Moxa Technologies NPort 5600-8-DTL Series User manual

P/N: 1802056000013
*1802056000013*
NPort 5600-8-DTL
Quick Installation Guide
Edition 3.1, November 2018
Technical Support Contact Information
www.moxa.com/support
Moxa Americas:
Toll
-free: 1-888-669-2872
Tel:
1-714-528-6777
Fax:
1-714-528-6778
Moxa China (Shanghai office):
Toll
-free: 800-820-5036
Tel:
[phone]
Fax:
[phone]
Moxa Europe:
Tel:
[phone]
Fax:
[phone]
Moxa Asia-Pacific:
Tel:
[phone]
Fax:
[phone]
Moxa India:
Tel:
[phone]
Fax:
[phone]

2018 Moxa Inc. All rights reserved.

- 2 -
Overview
The NPort 5600-8-DTL series includes the following models:
•NPort 5610-8-DTL: 8 ports, RS-232, 0 to 60°C
•NPort 5650-8-DTL: 8 ports, RS-232/422/485, 0 to 60°C
•NPort 5650I-8-DTL: 8 ports, RS-232/422/485, 0 to 60°C, 2KV
optical isolation.
•NPort 5610-8-DTL-T: 8 ports, RS-232, -40 to 75°C
•NPort 5650-8-DTL-T: 8 ports, RS-232/422/485, -40 to 75°C
•NPort 5650I-8-DTL-T: 8 ports, RS-232/422/485, 2KV optical
isolation, -40 to 75°C
Package Checklist
The NPort 5600-8-DTL package should contain the following items:
•NPort 5600-8-DTL device server
•Wall mounting and DIN-Rail kits
•Stick-on pads
•Power adapter (not including T models)
•Documentation and software CD
•Quick installation guide (printed)
•Warranty card
Optional Accessories*
•DK-35A: DIN-Rail mounting kit (35 mm)
NOTE
Note: Please notify your sales representative if any of the
above items are missing or damaged.
*Optional Accessories can be ordered separately.
NOTE
The operating temperature of the power adapter in the box is
from 0 to 40°C. If your application is out of this range, please
use a power adapter supplied by UL Listed External Power
Supply (The power output meets SELV and LPS a
nd rated 12 -
48 VDC, minimum current 0.73 A). Moxa has power adapters
with wide temperature range (
-40 to 75°C, -40 to 167°F), the
PWR-12150-(plug type)-SA-T series, for your reference.

- 3 -
Hardware Introduction
Top and Rear Views
Front View
Reset Button
Use a pointed object to hold the reset button down for at least five
seconds to load the factory defaults. Release the reset button when the
Ready LED stops blinking.
LED Indicators
The LED indicators on the top panel are used to display the status as
follows:
Name
Color
Function
PWR
red
Power is on.
off
Power is off.
Ready
green
Steady: NPort is operational
Blinking: NPort is responding to NPort
Administrator “Locate” function or NPort is
resetting to factory default
off
Power is off or fault condition exists.
Fault
red
IP conflict or DHCP or BOOTP server did not
respond properly.
off
No fault condition detected.
Link
green
Steady: Network is connected; no data is being
transmitted.
Blinking: Network is connected; data is being
transmitted.
off
Ethernet cable is disconnected or has a short.
green
Serial port has been opened by server side
software.

- 4 -
Name
Color
Function
InUse
(P1 to
P8)
off
Serial port is not currently opened by server
side software.
TX/RX
(P1 to
P8)
green (Tx)
Serial device is transmitting data.
orange (Rx)
Serial device is receiving data.
off
No data is flowing to or from the serial port.
Hardware Installation
STEP 1: After removing the NPort 5600-8-DTL from the box, place it on
a desktop or other horizontal surface. Connect the 12-48 VDC power
adaptor to the NPort 5600-8-DTL’s power input when using an AC
power source, or connect the NPort 5600-8-DTL’s terminal block
directly to a DC power source.
STEP 2: Use an Ethernet cable to connect the NPort 5600-8-DTL to a
network hub or switch. You can also connect directly to your computer’s
Ethernet port, which is convenient for initial configuration or testing.
STEP 3: Connect the NPort 5600-8-DTL’s serial port to a serial device.
Wall or Cabinet Mounting
The NPort 5600-8-DTL comes with two metal attachment plates to
allow installation on a wall or the inside of a cabinet. First, attach the
brackets to the back of the NPort with screws. Next, mount the unit on
a wall or cabinet with screws. Screws should be less than 6.0 mm in
head diameter, and less than 3.5 mm in shaft diameter.
DIN-Rail Mounting
DIN-Rail attachments can be purchased separately to attach the
product to a DIN-Rail. The DIN-Rail attachments should be oriented
with the metal springs on top.
Standard Attachment
DK-35A Attachment

- 5 -
NOTE
The operating temperature of the power adapter in the box is
from 0 to 40°C. If your application is out of this range,
please
use a power adapter supplied by UL Listed External Power
Supply (The power output meets SELV and LPS and rated 12
-
48 VDC, minimum current 0.73 A). Moxa has power adapters
with wide temperature range (
-40 to 75°C, -40 to 167°F), the
PWR-12150-(plug type)-SA-T series, for your reference.
Software Installation Information
For the NPort’s configuration, the default IP address of the NPort is:
LAN: Static; IP = 192.168.127.254; netmask = 255.255.255.0
NOTE
If you have forgotten the NPort's IP address, use the Device
Search Utility (DSU) from your PC to locate the NPort. After
searching the LAN for NPort units, the DSU will display the IP
address of each unit.
You may log in with the password moxa to change any setting to meet
your network topology (e.g., IP address) or serial device (e.g., serial
parameters). For first-time use, click the Wizard in the left navigation
panel. The wizard will prompt you to configure the IP address, SSID,
and security mode. For other settings, use the factory defaults or
modify the settings for your application.
For software installation, download the relative utilities from Moxa's
website:
https://www.moxa.com/support/support_home.aspx?isSearchShow=1
•Download the NPort Windows Driver Manager and install it as the
driver to run with Real COM mode of the NPort Series.
•Execute NPort Windows Driver Manager; then map the virtual COM
ports on your Windows platform.
•You may refer to the DB9 Male Ports pin assignment section to loop
back pin 2 and pin 3 for the RS-232 interface to carry out a self test
on the device.
•Use HyperTerminal or a similar program (you may download Moxa's
program, called PComm Lite) to test whether the device is good or
not.
Pin Assignments
Pin RS-232
RS-422/
RS-485-4W
RS-485-2W
1
DCD
TxD-(A)
–
2
RxD
TxD+(B)
–
3
TxD
RxD+(B)
Data+(B)
4
DTR
RxD-(A)
Data-(A)
5
GND
GND
GND
6
DSR
–
–
7
RTS
–
–
8
CTS
–
–
9
–
–
–
DB9 Male Ports

- 6 -
Note: The NPort 5610-8-DTL supports RS-232 only.
Specifications
LAN
Ethernet Ports
10/100 Mbps (RJ45)
Protection
Built-in 1.5 KV magnetic isolation
Serial Interface
RS-232
NPort 5610-8-DTL
RS-232/422/485
NPort 5650-8-DTL, 5650I-8-DTL
Serial Ports
8 (DB9-M connectors)
Isolation
2 KV isolation (NPort 5650I-8-DTL)
Serial Signals
RS-232
TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
RS-422
Tx+, Tx-, Rx+, Rx-, GND
RS-485 (2-wire)
Data+, Data-, GND
RS-485 (4-wire)
Tx+, Tx-, Rx+, Rx-, GND
Serial Line Protection
15 KV ESD for all signals
RS-485 Data Direction
ADDC™ (Automatic Data Direction Control)
Serial Communication Parameters
Parity
None, Even, Odd, Space, Mark
Data Bits
5, 6, 7, 8
Stop Bit(s)
1, 1.5, 2
Flow Control
RTS/CTS, DSR/DTR (for RS-232 only),
XON/XOFF
Transmission Speed
50 bps to 921.6 Kbps
Power Requirements
Power Input
12 to 48 VDC
Physical Characteristics
Operating Temperature
Standard Models: 0 to 60°C (32 to 140°F)
Wide Temp. Models: -40 to 75°C (-40 to
167°F)
Storage Temperature
-40 to 85°C (-40 to 185°F)
Operating Humidity
5 to 95% RH
Material
SECC sheet metal (0.8 mm)
Dimensions Without ears: 197 × 44 × 125 mm
With ears: 229 × 46 × 125 mm
With DIN-Rail kit: 197 × 52.8 × 125 mm
Certifications
Regulatory Approvals
FCC Class A, CE Class A, UL 60950-1, LVD
Warranty
5 years