Moxa Technologies UPORT 1100 series User manual

UPort 1100 Series User’s Manual
Fourth Edition, April 2009
www.moxa.com/product
©2009 Moxa Inc. All rights reserved.
Reproduction without permission is prohibited.

UPort 1100 Series User’s Manual
The software described in this manual is furnished under a license agreement and may be used only in
accordance with the terms of that agreement.
Copyright Notice
Copyright ©2009 Moxa Inc.
All rights reserved.
Reproduction without permission is prohibited.
Trademarks
MOXA is a registered trademark of Moxa Inc.
All other trademarks or registered marks in this manual belong to their respective manufacturers.
Disclaimer
Information in this document is subject to change without notice and does not represent a commitment on the
part of Moxa.
Moxa provides this document “as is,” without warranty of any kind, either expressed or implied, including, but
not limited to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this
manual, or to the products and/or the programs described in this manual, at any time.
Information provided in this manual is intended to be accurate and reliable. However, Moxa Technologies
assumes no responsibility for its use, or for any infringements on the rights of third parties that may result from
its use.
This product might include unintentional technical or typographical errors. Changes are periodically made to the
information herein to correct such errors, and these changes are incorporated into new editions of the
publication.
Technical Support Contact Information
www.moxa.com/support
Moxa Americas:
Toll-free: 1-888-669-2872
Tel:[phone]
Fax:[phone]
Moxa China (Shanghai office):
Toll-free: 800-820-5036
Tel:[phone]
Fax:[phone]
Moxa Europe:
Tel:[phone]
Fax:[phone]
Moxa Asia-Pacific:
Tel:[phone]
Fax:[phone]

Table of Contents
Chapter 1 Introduction..............................................................................................1-1
Overview............................................................................................................................ 1-2
ADDC™ (Automatic Data Direction Control) for RS-485..................................... 1-2
ARDC (Automatic Recovery Data Communication).............................................. 1-2
Package Checklist .............................................................................................................. 1-2
Product Features................................................................................................................. 1-3
Product Specifications........................................................................................................ 1-3
LED Indicators................................................................................................................... 1-5
Adjustable Pull High/low, Terminator Resistors for the RS-485 Port.................... 1-6
Chapter 2 Installation and Configuration................................................................2-1
Initial Driver Installation.................................................................................................... 2-2
Hardware Installation.............................................................................................. 2-5
Windows 98/ME and Windows 2000 ..................................................................... 2-5
Windows XP, Windows 2003, and Windows Vista (32-bit and 64-bit) ................. 2-6
Configuring the COM Port ................................................................................... 2-12
Configuring the Converter .................................................................................... 2-13
Removing the Converter....................................................................................... 2-16
Uninstalling the Driver.......................................................................................... 2-17
Install Linux Driver.......................................................................................................... 2-18
Linux Kernel 2.4.20 and above............................................................................. 2-18
Linux Kernel 2.6.x................................................................................................ 2-19
Installing the Windows CE Driver ................................................................................... 2-21
Installation with an installation package for Win CE 6.0...................................... 2-22
Installation with an installation package for Win CE 5.0...................................... 2-30
Removing the Moxa WinCE 5.0 / CE 6.0 Driver ................................................. 2-32
Installation with a CAB File ................................................................................. 2-33
Removing the Moxa WinCE 5.0 / CE 6.0 Driver ................................................. 2-35
Chapter 3 Pin Assignment .......................................................................................3-1
UPort DB9 Pin Assignments.............................................................................................. 3-1
Terminal Block Pin Assignments ....................................................................................... 3-1

1
1
Chapter 1 Introduction
The UPort 1100 Series of USB-to-serial converters provide an easy way to add COM ports to your
computer. The UPort 1110 provides one RS-232 port, the UPort 1130 provides one
RS-422/RS-485 port, and the UPort 1150 and UPort 1150I each provide one RS-232/422/485 port.
As a plug and play USB device, the converters are perfect for mobile, instrumentation, and
point-of sale applications.
The UPort 1100 series include the following models:
UPort 1110: 1-port RS-232 USB-to-serial converter.
UPort 1130: 1-port RS-422/485 USB-to-serial converter.
UPort 1150: 1-port RS-232/422/485 USB-to-serial converter.
UPort 1150I: 1-port RS-232/422/485 USB-to-serial converter w/ isolation protection.
The following topics are covered in this chapter:
Overview
¾ADDC™ (Automatic Data Direction Control) for RS-485
¾ARDC (Automatic Recovery Data Communication)
Package Checklist
Product Features
Product Specifications
LED Indicators
¾Adjustable Pull High/low, Terminator Resistors for the RS-485 Port

UPort 1100 Series User’s Manual Introduction
Overview
The UPort 1110, UPort 1130, and UPort 1150/1150I are part of Moxa’s UPort line of
USB-to-serial converters. The UPort line provides a range of easy-to-use solutions for adding
COM ports through a PC’s USB port. Simply install the drivers, connect the UPort to your
computer, plug in your serial devices, and you’re ready to go. Programming is not required, and
you do not need to worry about IRQs, configuring a board, power requirements, or connection
schemes.
The UPort 1100 series provides single COM port expansion. The UPort 1110 adds one RS-232
port to your computer, which is the same type of COM port that is built into most PC
motherboards. The UPort 1130 adds one port that is configurable for RS-422, 2-wire RS-485, and
4-wire RS-485 modes. The UPort 1150/1150I adds one RS-232, RS-422, 2 wire RS-485, or 4 wire
RS-485 port to your computer. All of these models can operate at speeds of up to 12 Mbps, which
is much faster than the current maximum serial transfer rate. In addition, the UPort
1130/1150/1150I support ADDC™ (Automatic Data Direction Control) for RS-485 transmission.
The converter is bus-powered, so no external power supply is required.
ADDC™ (Automatic Data Direction Control) for RS-485
ADDC™ (Automatic Data Direction Control) makes it easier to manage 2-wire RS-485
half-duplex connections, eliminating the need for software interference. This means that it is not
necessary to write extra code for Windows applications to control the half-duplex protocol.
ADDC™ intelligence is built into all UPort products that support RS-485 transmission.
ARDC (Automatic Recovery Data Communication)
ARDC (Automatic Recovery Data Communication) makes it easier to recover data transmission,
even if the cable is accidentally unplugged. This means that you do not need to worry about
reconfiguring complex settings to ensure smooth data transmission. If the USB cable is
accidentally unplugged, simply plug it back into the same port and the converter will automatically
reconnect with the host and continue to transfer data. This feature not only eliminates the need for
reconfiguration, but also reduces the probability of data loss.
Package Checklist
The following items are included in your UPort package:
yUPort 1100 Series USB-to-serial converter
yUPort Documentation and Software CD
yUPort 1100 Series Quick Installation Guide
y5-year Warranty Statement
The UPort 1130/1150/1150I also come with the following item:
yMini DB9F-to-Terminal-Block Converter
NOTE: Please notify your sales representative if any of the above items are missing or damaged.
1-2

UPort 1100 Series User’s Manual Introduction
Product Features
The UPort converter has the following features:
yFull-Speed USB operation at up to 12 Mbps
yAdditional I/O or IRQ not required
ySerial transmission speed up to 921.6 Kbps
y64-byte FIFO and built-in hardware and software flow control
yBuilt-in 15 KV ESD protection
ySupport for RS-422, 2-wire RS-485, and 4-wire RS-485 (UPort 1130/1150/1150I)
yTerminal block adaptor (UPort 1130/1150/1150I)
y2 KV Optical Isolation Protection (UPort 1150I only)
Product Specifications
USB
Version USB 1.1 (also compatible with USB 1.0 and 2.0)
Connector USB type B
Speed 12 Mbps
Serial Interface
No. of Ports 1
RS-232 TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
RS-422 TxD+(B), TxD-(A), RxD+(B), RxD-(A),GND
RS-485 4-wire: TxD+(B), TxD-(A), RxD+(B), RxD-(A), GND 2-wire:
Data+(B), Data-(A), GND
RS-485 Data Direction
Control: ADDC™ (Automatic Data Direction Control)
Connector Male DB9
FIFO 64 bytes
Serial line protection 15 KV ESD for all signals
Serial Communication Parameters
Parity None, Even, Odd, Space, Mark
Data bits 5, 6, 7, 8
Stop bits 1, 1.5, 2
Flow control UPort 1130: XON/XOFF
UPort 1110/1150/1150I: RTS/CTS, XON/XOFF
Speed 50 bps to 921.6 Kbps
Power Requirements
Power Consumption
UPort 1110: 30mA@5VDC
UPort 1130: 90mA@5VDC
UPort 1150: 77mA@5VDC
UPort 1150I: 260mA@5VDC
Mechanical
Dimensions UPort 1110/1130/1150: 37.5 x 20.5 x 60 mm (L x W x H)
UPort 1150I: 52 x 80 x 22 mm (L x W x H)
1-3

UPort 1100 Series User’s Manual Introduction
Material UPort 1110/1130/1150: ABS + PC
UPort 1150I: Metal
Gross Weight UPort 1110/1130/1150: 60 g (0.13 lb)
UPort 1150I: 80 g (0.17 lb)
Environmental
Operating Temperature 0°C to 55°C (32°F to 131°F)
Storage Temperature -20°C to 70°C (-4°F to 185°F)
Operating Humidity 5% RH to 95% RH
Regulatory Approvals
EN55022 Class B, EN55024, EN61000-3-2, EN61000-3-3, IEC
61000-4-2, IEC 61000-4-3, IEC 61000-4-4, IEC 61000-4-5, IEC
61000-4-8, IEC 61000-4-11, FCC Part 15 Class B
Warranty
5 years
1-4

UPort 1100 Series User’s Manual Introduction
LED Indicators
Active
RxD
TxD
1110
USB-to-Serial Adaptor
Active
RxD
TxD
1130
USB-to-Serial Adaptor
Active
RxD
TxD
1150
USB-to-Serial Adaptor
RS-232/422/485
UPort 1110 UPort 1130 UPort 1150 UPort 1150 I
UPort 1110/1130/1150 LED description:
Name Color Description
Active Red
This LED indicates normal operation.
Steady: The UPort is operational.
Off: Fault condition exists. There may be a problem with the converter,
the driver installation, or PC configuration.
TxD Green Blinking: Serial device is transmitting data.
RxD Yellow Blinking: Serial device is receiving data.
UPort 1150I LED description:
Name Color Description
Active Red
Steady: The UPort is operational.
Off: Fault condition exists. There may be a problem with the converter,
the driver installation, or PC configuration.
TxD Green Blinking: Serial device is transmitting data.
RxD Yellow Blinking: Serial device is receiving data.
DTR, DSR,
RTS, CTS,
DCD Red Steady: Require these signals to operate.
Off: Disable these signals to operate.
1-5

UPort 1100 Series User’s Manual Introduction
TR
150 KX
1K
21
ON DIP
3
Adjustable Pull High/low, Terminator Resistors for the RS-485 Port
In some critical environments, you may need to add termination resistors to prevent the reflection
of serial signals. When using termination resistors, it is important to set the pull high/low resistors
correctly so that the electrical signal is not corrupted. The UPort uses DIP switches to set the pull
high/low resistor values for each serial port.
To set the pull high/low resistors to 150 KΩ, make sure both of the assigned DIP switches are in
the OFF position.
To set the pull high/low resistors to 1 KΩ, make sure both of the assigned DIP switches are in
the ON position. This is the default setting.
1 2 3
SW Pull High Pull Low Terminator
ON 1KΩ1KΩ120 Ω
OFF 150 KΩ150 KΩDisable
1-6

2
2
Chapter 2 Installation and Configuration
Installation of the converter is a simple process. First install the driver, then plug the converter into
a USB port. When the converter is plugged in, Windows will load the correct drivers for the
converter and the new COM port. In this chapter, basic installation and configuration procedures
are explained. Although the installation screens will be for Windows 2000, the procedures are
essentially the same for Windows 98 and later versions.
The following topics are covered in this chapter:
Initial Driver Installation
¾Hardware Installation
¾Windows 98/ME and Windows 2000
¾Windows XP, Windows 2003, and Windows Vista (32-bit and 64-bit)
¾Configuring the COM Port
¾Configuring the Converter
¾Removing the Converter
¾Uninstalling the Driver
Install Linux Driver
¾Linux Kernel 2.4.20 and above
¾Linux Kernel 2.6.x
Installing the Windows CE Driver
¾Installation with an installation package for Win CE 6.0
¾Installation with an installation package for Win CE 5.0
¾Removing the Moxa WinCE 5.0 / CE 6.0 Driver
¾Installation with a CAB File
¾Removing the Moxa WinCE 5.0 / CE 6.0 Driver