Moxa Technologies VPort 364A Series User manual

Moxa VPort 364A Industrial Video Encoder
User’s Manual
Edition 2.0, April 2016
www.moxa.com/product
© 2016 Moxa Inc. All rights reserved.

Moxa VPort 364A Industrial Video Encoder
User’s Manual
The software described in this manual is furnished under a license agreement and may be used only in accordance with
the terms of that agreement.
Copyright Notice
© 2016 Moxa Inc. All rights reserved.
Trademarks
The MOXA logo is a registered trademark of Moxa Inc.
All other trademarks or registered marks in this manual belong to their respective manufacturers.
Disclaimer
Information in this document is subject to change without notice and does not represent a commitment on the part of
Moxa.
Moxa provides this document as is, without warranty of any kind, either expressed or implied, including, but not limited
to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this manual, or to the
products and/or the programs described in this manual, at any time.
Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no responsibility for
its use, or for any infringements on the rights of third parties that may result from its use.
This product might include unintentional technical or typographical errors. Changes are periodically made to the
information herein to correct such errors, and these changes are incorporated into new editions of the publication.
Technical Support Contact Information
www.moxa.com/support
Moxa Americas
Toll
-free: 1-888-669-2872
Tel:
[phone]
Fax:
[phone]
Moxa China (Shanghai office)
Toll
-free: 800-820-5036
Tel:
[phone]
Fax:
[phone]
Moxa Europe
Tel:
[phone]
Fax:
[phone]
Moxa Asia
-Pacific
Tel:
[phone]
Fax:
[phone]
Moxa India
Tel:
[phone]
Fax:
[phone]

Table of Contents
1. Preliminaries..................................................................................................................................... 1-1
Before Getting Started ........................................................................................................................1-1
Important Note ..................................................................................................................................1-1
2. Introduction...................................................................................................................................... 2-1
Overview...........................................................................................................................................2-2
Package Checklist...............................................................................................................................2-3
Product Features ................................................................................................................................2-3
Typical Application..............................................................................................................................2-5
Panel Layout of the VPort 364A ............................................................................................................2-6
Product Description.............................................................................................................................2-7
3. Getting Started ................................................................................................................................. 3-1
Before Getting Started ........................................................................................................................3-2
First-Time Installation and Configuration ...............................................................................................3-2
RS-232 Console Configuration (115200, None, 8, 1, VT1 00)............................................................3-7
Mounting the VPort 364A Dimension ...................................................................................................3-11
DIN-Rail Mounting.....................................................................................................................3-12
Wall Mounting...........................................................................................................................3-12
Wiring Requirements.........................................................................................................................3-13
Grounding the VPort 364A..........................................................................................................3-13
Wiring the Redundant Power Inputs.............................................................................................3-14
Wiring the Relay Output.............................................................................................................3-14
Wiring the Digital Inputs ............................................................................................................3-15
RS-232 Connection....................................................................................................................3-15
10/100BaseT(X) Ethernet Port Connection....................................................................................3-16
100BaseFX Ethernet Port Connection...........................................................................................3-17
PTZ Port...................................................................................................................................3-18
4. Accessing the VPort 364A’s Web-based Manager.............................................................................. 4-1
Functions Featured on the VPort’s Web Homepage..................................................................................4-2
VPort’s Information .....................................................................................................................4-2
Server Name ..............................................................................................................................4-2
Camera Image View ....................................................................................................................4-2
Audio Control..............................................................................................................................4-2
Client Settings ............................................................................................................................4-3
System Configuration ..................................................................................................................4-4
Video Information .......................................................................................................................4-4
Show PTZ Control Panel ...............................................................................................................4-4
PTZ Camera Control ....................................................................................................................4-4
Custom Commands .....................................................................................................................4-5
Snapshot....................................................................................................................................4-5
Relay Control..............................................................................................................................4-5
5. System Configuration........................................................................................................................ 5-1
System Configuration by Web Console ..................................................................................................5-2
System ......................................................................................................................................5-3
Network.....................................................................................................................................5-8
DynaStreamTM...........................................................................................................................5-20
Video.......................................................................................................................................5-22
Serial Port................................................................................................................................5-27
Audio.......................................................................................................................................5-30
Alarm ......................................................................................................................................5-31
A. Frequently Asked Questions..............................................................................................................A-1
B. ModBus Address Table ...................................................................................................................... B-1
C. Settings of Supported PTZ Cameras .................................................................................................. C-1
D. Time Zone Table................................................................................................................................D-1
E. Technical Specifications .................................................................................................................... E-1

1
1. Preliminaries
Before Getting Started
Before using your VPort 364A, please pay close attention to the following instructions:

After opening the VPort 364A box, compare the contents of the box with the Package Checklist in Chapter 1. Notify
your sales representative if any of the items are missing or damaged.

To prevent damage or problems caused by improper use, read the Quick Installation Guide (the printed handbook
included in the package) before assembling and operating the device and peripherals. You may also refer to Chapter
1, under Product Description, and all of Chapter 2, of this manual.

The VPort 364A Video encoder has been designed for various environments and can be used to build various
applications for general security or demonstration purposes. For standard applications, refer Chapter 2, Getting
Started, and Chapter 3, Accessing the VPort 364A Video Encoder for the First Time.
Important Note

Surveillance devices may be prohibited by law in your country. Since VPort is both a high performance surveillance
system and networked video server, verify that the operations of such devices are legal in your locality before
installing this unit for surveillance purposes.

2
2. Introduction
The VPort 364A is a rugged networking video encoder designed for use in harsh environments. In addition to
being able to handle basic video feeds, many advanced features are also included to set up surveillance or web
multimedia applications. The VPort 364A is designed to provide stability, robustness, ease-of-use, and
flexibility.
The following topics are covered in this chapter:

Overview

Package Checklist

Product Features

Typical Application

Panel Layout of the VPort 364A

Product Description

VPort 364A Introduction
2-2
Overview
The VPort 364A is a 4-channel industrial video encoder that supports the H.264 video compression algorithm,
which provides the best video quality on the market while requiring less bandwidth compared to other video
compression standards. In addition, the VPort 364A provides dual video streams in both H.264 and MJPEG
format simultaneously. The two video streams can be independently configured to achieve an ideal video
quality and bandwidth optimization, such as different quality settings for viewing, recording, or analyzing video.
Rugged and industrial features, such as a -40 to 75°C operating temperature, IP30-rated form factor, and
industrial certifications make the VPort 364 perfect for harsh, industrial environments.
High Performance H.264/MJPEG compression
Video input can be efficiently compressed into H.264/MJPEG video stream packets in real time. This is done
without sacrificing remote monitoring capability or storage. Five levels of compression quality and four different
image resolutions provide greater versatility.
Dual video streams for meeting versatile application requirements
VPort 364A is a powerful video encoder. Aside from the high quality H.264 video compression, it can also
generate a maximum of dual video streams: one H.264 and one MJPEG simultaneously, to meet the needs of
specific applications. For example, the user can view the h.264 video streams with full D1 resolution at 30FPS
and record the MJPEG video streams with CIF resolution at 30FPS.
Moxa DynaStream™ for network efficiency
DynaSteamTM is a unique and innovative function that allows for adaptive frame rates in response to events on
the network, such as event triggers and system commands. When network traffic becomes congested,
DynaStream™ allows VPort products to respond to CGI, SNMP, and Modbus commands from SCADA and
automatically decrease video frame rates to reduce bandwidth consumption. This reserves bandwidth for the
SCADA system to maintain Quality of Service (QoS) and guarantees that the SCADA performance will not be
impacted by video traffic. For example, the frame rate can be set low during regular streaming to reduce
bandwidth usage and automatically switch to a high frame rate during triggered events to ensure quick
transmission of critical video data or video streams, or to provide detailed visual images for problem analysis.
Low video latency: under 200 ms (milliseconds)
For some mission-critical applications, low video latency is one of the key requirements. For example, highway
transportation systems monitor very fast moving vehicles; videos displayed at the central traffic control center
need to reflect the latest traffic conditions. Therefore, the video latency must be under 200ms.
2-way audio supported for a complete surveillance solution
The VPort 364A supports both audio input and audio output for voice over IP communication between a field
site and central site. The 2-way audio function not only saves time, but also saves the cost of needing to add
additional communication devices (such as a phone).
Rugged design for industrial environments
The VPort 364A is an industrial video encoder, which means that it is designed for harsh industrial
environments. With the 12/24 VDC and 24 VAC redundant power inputs, IP30 protection, and DIN-Rail
mounting, the VPort 364A meets the critical requirements of most industrial applications. Most importantly, the
VPort 364A-T can operate reliably in a -40 to 75°C temperature range. The VPort 364A-T is an optimal solution
for outdoor and harsh environments.
Modbus/TCP supported for convenient communication with SCADA/HMI
Most automation applications use SCADA/HMI systems to monitor and control field site devices and equipment.
Many SCADA/HMI systems now require real-time video for remote monitoring, and for this reason, the VPort
364A supports the Modbus/TCP protocol, which enables direct communication between the VPort and the
SCADA/HMI system, allowing administrators to easily determine the status of their VPorts for maintenance
purposes.
RTSP streaming for easy integration
RTSP (Real-time Streaming Protocol) is a client-server multimedia presentation control protocol, which enables
the interoperability of video devices and software. Hardware or software that supports RTSP streaming can

VPort 364A Introduction
2-3
easily identify and decode the video stream without the hassle of codec installation. For example, users can
view video images from the VPort 364A directly with Quick Time and VLC, both of which support RTSP
streaming.
Multicast (IGMP) transmission for network efficiency
Transmitting digital video images via an IP network requires many times the bandwidth required for
transmitting general data. For this reason, the efficiency of network bandwidth management is one of the most
important factors that determine the performance of a video over IP surveillance system. The VPort 364A
supports multicast transmission with the IGMP protocol, which can reduce the bandwidth requirements when
multiple clients access the same video stream, and greatly increases the efficiency of network bandwidth
management.
Easy web access using standard browsers
There is no need to install new software to access the video encoder, since the embedded web server allows
users to use any popular web browser to access the video encoder from anywhere over the Internet. As long
as you are connected to the network, you will be able to view the same images seen by your cameras.
Built-in 3 area-selectable Video Motion Detection (VMD)
External sensors are not required, since the video channel can be configured to detect motion in 3 areas,
making it easy to set up a security system either in your office or in the field. And the customizable settings
allow you to tune the system for both object size and sensitivity, making the video encoder adaptable to
different environments.
Weekly schedule for automated surveillance
The user-defined time period will check security settings on a weekly basis, and send notifications or drive
external devices, making the VPort 364A suitable for more versatile applications.
Flexible I/O control for external devices
2 opto-isolated sensor inputs and 2 relay outputs are provided to control external devices, giving system
integrators the option of turning an analog system into an advanced security system.
SDK support for developers
The high-performance video encoder can be integrated into many applications—without busting your
budget—and the complete programming interface of the Moxa VPort SDK PLUS makes the developer’s job easy
and straightforward. To ask about SDK requirements, please contact a Moxa sales representative for details
and an application form.
Package Checklist
The Moxa VPort 364A is shipped with the following items. If any of these items are missing or damaged, please
contact your sales representative for assistance.
•VPort 364A
•2 5-pin terminal block for 2 power inputs and 2 relay outputs
•8-pin terminal block for 4 digital inputs
•5-pin terminal block for RS-232/422/485 PTZ control port
•Quick Installation Guide
•Documentation and software CD
•Warranty statement
Note: If any of these items are missing or damaged, please contact your service representative for assistance
Product Features
High Performance Video/Audio Networking Solution
•Works with NTSC/PAL analog video cameras

VPort 364A Introduction
2-4
•Supports H.264/MJPEG video compression technologies
•Dual simultaneous video streams (1 H.264 and 1 MJPEG).
•Lower latency, under 200 ms.
•4 BNC video inputs
•Single video stream up to 30 frames/sec in Full D1 (720 x 48resolution in NTSC, and 25 frames/ sec in Full
D1 (720 x 576) resolution in PAL
•Select from Full D1/ 4CIF/ VGA/ CIF/ QCIF resolutions.
•1 audio input and 1 audio output for 2-way voice communication
•TCP, UDP, and HTTP network transmission modes
•Supports Modbus/TCP for easy communication with SCADA systems
•Standard RTSP (Real-time streaming protocol) for easy integration
•DynaStream™ for automatic frame rate adjustment
•Supports multicast (IGMP) protocols for efficient network transmission;
•DDNS, UPnP and IP filtering supported
•Supports QoS (TOS) for priority transmission
•Supports SNMP V1/V2c/V3 for network management
•Built-in web server and RS-232 console for remote access and configuration
•One auto-sensing 10/100BaseT(X) or 100BaseFX (SC connector)Ethernet port
•8 output video streams and 8 client connections.
•50 multicast clients for receiving multicast video streams
•Multicast push for all the clients
•Supports CBR (constant bit rate) or VBR (variable bit rate) encoding
•Supports 1 RS-232/RS-422/RS-485 5-pin PTZ port for controlling a PTZ (PAN/TILT/ZOOM) motorized
camera via a TCP/IP network
Rugged Industrial Design
•Two 12/24 VDC and 24 VAC redundant power inputs with LED indicators
•-40 to 75°C operating temperature for critical industrial environments (“-T”models)
•35 mm DIN-Rail mounting or panel mounting installation (requires optional accessories)
•IP30 protection form factor
•CE, FCC, and UL508 (pending) certification for industrial applications
Intelligent Alarm Trigger
•Supports system alarms, including power failure and network link
•Supports event alarms, including video motion detection (VMD),video loss, digital input, and CGI event
•Equipped with 4 DIs and 2 relays (DO) for external sensors and alarms
•Snapshot images provided for pre, trigger, and post alarm
•Sequential snapshot images supported
•Messages with snapshot images can be sent via FTP or Email
•HTTP Action setting for alarm messages sent by HTTP event server
•Capable of setting an alarm schedule
Video Management and Control
•Support for Moxa SoftNVR-IA IP surveillance software, a video recording and management solution
•Free Moxa VPORT SDK PLUS supported with flexible interface and sample code for customized applications
or system integration
NOTE
If you are interested in SoftNVR
-
IA IP surveillance software, please go to Moxa’s website www.moxa.com to
download the trial version
NOTE
If you are interested in Moxa’s VPortSDK PLUS, please go to Moxa’s website www.moxa.com to download the
package, or contact a Moxa sales representative for more information about this SDK

VPort 364A Introduction
2-5
Typical Application

VPort 364A Introduction
2-6
Panel Layout of the VPort 364A
1. RS-232 console port
2. Hardware reset button
3. 8-pin terminal block for DI 1 to DI 4
4. 5-pin terminal block for Relay 2 and power input 2 (PWR2)
5. Grounding screw
6. 5-pin terminal block for Relay 1 and power input 2 (PWR1)
7. Heat dissipation orifices
8. LEDs for STAT, PWR1, PWR2, and FAULT
9. LEDs for V1 to V4
10. AUDIO OUTPUT port for external speakers
11. AUDIO INPUT port for mic-in and line-in connection
12. 4 BNC connector for V1 to V4 video inputs
13. RJ45 10/100BaseTX Ethernet port with 10/100 Mbps LED
14. 100BaseFX fiber optic port with 100 Mbps LED
15. RS-232/422/485 PTZ port with 5-pin terminal block for PTZ
camera control
16. Model name
17. Screw hole for wall mounting
18. Screw hole for DIN-Rail mounting

VPort 364A Introduction
2-7
Product Description
BNC video input
The BNC video input is a 1Vpp, 75-ohm video port for connecting an external camera. To ensure that the
correct video modulation type is detected, the cameras should be connected and powered on before the VPort
is powered on.
NOTE
Please use a standard CCTV
cable (RG59U or above) to connect the video camera to the VPort’s BNC connector.
RCA Connectors for Audio Input/Output
The VPort 364A has 2 RCA phone jacks for audio input and output on the front panel. One jack is for a
MIC-in/Line-in audio input connection, which can be directly connected with a microphone or an audio source
from an amplifier. The other jack is a Line-out audio output connection, which can be used to connect
earphones or an amplifier.
LED indicators
The front panel of the VPort 364A contains several LED indicators. The function of each LED is described in the
table below.
LED Color State Description
STAT Green/Red Steady Red Hardware initialization stage.
Flashing Red Software initialization stage.
Steady Green System has booted up and is ready to run.
Flashing
Green Firmware is being upgraded.
PWR1 AMBER On Power is being supplied through power input PWR1.
Off Power is not being supplied through power input PWR1.
PWR2 AMBER On Power is being supplied through power input PWR2.
Off Power is not being supplied through power input PWR2.
FAULT RED On One of the following 3 conditions is met:
One of the 2 power inputs is disconnected.
Video loss.
Network disconnected.
Users can configure these alarm settings on the system
alarm page of system configuration.
Off Both power inputs are connected and are working properly,
there is no video loss and the network is connected.
V1
V2
V3
V4
GREEN On Video signal is detected
Off Video signal is not detected
10/100 AMBER On 10 Mbps link is active
Blinking Data is being transmitted at 10 Mbps
Off 10 Mbps link is inactive
GREEN On 100 Mbps link is active
Blinking Data is being transmitted at 100 Mbps
Off 100 Mbps link is inactive

VPort 364A Introduction
2-8
10/100 Mbps Ethernet port or 100 Mbps fiber optic Ethernet port
The VPort 364A series of video encoders come in three models: the VPort 364A has 1 RJ45 10/100M Ethernet
port (LEDs on the left corners of the port indicate 10M or 100M), the VPort 364A-S-SC has a single mode fiber
optic Ethernet port, and the VPort 364A-M-SC has one multi mode fiber optic Ethernet port. Choose the model
that is most appropriate for your own application.
RS-232/RS-422/RS-485 PTZ port
The VPort 364A has 1 PTZ port for PTZ control. This PTZ port is an RS-232/RS-422/485 serial port with a 5 pin
terminal block connector. The pin assignments are as follows:
PIN
RS-422/485
RS-232
1
GND
Ground
GND
Ground
2
R-
Rx-
–
N/A
3
R+
Rx+
RxD
RxD
4
T-/D-
Tx-/ Data-
---
N/A
5 T+/D+ Tx+/ Data+ TxD TxD
To enable PTZ control, users should configure the PTZ control protocol in the web console.
NOTE
The PTZ control protocol is not standardized. To use a particular PTZ control protocol, the video encoder must
support the driver for that protocol. Currently, the VPort 364
A supports PTZ control protocol drivers for:
1. Pelco D
2. Pelco P
3. Dynacolor DynaDome
4. Cohu
In addition, there is a “Transparent PTZ Control” option in the camera driver list, which is used to transmit the
PTZ control signal through the TCP/IP network
to the VPort D361 video decoder or PC (additional Real COM
driver required), and the PTZ control panel or keyboard can directly control the PTZ camera or device. There is
no need for a PTZ camera driver when using this setting.
To use a protocol that is not on the list, you will need to contact the manufacturer of the camera to get the PTZ
control commands, and then use the VPort 364A’s custom camera function to program the PTZ control.
NOTE
The VPort 364A comes with a PTZ
driver upload function for implementing new PTZ drivers. Please contact a
Moxa sales representative if you need assistance from Moxa’s R&D department to create a new PTZ driver.
Redundant 12/24 VDC and 24 VAC power inputs
The VPort 364A has two power inputs to provide redundancy. Each power input supports both 12/24 VDC and
24 VAC power for greater versatility.
NOTE
The supported power input specifications for the VPort 364A series are 12
-
32 VDC for a 12/24 VDC power input,
or 18
-30 VAC for a 24 VAC power input. The maximum power consumption is around 7.5 watts.

VPort 364A Introduction
2-9
General I/O Terminal Blocks
One 8-pin terminal block and two 5-pin terminal block are located on the VPort 364A’s top panel. The terminal
blocks provide 4 digital inputs (DI), 2 relay outputs (Relay), and 2 power inputs. The digital inputs and relay
outputs are for linking to peripheral devices, such as sensors and alarms. These I/O connections can be
employed when using the VPort 364A to create an intelligent alarm system for system operations (power failure,
video loss, disconnected network) or triggered events (VMD).
Relay Output
Normal Open Max. 1A, 24 VDC
Initial status is Normal Open
Common
Normal Close
Digital Input DI- “High”: +13V to +30V
“Low”: -30V to +3V
I1, I2 DI+
NOTE
Please refer to the VPort 364A’s Quick Installation Guide to learn how to wire the digital inputs and relay
outputs.
RS-232 Console Port
The VPort 364A has one RS-232 (10-pin RJ45) console port located on the top panel. Use either an
RJ45-to-DB9 cable or RJ45-to-DB25 cable to connect the VPort 364A’s console port to your PC’s COM port. You
may then use a console terminal program, such as Moxa PComm Terminal Emulator, to access the VPort 364A’s
console configuration utility.
Reset Button
A recessed RESET button is provided for rebooting and restoring the system to the factory default settings. Use
a pointed object, such as a straightened paper clip or toothpick, to press the reset button.
Reboot:
To reboot the VPort 364A, power it off and then power it back on again, or push the RESET button one time. The
STAT LED will light in red as the POST (Power On Self Test) process runs. When the rebooting process is
finished, the STAT LED will turn green.
Restore to Factory Settings:
A recessed RESET button is provided for restoring the system to the factory default settings. When the system
fails to install properly, or operates abnormally, use the RESET button located on the top panel of the VPort
364A to restore the factory defaults.
To do this, use a pointed object such as a straightened paper clip or toothpick to hold down the reset button,
and then release the reset button when the STAT LED stops flashing in red. At this point, the POST process will
run, and the VPort will reboot. The STAT LED will turn green when the VPort has finished rebooting.

3
3. Getting Started
This chapter includes information about how to install a VPort 364A video encoder.
The following topics are covered in this chapter:

Before Getting Started

First-Time Installation and Configuration
RS-232 Console Configuration (115200, None, 8, 1, VT1 00)

Mounting the VPort 364A Dimension
DIN-Rail Mounting
Wall Mounting

Wiring Requirements
Grounding the VPort 364A
Wiring the Redundant Power Inputs
Wiring the Relay Output
Wiring the Digital Inputs
RS-232 Connection
10/100BaseT(X) Ethernet Port Connection
100BaseFX Ethernet Port Connection
PTZ Port

VPort 364A Getting Started
3-2
Before Getting Started
In what follows, “user” refers to those who can access the video encoder, and “administrator” refers to the
person who knows the root password that allows changes to the Video Encoder’s configuration, in addition to
providing general access. Administrators should read this part of the manual carefully, especially during
installation.
First-Time Installation and Configuration
Before installing the VPort 364A, check to make sure that all the items on the package checklist are in the box.
In addition, you will need access to a notebook computer or PC equipped with an Ethernet port.
Step 1: Select the power source
The VPort 364A can be powered by a 12 to 32 VDC DC power input, or a 18 to 30 VAC AC power input. Two
power inputs are provided for redundancy. Users can check the LED status located in the front panel to see if
the power inputs are connected appropriately. If one of the power inputs fails, the FAULT LED will light up in red
if the power failure alarm is enabled.
NOTE
The VPort 364A series support power input specifications of 12
-32 VDC for 12/24 VDC power input, or 18-
30
VAC for 24 VAC power input (note that this is different from Moxa EDS switch’s 12
-
45 VDC power input). The
maximum
power consumption is around 7.5 watts.
Step 2: Connect the VPort 364A to a Network
The VPort 364A has one auto-sensing 10/100 Mbps RJ45 Ethernet port, or one 100 Mbps fiber optic ports (multi
mode or single mode) for network connectivity. Both the RJ45 and fiber optic ports have separate LEDs for 10
Mbps and 100 Mbps connections.
Step 3: Connect the VPort 364A to a camera and an audio source
The VPort 364A has 4 VIDEO INPUT ports. Use the BNC connector (1.0 Vpp, 75Ω) and coaxial cable to connect
video cameras to the VPort to input analog video signals.
The VPort 364A has 1 audio input and 1 audio output. A microphone or an amplifier can be plugged directly into
the AUDIO INPUT port, and a speaker can be plugged into the AUDIO OUTPUT port.
NOTE
Four VIDE
O LEDs (V1, V2, V3, V4) are located on the VPort 364A’s front panel to indicate the video signal
transmission status for video inputs. Check the LED status to see if the video is working properly.
Step 4: Connecting motorized PTZ cameras
The VPort 364A has one RS-232/422/485 PTZ port with a 5-pin terminal block connector for connecting PTZ
control cables to control PTZ cameras over a TCP/IP network.
To enable PTZ control, users should configure the PTZ control protocol in the web-based manager.

VPort 364A Getting Started
3-3
NOTE
The PTZ control protocol is not standardized. To use a particular PTZ control protocol, the video server must
support the driver for that protocol. Currently, the VPort 364A supports PTZ control protocol drivers for:
1. Pelco D
2. Pelco P
3. DynaColor DynaDome
4. Cohu
If you need to use a protocol that is not on the list, contact the manufacturer of the camera to get the PTZ
control commands, and then program its PTZ control using the VPort 364A’s Custom Camera function.
NOTE
The VPort 364A comes with a PTZ driver upload function for implementing new PTZ drivers. Please contact a
Moxa sales representative if you need assistance from Moxa’s R&D department to create a new PTZ driver.
NOTE
The “Transparent PTZ Control” function in the camera driver list is used to transmit the PTZ control signal over
a TCP/IP network to the VPort D361 video decoder or PC (additional driver required). The PTZ control panel or
keyboard can directly control the PTZ camera or device, eliminating the need for a PTZ camera driver and
allo
wing the use of PTZ cameras with the VPort encoder.
Step 5: Configure the VPort 364A’s IP address
After powering on the VPort 364A, wait a few seconds for the POST (Power On Self Test) to run. The STAT LED
turns green to indicate that the POST process has completed. The IP address will be assigned when the 10 or

VPort 364A Getting Started
3-4
100 Mbps NETWORK LED blinks. The IP address assigned after the POST is completed depends on the network
environment.
Network Environment with a DHCP Server
In this case, the IP address of the VPort 364A is assigned by a DHCP Server. Use the DHCP Server’s IP address
table, or use the Moxa VPort utility to determine the IP address that was assigned by the DHCP Server.
NOTE
After powering on the VPort 364A, wait a few seconds for the POST (Power On Self Test) to run. The IP address
will be assigned when the 10 or 100 Mbps NETWORK LED blinks.
Using the Moxa Ethernet Switch And Video Server Configuration Utility (edscfgui.exe), as described
below:
1. Run the edscfgui.exe program to search for the VPort and EDS switches. After the Utility window opens,
you may also select or click on Broadcast Search, which is located under the List Server menu, to initiate a
search (note that you can also click on the Broadcast Search icon to initiate a search.
NOTE
You may download the Moxa Ethernet Switch And Video Server Configuration Utility (edscfgui.exe) software
from Moxa’s website at www.moxa.com.
2. The Broadcast Search window will show a list of all switches and VPort located on the network. The
progress of the search will also be displayed.

VPort 364A Getting Started
3-5
3. When the search has ended, the Model Name, MAC address, and IP address of the EDS Switch and the VPort
will be listed in the Utility window.
NOTE
Broadcast Search can only be used to search for devices on the same LAN domain. If your devices are located
on a different LAN domain, use Specify IP Address to search for the device by inputting the IP address.
4. Double-click the selected VPort, or use Internet Explorer to access the VPort’s web-based manager (web
console).
Network Environment without a DHCP Server:
If your VPort 364A is connected to a network that does not have a DHCP server, then you will need to configure
the IP address manually. The default IP address of the VPort 364A is 192.168.127.100 and the default subnet
mask is 255.255.255.0. Note that you may need to change your computer’s IP address and subnet mask so
that the computer is on the same subnet as the VPort.
To change the IP address of the VPort manually, access the VPort’s web server, and then navigate to the
System Configuration

Network

General page to configure the IP address and other network settings.
Check the Use fixed IP address box to ensure that the IP address you assign is not deleted each time the
VPort is restarted.
Step 6: Log into the ActiveX Control Plug-in
Type the IP address in the web browser’s address input box and then press enter.
Step 7: Install the ActiveX Control plug-in
A security warning message will appear the first time you access the VPort’s web-based manager. The message
is related to installing the VPort ActiveX Control component to your PC or notebook. Click on Yes to install this
plug-in to enable the IE web browser for viewing video images.

VPort 364A Getting Started
3-6
NOTE
For Windows XP SP2 or above operating systems, the ActiveX Control component will be blocked for system
security reasons. In this case, the VPort’s security warning message window may not appear. Users should
unblock the ActiveX control function or disable the security configuration to enable the installation of VPort’s
ActiveX Control component.
Step 8: Accessing the homepage of the VPort 364A’s web-based manager.
After installing the ActiveX Control component, the homepage of the VPort 364A’s web-based manager will
appear. Check the following items to make sure the system was installed properly:
1. Video Images
2. Audio (make sure your PC’s or notebook’s sound is turned on)
3. Video Information
Step 9: Accessing the VPort’s System Configuration
Click on System Configuration to access the overview of the system or to change the settings. Model Name,
Server Name, IP Address, MAC Address, Firmware Version, and LED Status appear in the green bar near the
top of the page. Use this information to check the system information and installation.

VPort 364A Getting Started
3-7
For details of each configuration, check the User’s Manual on the software CD.
NOTE
After accessing the VPort 364A’s web
-based manager, administrators should access System Configuration

System 
Account to set up the administrator’s password and enable the authentication function. The
administrator account name is
admin.
An authentication window will pop up requesting the account name and password each time the VPort 364A is
accessed.
RS-232 Console Configuration (115200, None, 8, 1, VT1 00)
NOTE
1. You cannot connect to the VPort 364A simultaneously by serial console and Telnet.
2. You may
connect to the VPort 364A simultaneously by web browser and serial console, or by web browser
and Telnet. However, we
strongly recommend that you use only one connection method at a time. This
allows you to maintain better control over your VPort 364A’s configuration.
You can access the RS-232 console by using a terminal emulator on your PC. We recommend that you use the
PComm Terminal Emulator, which is free and can be downloaded from Moxa’s website. The following
instructions explain how to use PComm to access the RS-232 console.
1. Use an RJ45 to DB9-F (or RJ45 to DB25-F) cable to connect the VPort 364’s RS-232 console port to a COM
port on your PC.