Moxa Technologies CN2610 series User manual

CN2610 Dual-LAN Async Server
User’s Manual
Fourth Edition, July 2007
www.moxa.com/product
Moxa Technologies Co., Ltd.
Tel: [phone]
Fax: [phone]
Web: www.moxa.com
MOXA Technical Support
Worldwide: [e-mail]
The Americas: [e-mail]

CN2610 Dual-LAN Async Server
User’s Manual
The software described in this manual is furnished under a license agreement and may be used only in
accordance with the terms of that agreement.
Copyright Notice
Copyright ©2007 Moxa Technologies Co., Ltd.
All rights reserved.
Reproduction without permission is prohibited.
Trademarks
MOXA is a registered trademark of the Moxa Group.
All other trademarks or registered marks in this manual belong to their respective manufacturers.
Disclaimer
Information in this document is subject to change without notice and does not represent a commitment on the
part of MOXA.
MOXA provides this document “as is,” without warranty of any kind, either expressed or implied, including, but
not limited to, its particular purpose. MOXA reserves the right to make improvements and/or changes to this
manual, or to the products and/or the programs described in this manual, at any time.
Information provided in this manual is intended to be accurate and reliable. However, MOXA assumes no
responsibility for its use, or for any infringements on the rights of third parties that may result from its use.
This product might include unintentional technical or typographical errors. Changes are periodically made to the
information herein to correct such errors, and these changes are incorporated into new editions of the
publication.

Table of Contents
Chapter 1 Introduction..............................................................................................1-1
Product Features................................................................................................................. 1-2
Hardware................................................................................................................. 1-2
Software.................................................................................................................. 1-2
Package Checklist .............................................................................................................. 1-2
Front Panel......................................................................................................................... 1-3
Rear Panel .......................................................................................................................... 1-3
Bottom Label...................................................................................................................... 1-3
Chapter 2 Getting Started.........................................................................................2-1
Hardware Installation......................................................................................................... 2-2
Desktop................................................................................................................... 2-2
Rackmount.............................................................................................................. 2-2
Wiring Requirements.............................................................................................. 2-3
Connecting the CN2610-8/16’s Power ................................................................... 2-3
Connecting to the Network ..................................................................................... 2-3
Connecting to a Serial Device................................................................................. 2-4
Connecting to the Console Port............................................................................... 2-4
Accessing the Console Utility............................................................................................ 2-4
Configuration Checklist.......................................................................................... 2-4
Accessing the Console from a Telnet Terminal...................................................... 2-4
Accessing the Console from a Console Terminal................................................... 2-7
Configuring the CN2610—The Server Menu.................................................................. 2-13
Server Configuration—Info.................................................................................. 2-13
Server Configuration—LAN................................................................................. 2-14
Server Configuration—Adv.................................................................................. 2-16
Server Configuration—Host_table........................................................................ 2-17
Server Configuration—Route_table...................................................................... 2-18
Server Configuration—User_table........................................................................ 2-19
Save.................................................................................................................................. 2-20
Restart .............................................................................................................................. 2-20
Chapter 3 Knowing Your Application......................................................................3-1
Windows Real COM (NT Real COM)............................................................................... 3-2
Linux Real TTY/Unix Fixed TTY (NT Real COM)........................................................... 3-3
Device Control (Device Control)....................................................................................... 3-3
UDP Communication (Raw UDP) ..................................................................................... 3-4
Dual-host Redundant DataAcquisition System (DRDAS)................................................ 3-5
Redundant COM ................................................................................................................ 3-7
Console Management (Reverse Terminal) ......................................................................... 3-8
Terminal Access (Terminal) ............................................................................................... 3-9
Multi-host TTY (Multi-host TTY) ................................................................................... 3-10
Dial-in/Out-of-Band Management (Dialin/out).................................................................3-11
Network Printer (Printer) ................................................................................................. 3-12
Multiplexor Access (Multiplex) ....................................................................................... 3-13
Chapter 4 Setting Up Windows Real COM/Linux Real TTY/Unix Fixed TTY........4-1
Accessing the Console Utility............................................................................................ 4-2
Selecting theApplication ................................................................................................... 4-3

Configuring ASPP Mode.................................................................................................... 4-4
Configuring the Serial Ports............................................................................................... 4-5
Save.................................................................................................................................... 4-6
Restart ................................................................................................................................ 4-7
Setting up Hosts ................................................................................................................. 4-7
Setting up Windows XP/2003 Hosts....................................................................... 4-7
Setting up Windows 2000 Hosts........................................................................... 4-25
Setting up Windows 95/98/ME/NT Hosts ............................................................ 4-38
Chapter 5 Setting Up Device Control......................................................................5-1
Accessing the Console Utility............................................................................................ 5-2
Selecting theApplication ................................................................................................... 5-3
Configuring ASPP Mode.................................................................................................... 5-4
Configuring RAW Mode.................................................................................................... 5-6
Configuring the Serial Ports............................................................................................... 5-8
Save.................................................................................................................................... 5-9
Restart ................................................................................................................................ 5-9
ASPP Library Introduction............................................................................................... 5-10
ASPP Examples for Unix................................................................................................. 5-10
ASPP Examples for Windows...........................................................................................5-11
Chapter 6 Setting Up Raw UDP................................................................................6-1
Accessing the Console Utility............................................................................................ 6-2
Selecting theApplication ................................................................................................... 6-3
Configuring RAW UDP Mode ........................................................................................... 6-4
Configuring the Serial Ports............................................................................................... 6-6
Save.................................................................................................................................... 6-7
Restart ................................................................................................................................ 6-7
Chapter 7 Setting Up the Dual-host Redundant Data Acquisition System..........7-1
Accessing the Console Utility............................................................................................ 7-2
Selecting theApplication ................................................................................................... 7-3
Configuring DRDAS Mode................................................................................................ 7-4
Configuring the Serial Ports............................................................................................... 7-5
Save.................................................................................................................................... 7-7
Restart ................................................................................................................................ 7-7
Chapter 8 Setting Up Redundant COM Mode.........................................................8-1
Accessing the Console Utility............................................................................................ 8-2
Selecting theApplication ................................................................................................... 8-3
Configuring Redundant COM Mode.................................................................................. 8-4
Configuring the Serial Ports............................................................................................... 8-7
Save.................................................................................................................................... 8-8
Restart ................................................................................................................................ 8-8
Chapter 9 Setting Up Reverse Terminal..................................................................9-1
Accessing the Console Utility............................................................................................ 9-2
Selecting theApplication ................................................................................................... 9-3
Configuring RTELNET Mode............................................................................................ 9-4
Configuring the Serial Ports............................................................................................... 9-5
Save.................................................................................................................................... 9-7
Restart ................................................................................................................................ 9-7

Chapter 10 Setting Up Terminal...............................................................................10-1
Accessing the Console Utility.......................................................................................... 10-2
Selecting theApplication ................................................................................................. 10-3
Configuring TERM_ASC Mode ...................................................................................... 10-4
Configuring TERM_BIN Mode ....................................................................................... 10-7
Configuring the Serial Ports............................................................................................. 10-9
Save................................................................................................................................ 10-10
Restart .............................................................................................................................10-11
Chapter 11 Setting Up Multi-host TTY.....................................................................11-1
Accessing the Console Utility...........................................................................................11-2
Selecting theApplication ..................................................................................................11-3
Configuring FIXTTY Mode..............................................................................................11-4
Configuring the Serial Ports..............................................................................................11-5
Save...................................................................................................................................11-7
Restart ...............................................................................................................................11-7
Setting up Hosts ................................................................................................................11-8
Installing and Compiling Fixed TTY Driver......................................................... 11-8
Fixed TTY Driver for Different Applications....................................................... 11-9
Using Fixed TTY Driver..................................................................................... 11-10
Chapter 12 Setting Up Dialin/out .............................................................................12-1
Accessing the Console Utility.......................................................................................... 12-2
Selecting theApplication ................................................................................................. 12-3
Configuring PPPD/PPP Mode.......................................................................................... 12-4
Configuring SLIPD/SLIP Mode....................................................................................... 12-6
Configuring Dynamic Mode ............................................................................................ 12-8
Configuring the Serial Ports........................................................................................... 12-13
Configuring Modem Initialization.................................................................................. 12-14
Optional Welcome Message........................................................................................... 12-15
Configuring Optional Local User Information............................................................... 12-15
Save................................................................................................................................ 12-16
Restart ............................................................................................................................ 12-16
Chapter 13 Setting Up Printer..................................................................................13-1
Accessing the Console Utility.......................................................................................... 13-2
Selecting theApplication ................................................................................................. 13-3
Configuring RAW PRN Mode ......................................................................................... 13-4
Configuring LPD PRN Mode........................................................................................... 13-6
Configuring the Serial Ports............................................................................................. 13-7
Save.................................................................................................................................. 13-8
Restart .............................................................................................................................. 13-9
Setting up Unix Hosts ...................................................................................................... 13-9
Setting up a SCO Unix Host............................................................................... 13-10
Setting up a SOLARIS X86 Host........................................................................ 13-11
Setting up a LINUX Host.................................................................................... 13-12
Setting up Windows Hosts ............................................................................................. 13-13
Setting up a Windows NT Host .......................................................................... 13-13
Setting up a Windows 2000 Host........................................................................ 13-17

Chapter 14 Setting Up Multiplex..............................................................................14-1
Accessing the Console Utility.......................................................................................... 14-2
Selecting theApplication ................................................................................................. 14-3
Configuring the “Host” CN2610...................................................................................... 14-3
Configuring the “Device” CN2610.................................................................................. 14-7
Configuring the Serial Ports............................................................................................14-11
Save................................................................................................................................ 14-12
Restart ............................................................................................................................ 14-13
Chapter 15 Setting Up Routing................................................................................15-1
Accessing the Console Utility.......................................................................................... 15-2
What is RIP? ....................................................................................................................15-3
Configuring RIP............................................................................................................... 15-3
Configuring the Static Routing Table............................................................................... 15-4
Static Routing Examples.................................................................................................. 15-5
Configuring Routes to the Internet........................................................................ 15-5
Configuring Routes to the Internet and Intranet.................................................... 15-6
Configuring Multiple-Point Routes....................................................................... 15-7
Save.................................................................................................................................. 15-8
Restart .............................................................................................................................. 15-8
Chapter 16 Administrative Utilities..........................................................................16-1
Ping .................................................................................................................................. 16-2
Monitor............................................................................................................................. 16-2
Line....................................................................................................................... 16-3
Network ................................................................................................................ 16-4
Async.................................................................................................................... 16-5
Routing.................................................................................................................. 16-6
PPP-Trace ............................................................................................................. 16-6
Diagnostic ........................................................................................................................ 16-7
Upgrade............................................................................................................................ 16-8
Upgrading with the Windows Utility.................................................................... 16-8
Console Terminal Upgrade................................................................................... 16-9
Upgrading through the Serial Console................................................................ 16-11
Remote RCP Upgrade......................................................................................... 16-14
Windows Driver Manager Utility................................................................................... 16-16
Installing CN2610 Windows Driver Manager .................................................... 16-16
Using CN2610 Windows Driver Manager.......................................................... 16-19
Windows Monitor Utility............................................................................................... 16-27
Installing CN2610 NPort Monitor Utility........................................................... 16-27
Using NPort Monitor Utility............................................................................... 16-30
Export............................................................................................................................. 16-32
Console Terminal Export.................................................................................... 16-32
Remote RCP Export............................................................................................ 16-35
Import............................................................................................................................. 16-35
Console Terminal Import.................................................................................... 16-35
Remote RCP Import............................................................................................ 16-38
Default............................................................................................................................ 16-39

Appendix A Troubleshooting.....................................................................................A-1
Console Terminal Problems .............................................................................................. A-2
Configuring Dual Ethernet Ports....................................................................................... A-4
Terminal Port Problems..................................................................................................... A-5
Saving the CN2610’s Parameters...................................................................................... A-5
ASPP Port Problems.......................................................................................................... A-6
SLIP/PPP Connection Problems........................................................................................ A-6
RADIUS Problems............................................................................................................ A-6
Appendix B RADIUS Server........................................................................................B-1
What is RADIUS?..............................................................................................................B-2
Definition................................................................................................................B-2
Client/Server Architecture ......................................................................................B-2
Setting up the CN2610.......................................................................................................B-2
Setting up the RADIUS Server IP Address.............................................................B-2
Setting up Port Configuration .................................................................................B-3
Setting up UNIX Hosts ......................................................................................................B-5
Installing the RADIUS Execution File....................................................................B-5
RADIUS Server Configuration...............................................................................B-6
Basic/Extended Permission Group Setting .............................................................B-7
Setting up Windows NT Hosts.........................................................................................B-11
Setting up Windows 2000 Hosts ......................................................................................B-13
Setting up Windows 2003 Hosts ......................................................................................B-16
Appendix C SNMP Agent with MIB II .........................................................................C-1
Appendix D Pin Assignments and Cable Wiring......................................................D-1
Pin Assignments................................................................................................................ D-2
10/100BaseTX Port Pin Assignment ..................................................................... D-2
Console Port Pin Assignment................................................................................. D-2
Async RS-232 Port Pin Assignment ...................................................................... D-2
Cable Wiring ..................................................................................................................... D-2
10/100BaseTX Port Cable Wiring ......................................................................... D-2
Async RS-232 Port Cable Wiring.......................................................................... D-3
DB9 and DB25 Connector Pin Assignments ......................................................... D-4
Appendix E LCM Display............................................................................................ E-1

1
1
Chapter 1 Introduction
MOXA’s CN2610 dual-LAN async server is available in models with 8 or 16 asynchronous
RS-232 ports, and all models come with two 10/100 Mbps Ethernet LAN ports. The CN2610
dual-LAN async server is used to connect terminals, modems, printers, and other asynchronous
serial devices to LAN hosts. The CN2610 complies with TCP/IP and IEEE 802.3 specifications
using standard Ethernet 10/100BaseT and twisted pair 10/100BaseTX cable as the data
transmission medium.
The following topics are covered in this chapter:
Product Features
¾Hardware
¾Software
Package Checklist
Front Panel
Rear Panel
Bottom Label

CN2610 User’s Manual Introduction
1-2
Product Features
Hardware
yDual LAN ports (auto-detecting 10/100 Mbps Ethernet)
ySurge protection for each serial port
y4 MB RAM, 2 MB Flash ROM
yTx/Rx LED for each serial port
ySystem Status LEDs
yEthernet Status LEDs
y8 or 16 RJ45 RS-232 serial ports, with up to 921.6 Kbps transmission speed
Software
yASCII/Binary terminal modes with up to 8 Telnet and Rlogin sessions
yPoint to Point Protocol (PPP and PPPD)
ySerial Line Internet Protocols (SLIP and SLIPD)
yDynamic auto-recognition of Terminal, SLIP, or PPP
yDial-on-demand, Dial-out
yRemote serial or parallel printing (RLP)
yCN2610 Async Server Proprietary Protocol (ASPP) for TCP/IP socket programming
yRAW mode for transparent data transmission
yReverse Telnet
ySNMP Agent for network management
yNetwork protocols: TCP/IP, UDP, ICMP, NetBEUI, DHCP
yApplication protocols: Telnet, Rlogin, Rtelnet, RAW TCP, RAW UDP, RCP, WINS,
DRDAS™, LPD, DNS, Multi-Host
ySecurity protocols: RADIUS, Dial-back, PAP, CHAP, Local user/password
yReal COM port drivers (Windows 95/98/ME/NT/2000/XP/2003/XP x64/2003 x64/Vista x64)
yReal TTY drivers (Linux kernels 2.2.x, 2.4.x, 2.6.x)
ySCO Unix, SCO OpenServer 5, SCO OpenServer 6, UnixWare 7,SVR4.2, QNX 4.25, QNX 6,
Solaris 10, FreeBSD 5, FreeBSD 6
yStatic Routing, RIP I/II protocols
yWindows-like administrative CONSOLE utility from a fixed console port, or by Telnet from a
networked host
yPassword protection and extensive user verification functions
yEasy firmware upgrade via Flash ROM
Package Checklist
CN2610 dual-LAN async servers are shipped with the following items:
yCN2610 Dual-LAN Async Server
yAC power cord
yDocumentation and Software CD-ROM
yQuick Installation Guide (English and Simplified Chinese versions)
yRJ45 Loopback Tester
yProduct Warranty Booklet
yRackmount Kit (includes 2 brackets and 8 screws)
yDesktop Kit (includes 4 pads)

CN2610 User’s Manual Introduction
1-3
Front Panel
Rx
Tx 12345678910111213141516
Reset Ready
SELMENU
CN2610 16 port RS-232 Async Server
LCM Display Panel
Reset Button Ready LED
Push Buttons
LED Indicators
Feature Description
Reset Button Press the Reset button for 5 seconds to load factory defaults. The CN2610 will
beep twice when the configuration has been reset.
Push Buttons Used for configuring the IP address and other parameters.
Red Indicates that the CN2610 is receiving power
Ready LED Green Indicates that the CN2610’s OS is ready
Serial Tx Green Indicates serial port transmission
Serial Rx Yellow Indicates serial port reception
Rear Panel
12345678
Serial ports
AC POWER 100-240V, 47-63Hz
Console LAN1 LAN2
9 10111213141516
10/100BaseT Ethernet Ports
RS-232 Console Port Serial PortsPower Input
Power On/Off Switch
Socket / Port Description
AC Power Input CN2610-8 and CN2610-16:
Automatic detection of 100-240V, 47-63 Hz AC power supply
Power On/Off Switch I indicates power on; O indicates power off (AC models only)
Console 8-pin RJ45 RS-232 port for console terminal connection
LAN 1 8-pin RJ45 auto-detectable 10/100 Mbps UTP port
LAN 2 8-pin RJ45 auto-detectable 10/100 Mbps UTP port
Serial Ports 8 or 16 8-pin RJ45 ports for DCE modem-type connections
Bottom Label
The server’s serial number and MAC address are printed on a label fixed to the bottom of the
server. The CN2610 has 2 LAN ports, each with its own MAC address. The MAC address is the
unique hardware Ethernet address used to identify a network hardware product. Write each of the
two MAC addresses in the space provided below for future reference.
LAN 1 MAC address:_______________________________
LAN 2 MAC address:_______________________________

2
2
Chapter 2 Getting Started
This chapter includes instructions on where and how to install the CN2610 dual-LAN async server.
Both basic and advanced software configuration instructions are given.
The following topics are covered in this chapter:
Hardware InstallationDesktop
¾Rackmount
¾Wiring Requirements
¾Connecting the CN2610-8/16’s Power
¾Connecting to the Network
¾Connecting to a Serial Device
¾Connecting to the Console Port
Accessing the Console Utility
¾Configuration Checklist
¾Accessing the Console from a Telnet Terminal
¾Accessing the Console from a Telnet Terminal
Configuring the CN2610—The Server Menu
¾Server Configuration—Info.
¾Server Configuration—LAN
¾Server Configuration—Adv.
¾Server Configuration—Host_table
¾Server Configuration—Route_table
¾Server Configuration—User_table
Save
Restart

CN2610 User’s Manual Getting Started
2-2
Hardware Installation
Desktop
Place your CN2610 on a clean, flat, well-ventilated desktop. For better ventilation, attach the 4
pads from the desktop kit to the bottom of the unit, and leave some space between the CN2610 and
other equipment. Do not place equipment or objects on top of the unit, as this might damage the
server.
Bottom of CN2610
Pads
Rackmount
The CN2610 is designed to be mounted on a standard 19-inch rack. Use the enclosed pair of
L-shaped metal brackets and screws to fasten your CN2610 to the rack cabinet. Each L-shaped
bracket has 6 holes, leaving two outer or inner holes available for other uses. You have two
options. You can lock either the front or rear panel of the CN2610 to the front of the rack. Locking
the front panel is shown in the following figure.
Rackmount rail
L-Shaped Metal Bracket
Screws
12345678
Serial ports
Console LAN
9 10111213141516
Rx
Tx 12345678910111213141516
Reset Ready
SELMENU
CN2610
16 port RS-232 Async Server

CN2610 User’s Manual Getting Started
2-3
Wiring Requirements
ATTENTION
Safety First!
Be sure to disconnect the power cord before installing and/or wiring your CN2610.
Wiring Caution!
Calculate the maximum possible current in each power wire and common wire. Observe all
electrical codes dictating the maximum current allowable for each wire size.
If the current goes above the maximum ratings, the wiring could overheat, causing serious
damage to your equipment.
Temperature Caution!
Be careful when handling the CN2610. When plugged in, the CN2610’s internal components
generate heat, and consequently the board may feel hot to the touch.
You should also observe the following common wiring rules:
yUse separate paths to route wiring for power and devices. If power wiring and device wiring
paths must cross, make sure the wires are perpendicular at the intersection point.
NOTE: Do not run signal or communication wiring and power wiring in the same wire
conduit. To avoid interference, wires with different signal characteristics should be routed
separately.
yYou can use the type of signal transmitted through a wire to determine which wires should be
kept separate. The rule of thumb is that wiring that shares similar electrical characteristics can
be bundled together.
yKeep input wiring and output wiring separate.
yWhere necessary, it is strongly advised that you label wiring to all devices in the system.
Connecting the CN2610-8/16’s Power
Connect the CN2610’s 100-240 VAC power line to its AC connector. If the power is properly
supplied, the “Ready” LED will show a solid red color until the system is ready, at which time the
color changes to green.
Connecting to the Network
Connect one end of the Ethernet cable to the CN2610’s 10/100M Ethernet port and the other end
of the cable to the Ethernet network. There are 2 LED indicators located on the top left and right
corners of the Ethernet connector. If the cable is properly connected, the CN2610 will indicate a
valid connection to the Ethernet in the following ways:
81
The top right corner LED indicator maintains a solid green color when the cable is
properly connected to a 100 Mbps Ethernet network.
81
The top left corner LED indicator maintains a solid orange color when the cable is
properly connected to a 10 Mbps Ethernet network.

CN2610 User’s Manual Getting Started
2-4
Connecting to a Serial Device
Use appropriately wired serial data cables to connect serial devices to the CN2610’s serial ports.
Connecting to the Console Port
A console is a combination of keyboard and monitor that is used to configure settings and monitor
the status of your system. The console port can be used if a network is unavailable, or you do not
know the CN2610’s IP address. To connect to the console port, use a PC running UNIX, or a PC
with terminal emulation software (e.g., HyperTerminal or PComm by MOXA; parameter settings
are: baudrate = 115200 bps, parity check = None, data bits = 8, stop bits = 1, terminal type =
VT100). Use an RJ45-to-DB25 or RJ45-to-DB9 cable to connect the terminal to the console port.
Accessing the Console Utility
The Console Utility is the main application used to set up the server, configure the ports, and run
utilities (ping, diagnosis, monitor, and upgrade). There are two ways to access the Console
Utility—with terminal emulation from a console terminal, or with Telnet from a network terminal.
NOTE If your network is already set up, telnet over the network to the CN2610’s IP address to access the
Console Utility. If your network environment is not set up, use MOXA PComm Terminal to
establish a direct serial console connection.
Configuration Checklist
You will need the following information to configure the CN2610. Check with your network
administrator if you do not know all of the required information.
Basic CN2610 Information:
Name
Location
LAN1 IP address
LAN1 IP netmask
LAN1 default gateway IP address
LAN2 IP address
LAN2 IP netmask
LAN2 default gateway IP address
Domain server 1 IP address
Domain server 2 IP address
WINS server IP address
Console password
Accessing the Console from a Telnet Terminal
Connect the CN2610 to your LAN and then turn on the power. Use the MOXA Windows Utility to
find the CN2610’s IP address, and then telnet to the IP address to enter the CN2610 console.

CN2610 User’s Manual Getting Started
2-5
CN2610 Windows Utility
The CN2610 Utility is a convenient Windows utility that can be used to find both the name and IP
address of your CN2610. Once you know the IP address, you can telnet the CN2610 over the
network to complete the configuration process and to gather information about all servers on the
network.
1. Run upgrade.exe, located in the \Software\Firmware\ folder on the CN2610 Documentation
and Software CD, or run CN2610 Tool ÆFirmware Utility from the Start menu.
2. The CN2610 Utility will search for all CN2610s on the network.
3. The CN2610 Utility lists all available servers on the network. Note that servers in grey are
password protected. Double click the server’s name, or click from the menu bar to see
the server settings.

CN2610 User’s Manual Getting Started
2-6
4. The server’s general information is shown in the CN2610 Server General Info. window. If
necessary, change the settings, and then click OK to accept the change.
5. If you can’t find the server in the list, double-check the server’s power and network
connections, and then use search to try locating the server again.
Using Telnet
1. Telnet over the network to the server’s IP address.
2. Type 1to choose ansi/vt100, and then press Enter.
Telnet 192.168.127.254
Async Server CN2610-8
Console terminal type (1: ansi/vt100, 2: vt52) : 1
3. The CN2610’s MAIN MENU will open, as shown below.
Telnet 192.168.127.254
CN2610-8 CN2610-8_19 V2.0 MAIN MENU
------------------------------------------------------------------------------
[Server] Port seTting sAve Utility Restart Exit
Examine/modify async server node/table configuration
Enter: select ESC: previous menu

CN2610 User’s Manual Getting Started
2-7
Use the following keystrokes to navigate the CN2610’s console utility.
Action Key
Move [Up/Down/Left/Right] Arrow Key or [Tab] Key
Jump to next menu, or
Select item [Enter] Key
Return to previous menu, or
Close pop up selector [Esc] Key
Shortcut Key Capitalized letter of the word
Accessing the Console from a Console Terminal
If you do not know the CN2610’s IP address, or it is not possible to use Telnet, you can use a
direct console connection to enter the CN2610 console. Use a terminal emulation program for the
console PC, such as HyperTerminal or MOXA PComm Terminal Emulator.
1. If you are using Windows 9x/ME/NT, run PComm26.exe from the Win9xNT directory. If
you are using Windows 2000/XP/2003, run PComm2K.exe , as shown in the figure below,
from the Win2kXP2003directory.

CN2610 User’s Manual Getting Started
2-8
2. Click Next to Continue.
3. Select the I Agree option and then click Next.

CN2610 User’s Manual Getting Started
2-9
4. Select a directory in which to install the CN2610 Utility, and then click Next.
5. Click Next to continue.

CN2610 User’s Manual Getting Started
2-10
6. Wait while the PComm Lite software is installed.
7. Click Close.