5118
Quick Installation Guide
Edition 1.1, October 2018
Technical Support Contact Information
www.moxa.com/support
Moxa Americas:
Toll
-free: 1-888-669-2872
Tel:
1-714-528-6777
Fax:
1-714-528-6778
Moxa China (Shanghai office):
Toll
-free: 800-820-5036
Tel:
[phone]
Fax:
[phone]
Moxa Europe:
Tel:
[phone]
Fax:
[phone]
Moxa Asia-Pacific:
Tel:
[phone]
Fax:
[phone]
Moxa India:
Tel:
[phone]
Fax:
[phone]

2018 Moxa Inc. All rights reserved.

- 2 -
Overview
The MGate 5118 is an industrial Ethernet gateway for J1939-to-Modbus
RTU/ASCII/TCP, PROFINET and EtherNet/IP network communications.
Package Checklist
Before installing the MGate 5118, verify that the package contains the
following items:
•1 MGate 5118 gateway
•Quick installation guide (printed)
•Warranty card
Please notify your sales representative if any of the above items is
missing or damaged.
Optional Accessories (can be purchased separately)
•Mini DB9F-to-TB: DB9-female-to-terminal-block connector
•WK-51-01: Wall-mounting kit, 51 mm wide
Hardware Introduction
LED Indicators
LED
Color
Description
PWR 1,
PWR 2
Green
The power cable is connected
Off
The power cable is disconnected
Ready
Off
Power is off or a fault condition exists
Green Steady on: Power is on, and the unit is functioning
normally
Blinking: The unit is responding to the software’s
Locate function
Red Steady on: Power is on, and the unit is booting up
Blinking: Indicates an IP conflict, or the DHCP or
BOOTP server is not responding properly
Flashing quickly: the microSD card failed
LAN
Green
(Flashing
only)
The Ethernet port is receiving or transmitting data
Modbus TCP Client:
Modbus communication in progress
Modbus TCP Server:
Modbus communication in progress
EIP Scanner:
I/O is exchanging data with at least one device
EIP Adapter: I/O is exchanging data
PROFINET: PROFINET I/O interface is exchanging
data

- 3 -
LED
Color
Description
Red
(Flashing
only)
A communication error occurred
Modbus TCP Client:
1. Received an exception code or framing error
(parity error, checksum error)
2. Command timeout (slave device is not
responding)
3. TCP connection timeout
Modbus TCP Server:
1. Received an invalid function code or framing
error (parity error, checksum error)
2. Accessed invalid register address or coil address
Ethernet/IP Scanner:
1. Command timeout (the adapter is not
responding)
2. TCP connection timeout
Ethernet/IP Adapter:
The connection was refused due to incorrect
configuration
Off
No communication
MB* Green
(Flashing
only)
Modbus is receiving or transmitting data
Red
(Flashing
only)
A communication error occurred
Master Mode:
1. Received an exception code or framing error
(parity error, checksum error)
2. Command timeout (the slave device is not
responding)
Slave Mode:
1. Received an invalid function code or framing
error (parity error, checksum error)
2. Accessed invalid register address or coil address
Off
No communication
CAN Green
(Flashing
only)
CANbus(J1939) communication is receiving or
transmitting data
Red
(Steady)
A communication error occurred
1. The J1939 address claim failed
2. CAN is in bus-off state because the error counter
is exceeding its limitations
Off
No communication
Eth1,
Eth2
Green
Indicates an 100 Mbps Ethernet connection
Amber
Indicates a 10 Mbps Ethernet connection
Off
The Ethernet cable is disconnected
*Only indicates serial communication status; for Modbus TCP status,
please refer to LAN LED indicator.

- 4 -
Dimensions
Unit = mm (inch)
Reset Button
Restore the MGate to factory default settings by using a pointed object
(such as a straightened paper clip) to hold the reset button down until
the Ready LED stops blinking (approximately five seconds).
Pull-high, Pull-low, and Terminator for RS-485 and CAN
On the MGate 5118’s left side panel, you will find DIP
switches to adjust each CAN port or serial port’s pull
-
high resistor, pull
-low resistor, and terminator.
SW
CAN
MODBUS
1
2
3
1
2
3
Pull-
high
resistor
Pull-low
resistor
Terminator
Pull-high
resistor
Pull-low
resistor
Terminator
ON
Reserved
120 Ω
(default)
1 kΩ 1 kΩ 120 Ω
OFF –
150 kΩ
(default)
150 kΩ
(default)
– (default)
Hardware Installation Procedure
1. Connect the power adapter. Connect the 12-48 VDC power line or
DIN-rail power supply to the MGate 5118’s terminal block.
2. Use a serial cable to connect the MGate to the Modbus or CAN
device.
3. Use an Ethernet cable to connect the MGate to the Modbus,
Ethernet/IP or PROFINET device.
4. The MGate 5118 is designed to be attached to a DIN rail or
mounted on a wall. For DIN-rail mounting, push down the spring

- 5 -
and properly attach it to the DIN rail until it “snaps” into place. For
wall mounting, install the wall-mount kit (optional) first and then
screw the device onto the wall. The following figure illustrates the
two mounting options:
Software Installation Information
You can download the User's Manual and DSU (Device Search Utility)
from Moxa's website: www.moxa.com. Please refer to the User’s
Manual for additional details on using the Device Search Utility.
The MGate 5118 also supports login via a web browser.
Default IP address: 192.168.127.254
Default account: admin
Default password: moxa
Pin Assignments
Modbus Serial Port (Male DB9)
Pin RS-232
RS-422/
RS-485 (4W)
RS-485 (2W)
1
DCD
TxD-(A)
–
2
RXD
TxD+(B)
–
3
TXD
RxD+(B)
Data+(B)
4
DTR
RxD-(A)
Data-(A)
5*
GND
GND
GND
6
DSR
–
–
7
RTS
–
–
8
CTS
–
–
9
–
–
–
*Signal ground
CAN Port (6-pin Terminal Block)
Pin
CAN
1
CAN_L
2
CAN_H
3
CAN Signal GND
4
Ext-CAN_L*
5
Ext-CAN_H*
6
CAN_SHLD

- 6 -
* For the CAN port, plug CAN_L and CAN_H into the terminal block. If
another device is connected to the same CAN bus, use the Ext_CAN_L
and Ext_CAN_H as extension pins.
Ethernet Port (RJ45)
Pin
Signal
1
Tx+
2
Tx-
3
Rx+
6
Rx-
Console Port (RS-232)
The MGate 5118 series can use a RJ45 serial port to connect to a PC to
configure the device.
Pin
Signal
1
DSR
2
RTS
3
GND
4
TXD
5
RXD
6
DCD
7
CTS
8
DTR
Power Input and Relay Output Pinouts
V2+ V2- V1+ V1-
Shielded
Ground
DC
Power
Input 2
DC
Power
Input 2
N.O. Common
N.C.
DC
Power
Input 1
DC
Power
Input 1
Specifications
Power Requirements
Power Input
12 to 48 VDC
Power Consumption
416mA@12VDC, 195mA@24VDC,
110mA@48VDC
Operating Temperature
Standard model:
0 to 60°C (32 to 140°F)
Wide temperature model:
-40 to 75°C (-40 to 167°F)
Ambient Relative Humidity
5 to 95% RH
Dimensions
45.8 x 105 x 134 mm (1.80 x 4.13 x 5.27
in)
Reliability
Alert Tools
Built-in buzzer and RTC
MTBF
727,873 hrs.

- 7 -
NOTE
In the following section, ATEX and C1D2 certifications will be
detailed separately.
ATEX Information
1. DEMKO Certificate number: 17 ATEX 1848X
IECEx Certificate number: IECEx UL 17.0019X
2. Ambient Temperature Range:
0°C to 60°C (for models without suffix –T)
-40°C to 75°C (for models with suffix –T only)
3. Certification String: Ex nA nC IIC T4 Gc
4. Standards Covered: EN 60079-0:2012+A11:2013/IEC 60079-0 6th
Ed. AND EN 60079-15:2010/IEC 60079-15 4th Ed.
5. The conditions of safe use:
a. The equipment shall be installed in an enclosure that provides a
degree of protection not less than IP 54 in accordance with
IEC/EN 60079-15 and accessible only by the use of a tool.
b. Devices are for use in an area of not more than pollution
degree 2 in accordance with IEC/EN 60664-1.
c. Provisions shall be made, either in the equipment or external to
the equipment, to prevent the rated voltage from being
exceeded by the transient disturbances of more than 140% of
the peak-rated voltage.
Installation instructions
a. When wiring the relay contact (R), digital input (DI), and power
inputs (P1/P2), we suggest using AWG (American Wire Gauge) 12-28
(0.0804-3.31 mm²) as a cable and the corresponding pin-type cable
terminals. The connector can withstand a maximum torque of 4.5 inch-
pounds.
b. Conductors suitable for use in an ambient temperature of 85°C must
be used for the power input terminal block.
c. The cross-sectional area of the earthing conductors shall be at least
3.31 mm²
C1D2 Information
1. These devices are open-type devices that are to be installed in an
enclosure only accessible with the use of a tool and suitable for the
environment.
2. This equipment is suitable for use in Class I, Division 2, Groups A, B,
C, and D or non-hazardous locations only.”
WARNING
EXPLOSION HAZARD
Do not disconnect the equipment unless the power has been
switched off, or the area is known to be nonhazardous.

- 8 -
WARNING
EXPLOSION HAZARD
The substitution of any components may impair suitability for
Class 1, Division 2.
WARNING
EXPOSURE TO SOME CHEMICALS MAY DEGRADE THE SEALING
PROPERTIES OF MATERIALS USED IN THE FOLLOWING
DEVICE: Sealed Relay Device U21.
WARNING
EXPLOTION HAZARD
Indoor use and Pollution degree 2.
WARNING
EXPLOTION HAZARD
The equipment and label must be wiped by a dry cloth.
WARNING
EXPLOTION HAZARD
This unit is intended
to be supplied by an UL Listed/IEC 60950-
1 approved power supply suitable for use at 75°C. And the
power supply output meets SELV, LPS and rated output 12
-48
VDC, and 416 mA minimum.
Moxa Inc.
Fl. 4, No. 135, Lane 235, Baoqiao Rd.
Xindian Dist., New Taipei City, 23145
Taiwan, R.O.C.