Moxa Technologies CP-134EL-A-I User manual

P/N: 1802001182045
*1802001182045*
PCI Express Multiport
Serial Board Series
Quick Installation Guide
Version 2.4, January 2023
Technical Support Contact Information
www.moxa.com/support
2022 Moxa Inc. All rights reserved.

- 2 -
Overview
Moxa’s new PCI Express Multiport Serial Boards series is designed for
POS and ATM applications and for use by industrial automation system
manufacturers and system integrators.
Package Checklist
Before installing the PCI Express board, verify that the package
contains the following items:
•1 MOXA multiport serial board (1 PCI Express board or 1 PCI
Express-A Intelligent board)
•Low-profile bracket (low profile models only)
•Quick installation guide (printed)
•Warranty card
NOTE
Notify your sales representative if any of the above items are
missing or damaged.
Hardware Installation Procedure
The PCI Express board MUST be plugged into the PC before the driver is
installed.
Follow the steps below.
1. Install the board. Power off the PC and then plug the board
firmly into any open PCI Express slot.
2. Plug the connection cable into the board’s connector. (Refer
to Pin Assignments for the cable pin assignment).
3. Start system and verify the driver initialization.
Software Installation Information
1. Get the driver at www.moxa.com.Base on the OS type,
choosing the corresponding driver.
2. Installing the driver:
•For Windows OS (Take the installation of Win7 as an
example)
2.1. Unzip and execute the .exe file
2.2. Follow the instructions to install the drivers
•For Linux
Execute the following commands from the Linux prompt:
2.1. Get the driver at www.moxa.com and unzip the file:
#cd /
#mkdir moxa
#cd moxa
#cp /<driver
directory>/driv_linux_smart_<version>_build_<build_dat
e>.tgz.
#tar -zxvf
driv_linux_smart_<version>_build_<build_date>.tgz
2.2. Install the driver:
#cd mxser
#./mxinstall

- 3 -
2.3. Verify the driver status
Use the Moxa diagnostic utility to verify the driver status:
#cd /moxa/mxser/utility/diag
#./msdiag
2.4. Test the tty port
Use the Moxa terminal utility to test the tty ports:
#cd /moxa/mxser/utility/term
#./msterm
3. Intelligent RS-485
The following models support the intelligent RS-485 feature:
•CP-134EL-A-I without a cable
•CP-134EL-A-I-DB9M
•CP-134EL-A-I-DB25M
•CP-138E-A-I without a cable
•CP-118E-A-I without a cable
•CP-116E-A without a cable
If your multiport serial board is one of the above models, and has
an RS-485 2W interface, then you could follow the sections below
to complete the intelligent RS-485 setting.
NOTE
The other PCIe multiport serial boards don't support the
intelligent RS-485 feature.
•For Windows OS
3.1. Go to the device management to complete the model
properties setting.
3.2. Click Start Diagnosis. (It should be RS-485-2W).
If the status is OK, nothing further needs to be done.
If the status is Waveform Distortion, Data Error, or
Receive Reflect Signal, go to next step to do the auto
tuning
3.3. Auto Tuning
Still in the Properties Settings page, click on the COM
number that shows the error message.
Click Auto Tuning.
Click OK to apply the setting change for the bias resistor
and termination resistor.
•For Linux
Follow these steps to configure the Intelligent RS-485 in Linux
3.1. Detect the configurations of the port by the following
command:
#./muestty -g /dev/ttyMUE1#cd /
3.2.Use the following command to run diagnosis to see if
the setting is correct.
#./muestty -d /dev/ttyMUE1
3.3. If the alarm status shows OK, nothing further needs
to be done. If the alarm status shows Fail, then there are
problems with the setting. Do the auto-tuning process
with the following command
#./muestty -a /dev/ttyMUE1

- 4 -
3.4. Manually configure the Pull Up/Down resistor and the
terminator resistor with the assigned values:
#./muestty –p (assigned value) /dev/ttyMUE1
#./muestty –t (assigned value) /dev/ttyMUE1
3.5. Do the diagnosis again:
#./muestty -d /dev/ttyMUE1
Pin Assignments
CP-102E / CP-102EL
Male DB9 (CBL-M25M9x2-50 for CP-102EL)
Pin
RS-232
1
DCD
2
RxD
3
TxD
4
DTR
5
GND
6
DSR
7
RTS
8
CTS
DB9 male
CP-132EL/CP-132EL-I
Male DB9 (Device side)
Pin
RS-422/
RS-485-4W
RS-485-2W
1
TxD-(A)
–
2
TxD+(B)
–
3
RxD+(B)
Data+(B)
4
RxD-(A)
Data-(A)
5
GND
GND
6
–
–
7
–
–
8
–
–
DB9 male
CP-114EL/CP-114EL-I
Male DB9 (CBL-M44M9x4-50)
Pin RS-232
RS-422/
RS-485-4W
RS-485-2W
1
DCD
TxD-(A)
–
2
RxD
TxD+(B)
–
3
TxD
RxD+(B)
Data+(B)
4
DTR
RxD-(A)
Data-(A)
5
GND
GND
GND
6
DSR
–
–
7
RTS
–
–
8
-
–
–
DB9 male

- 5 -
Male DB25 (CBL-M44M25x4-50)
Pin RS-232
RS-422/
RS-485-4W
RS-485-2W
2
TxD
RxD+(B)
Data+(B)
3
RxD
TxD+(B)
–
4
RTS
–
–
5
CTS
–
–
6
DSR
–
–
7
GND
GND
GND
8
DCD
TxD-(A)
–
20
DTR
RxD-(A)
Data-(A)
DB25 male
CP-118E-A-I / CP-138E-A-I
Male DB9 (CBL-M78M9x8-100)
Pin RS-232 RS-422/
RS-485-4W
RS-485-2W
1
DCD
TxD-(A)
–
2
RxD
TxD+(B)
–
3
TxD
RxD+(B)
Data+(B)
4
DTR
RxD-(A)
Data-(A)
5
GND
GND
GND
6
DSR
–
–
7
RTS
–
–
8
CTS
–
–
DB9 male
Male DB25 (CBL-M78M25x8-100)
Pin RS-232
RS-422/
RS-485-4W
RS-485-2W
2
TxD
RxD+(B)
Data+(B)
3
RxD
TxD+(B)
–
4
RTS
–
–
5
CTS
–
–
6
DSR
–
–
7
GND
GND
GND
8
DCD
TxD-(A)
–
20
DTR
RxD-(A)
Data-(A)
DB25 male
CP-134EL-A-I
Male DB9 (CBL-M44M9x4-50)
Pin RS-232
RS-422/
RS-485-4W
RS-485-2W
1
DCD
TxD-(A)
–
2
RxD
TxD+(B)
–
3
TxD
RxD+(B)
Data+(B)
4
DTR
RxD-(A)
Data-(A)
5
GND
GND
GND
6
DSR
–
–
7
RTS
–
–
8
CTS
–
–
DB9 male

- 6 -
Male DB25 (CBL-M44M25x4-50)
Pin RS-232
RS-422/
RS-485-4W
RS-485-2W
2
TxD
RxD+(B)
Data+(B)
3
RxD
TxD+(B)
–
4
RTS
–
–
5
CTS
–
–
6
DSR
–
–
7
GND
GND
GND
8
DCD
TxD-(A)
–
20
DTR
RxD-(A)
Data-(A)
DB25 male
CP-116E-A
Male DB9 (OPT8-M9+ / CBL-M68M9x8-100)
Pin RS-232 RS-422/
RS-485-4W
RS-485-2W
1
DCD
TxD-(A)
–
2
RxD
TxD+(B)
–
3
TxD
RxD+(B)
Data+(B)
4
DTR
RxD-(A)
Data-(A)
5
GND
GND
GND
6
DSR
–
–
7
RTS
–
–
8
CTS
–
–
DB9 male
Male DB25 ( OPT8B+ / CBL-M68M25x8-100)
Pin RS-232
RS-422/
RS-485-4W
RS-485-2W
2
TxD
RxD+(B)
Data+(B)
3
RxD
TxD+(B)
–
4
RTS
–
–
5
CTS
–
–
6
DSR
–
–
7
GND
GND
GND
8
DCD
TxD-(A)
–
20
DTR
RxD-(A)
Data-(A)
DB25 male
Female DB25 (OPT8A+/S+)
Pin RS-232
RS-422/
RS-485-4W
RS-485-2W
2
RxD
TxD+(B)
–
3
TxD
RxD+(B)
Data+(B)
4
CTS
–
–
5
RTS
–
–
6
DTR
RxD-(A)
Data-(A)
7
GND
GND
GND
8
DCD
TxD-(A)
–
20
DSR
–
–
DB25 female

- 7 -
사용자안내문
이
기기는 업무용 환경에서 사용할 목적으로 적합성 평가를 받은 기기로서
가정용
환경에서 사용하는 경우 전파간섭의 우려가 있습니다.
사용자안내문 (User Guide)
이기기는 업무용 환경에서 사용할 목적으로 적합성평가를 받은
기기로서가정용 환경에서 사용하는 경우 전파간섭의 우려가 있습니다.
(This equipment has KC approval for use in industrial environments and
could possibly interfere with household equipment.)
기종별
Type of Equipment
사용자안내문
User Guide
A 급기기 (업무용 방송 통신기
자재)
Class A Equipment
(Broadcasting and
Communication Equipment for
Industrial and Commercial Use)
이기기는 업무용 (A 급)전자파 적합
기기로서 판매자 또는 사용자는 이
점을 주의하시기 바라며 가정 외의
지역에서 사용하는 것을 목적으로
합니다.
This equipment is the EMC conformity
equipment (Class A) for I
ndustrial and
Commercial Use. The seller or user
should take note of this as this
equipment can be used in places that
exclude homes.