Moxa Technologies 1802001142326 User manual

P/N: 1802001142326
*1802001142326*
Universal PCI Smart Serial
Board
Quick Installation Guide
Version 1.1, December 2019
Technical Support Contact Information
www.moxa.com/support
Moxa Americas:
Toll
-free: 1-888-669-2872
Tel:
1-714-528-6777
Fax:
1-714-528-6778
Moxa China (Shanghai office):
Toll
-free: 800-820-5036
Tel:
[phone]
Fax:
[phone]
Moxa Europe:
Tel:
[phone]
Fax:
[phone]
Moxa Asia-Pacific:
Tel:
[phone]
Fax:
[phone]
Moxa India:
Tel:
[phone]
Fax:
[phone]

2019 Moxa Inc. All rights reserved.

- 2 -
Overview
Moxa’s Universal PCI (UPCI) multiport serial boards can be installed in
PCI or PCI-X slots and support both 3.3V and 5V PCI/PCI-X.
Package Checklist
UPCI board are shipped with the following items:
•1 Moxa UPCI multiport serial board
•Low-profile bracket (low-profile models only)
•Quick installation guide (printed)
•Warranty card
NOTE
Notify your sales representative if any of the above items are
missing or damaged.
Hardware Installation Procedure
The Universal PCI board MUST be plugged into the PC before the driver
is installed.
Follow the steps below:
1. Select serial transmission mode. This step is for certain models
listed below. If your product on hand is not included, please directly
go to step2.
If your model is CP-112UL Series/CP-114UL Series/CP-118U Series/
CP-132UL Series/CP-134U Series/CP-138U Series, you will need to
set onboard DIP switches for each port.
(Refer to “Dip Switch Settings” section to complete the DIP
switches setting)
2. Install the board. Power off the PC and then plug the board firmly
into any open PCI or PCI-X expansion slot.
3. Plug the connection cable into the board’s connector. (Refer
to “Pin Assignments” section for the cable pin assignment).
4. Start system and verify the driver initialization.
Software Installation Information
1. Get the driver at www.moxa.com.Based on the OS type,
choose the corresponding driver.
2. Installing the driver:
•For Windows OS (Take the installation of Win7 as an
example)
2.1. Unzip and execute the .exe file
2.2. Follow the instructions to install the drivers
•For Linux
Execute the following commands from the Linux prompt:
2.1. Get the driver at www.moxa.com and unzip the file:
#cd /
#mkdir moxa
#cd moxa
#cp /<driver
directory>/driv_linux_smart_<version>_build_<build_date
>.tgz .

- 3 -
#tar -zxvf
driv_linux_smart_<version>_build_<build_date>.tgz
2.2. Install the driver:
#cd mxser
#./mxinstall
2.3. Verify the driver status
Use the Moxa diagnostic utility to verify the driver status:
#cd /moxa/mxser/utility/diag
#./msdiag
2.4. Test the tty port
Use the Moxa terminal utility to test the tty ports:
#cd /moxa/mxser/utility/term
#./msterm
DIP Switch Settings
CP-112UL Series/CP-112UL-I Series
Mode
S1
S2
S3
RS-232
ON
–
–
RS-422
OFF
ON
–
4-Wire RS-485
OFF
OFF
ON
2-Wire RS-485
OFF
OFF
OFF
CP-114UL Series/CP-114UL-I Series
Mode
S1
S2
S3
RS-232
–
–
ON
RS-422
–
ON
OFF
4-Wire RS-485
ON
OFF
OFF
2-Wire RS-485
OFF
OFF
OFF
CP-118U Series/CP-118U-I Series
Mode
S1
S2
S3
RS-232
–
–
ON
RS-422
–
ON
OFF
4-Wire RS-485
ON
OFF
OFF
2-Wire RS-485
OFF
OFF
OFF
CP-132UL Series
Mode
S1
S2
Illustration
RS-422
–
OFF
2-Wire RS-485
ON
ON
4-Wire RS-485
OFF
ON

- 4 -
CP-134U Series/CP-134U-I Series
RS-422 or RS-485 mode:
Use the jumper to cover the two
columns
on the left of the jumper
pins.
RS-232 mode: Use the jumper to
cover the two columns o
n the right
of the jumper pins.
CP-138U Series/CP-138U-I Series
Mode
S1
S2
RS-422
–
ON
4-Wire RS-485
ON
OFF
2-Wire RS-485
OFF
OFF
Pin Assignments
CP-102U Series
Male DB9 RS-232
Pin
Signal
1
DCD
2
RxD
3
TxD
4
DTR
5
GND
6
DSR
7
RTS
8
CTS

- 5 -
CP-102UL Series
Female DB25 RS-232
Pin
Signal
Pin
Signal
1
–
14
–
2
DCD1
15
DTR1
3
GND
16
DSR1
4
CTS1
17
RTS1
5
RxD1
18
TxD1
6
–
19
–
7
–
20
–
8
–
21
DCD0
9
DTR0
22
GND
10
DSR0
23
CTS0
11
RTS0
24
RxD0
12
TxD0
25
–
13
–
–
–
CP-104JU Series
RJ45 (RS-232)
Pin
Signal
1
DSR
2
RTS
3
GND
4
TxD
5
RxD
6
DCD
7
CTS
8
CTR
CP-104UL
Male DB25 (CBL-M44M25x4-50)
Pin
Signal
2
TxD
3
RxD
4
RTS
5
CTS
6
DSR
7
GND
8
DCD
20
DTR

- 6 -
(CBL-M44M9x4-50)
(OPT4-M9A)
Pin
Signal
1
DCD
2
RxD
3
TxD
4
DTR
5
GND
6
DSR
7
RTS
8
CTS
Male DB9
RJ45 (OPT4-RJ45A)
Pin
Signal
1
DSR
2
RTS
3
GND
4
TxD
5
RxD
6
DCD
7
CTS
8
DTR
8-pin RJ45
CP-112UL Series
Male DB9 (CBL-M25M9x2-50)
Pin
RS-
232
RS-422/
RS-485-
4W
RS-485-
2W
1
DCD
TxD-(A)
–
2
RxD
TxD+(B)
–
3
TxD
RxD+(B)
Data+(B)
4
DTR
RxD-(A)
Data-(A)
5
GND
GND
GND
6
DSR
–
–
7
RTS
–
–
8
CTS
–
–
9
–
–
–
CP-114UL Series
Male DB9 (CBL-M44M9x4-50)
Pin
RS-
232
RS-422/
RS-485-
4W
RS-485-
2W
1
DCD
TxD-(A)
–
2
RxD
TxD+(B)
–
3
TxD
RxD+(B)
Data+(B)
4
DTR
RxD-(A)
Data-(A)
5
GND
GND
GND
6
DSR
–
–
7
RTS
–
–
8
CTS
–
–
9
–
–
–

- 7 -
Male DB25 (CBL-M44M25x4-50)
Pin
RS-232
RS-422/
RS-485-4W
RS-485-2W
2
TxD
RxD+(B)
Data+(B)
3
RxD
TxD+(B)
–
4
RTS
–
–
5
CTS
–
–
6
DSR
–
–
7
GND
GND
GND
8
DCD
TxD-(A)
–
20
DTR
RxD-(A)
Data-(A)
CP-118UI Series/CP-138U-I Series
Male DB9 (CBL-M78M9x8-100)
Pin
RS-
232
RS-422/
RS-485-
4W
RS-485-
2W
1
DCD
TxD-(A)
–
2
RxD
TxD+(B)
–
3
TxD
RxD+(B)
Data+(B)
4
DTR
RxD-(A)
Data-(A)
5
GND
GND
GND
6
DSR
–
–
7
RTS
–
–
8
CTS
–
–
9
–
–
–
*CP-118U-I Series only
Male DB25 (CBL-M78M25x8-100)
Pin
RS-232
RS-422/
RS-485-4W
RS-485-2W
2
TxD
RxD+(B)
Data+(B)
3
RxD
TxD+(B)
–
4
RTS
–
–
5
CTS
–
–
6
DSR
–
–
7
GND
GND
GND
8
DCD
TxD-(A)
–
20
DTR
RxD-(A)
Data-(A)
*CP-118U-I Series only

- 8 -
CP-118U Series/CP-138U Series
Male DB9
(CBL-M62M9x8-100, OPT8-M9 is for CP-118U and CP-138U)
(CBL-M78M9x8-100 is for CP-118U-I and CP-138U-I)
Pin
RS-
232
RS-422/
RS-485-
4W
RS-485-
2W
1
DCD
TxD-(A)
–
2
RxD
TxD+(B)
–
3
TxD
RxD+(B)
Data+(B)
4
DTR
RxD-(A)
Data-(A)
5
GND
GND
GND
6
DSR
–
–
7
RTS
–
–
8
CTS
–
–
9
–
–
–
Male DB25
(CBL-M62M25x8-100, OPT8B is for CP-118U and CP-138U)
(CBL-M78M25x8-100 is for CP-118U-I and CP-138U-I)
Pin
RS-232
RS-422/
RS-485-4W
RS-485-2W
2
TxD
RxD+(B)
Data+(B)
3
RxD
TxD+(B)
–
4
RTS
–
–
5
CTS
–
–
6
DSR
–
–
7
GND
GND
GND
8
DCD
TxD-(A)
–
20
DTR
RxD-(A)
Data-(A)
Female DB25 (OPT8A/S)
Pin
RS-232
RS-422/
RS-485-4W
RS-485-2W
2
RxD
TxD+(B)
–
3
TxD
RxD+(B)
Data+(B)
4
CTS
–
–
5
RTS
–
–
6
DTR
RxD-(A)
Data-(A)
7
GND
GND
GND
8
DCD
TxD-(A)
–
20
DSR
–
–
*CP-118U Series only

- 9 -
RJ45 (OPT8-RJ45)
Pin
Signal
1
DSR
2
RTS
3
GND
4
TxD
5
RxD
6
DCD
7
CTS
8
DTR
*CP-118U Series only
CP-132UL Series/CP-132UL-I Series
Male DB9 Connector: Device-side Pin Assignments
Pin
RS-232
RS-422/
RS-485-4W
RS-485-2W
1
TxD-(A)
TxD-(A)
–
2
TxD+(B)
TxD+(B)
–
3
RxD+(B)
RxD+(B)
Data+(B)
4
RxD-(A)
RxD-(A)
Data-(A)
5
GND
RxD-(A)
GND
6
RTS-(A)
GND
–
7
RTS+(B)
–
–
8
CTS+(B)
–
–
9
CTS-(A)
–
–
CP-134U Series
Male DB9 (CBL-M44M9x4-50)
Pin
RS-232
RS-422
RS-485-
4W
RS-485-
2W
1
DCD
TxD-(A)
TxD-(A)
–
2
RxD
TxD+(B)
TxD+(B)
–
3
TxD
RxD+(B)
RxD+(B)
Data+(B)
4
DTR
RxD-(A)
RxD-(A)
Data– (A)
5
GND
GND
GND
GND
6
DSR
RTS-(A)
–
–
7
RTS
RTS+(B)
–
–
8
CTS
CTS+(B)
–
–
9
–
CTS-(A)
–
–
Male DB25 (CBL-M44M25x4-50)
Pin
RS-232
RS-422
RS-485-
4W
RS-485-
2W
2
TxD
RxD+(B)
RxD+(B)
Data+(B)
3
RxD
TxD+(B)
TxD+(B)
–
4
RTS
RTS+(B)
–
–
5
CTS
CTS+(B)
–
–
6
DSR
RTS-(A)
–
–
7
GND
GND
GND
GND
8
DCD
TxD-(A)
TxD-(A)
–
20
DTR
RxD-(A)
RxD-(A)
Data-(A)
22
–
CTS-(A)
–
–

- 10 -
CP-168U Series
RS-232 Cable Wiring for OPT8A/B/C/D/S
OPT8A/S (DCE, DB25 Female)
Pin
Signal
2
RxD
3
TxD
4
CTS
5
RTS
6
DTR
7
GND
8
DCD
20
DSR
OPT8-RJ45 (8-pin)
Pin
Signal
1
DSR
2
RTS
3
TxD
4
GND
5
RxD
6
DCD
7
CTS
8
DTR
OPT8B/C (DCE, DB25 Male)
Pin
Signal
2
TxD
3
RxD
4
RTS
5
CTS
6
DSR
7
GND
8
DCD
20
DTR
OPT8-M9, OPT8D (DTE, DB9 Male)
Pin
Signal
1
DCD
2
RxD
3
TxD
4
DTR
5
GND
6
DSR
7
RTS
8
CTS