mr. steam iTEMPO Instruction manual

2020-10-30
Basic Butler / Linear
iTempo Control PUR100474 10-19
AromaSteam SteamHead
Linear Steamhead
PUR100421
PUR103936
10-15
06-20
MS / Super AutoFlush PUR100200E 09-19
Condensation Pan TS0012 02-19

iTEMPO®& iTEMPOPLUS®CONTROLS
Installation, Operation & Maintenance Manual
mr
.steam® Feel Good Inc.
www.mrsteam.com

2
HYPERTHERMIA occurs when the
internal temperature of the body
reaches a level several degrees above
the normal body temperature of 98.6°
F. The symptoms of hyperthermia
include an increase in the internal
temperature of the body, dizziness,
lethargy, drowsiness, and fainting. The
effects of hyperthermia include:
a) Failure to perceive heat;
b) Failure to recognize the need to exit
the steambath;
c) Unawareness of impending risk;
d) Fetal damage in pregnant women;
e) Physical inability to exit the steam-
bath;
and
f) Unconsciousness.
The use of alcohol, drugs, or medica-
tion can greatly increase the risk of
hyperthermia.
When installing and using this electrical equipment, basic safety
precautions should always be followed, including the following:
IMPORTANT SAFETY INSTRUCTIONS
1. READ AND FOLLOW ALL INSTRUCTIONS
2. Supervise children at all times.
3. Steam is hot and can cause injury or death
if improperly used. Steam rooms contain steam and ele-
vated temperatures. Please read and observe all warnings
in this manual before installing or using a steam room.
4. To reduce the risk of injury:
A. The wet surfaces of steam enclosures may be slippery.
Use care when entering or leaving.
B. The steam head is hot. DO NOT touch the steamhead
and avoid the steam near the steamhead.
C. Prolonged use of the steam system can raise exces-
sively the internal human body temperature and impair
the body’s ability to regulate its internal temperature
(hyperthermia). Limit your use of steam to 10-15 min-
utes until you are certain of your body’s reaction.
D. Excessive temperatures have a high potential for caus-
ing fetal damage during the early months of pregnancy.
Pregnancy or possibly pregnant women should consult a
physician regarding correct exposure.
E. Obese persons and persons with a history of heart disease,
low or high blood pressure, circulatory system problems,
or diabetes should consult a physician before using a
steambath.
F. Persons using medication should consult a physician before
using a steambath since some medication may induce
drowsiness while other medications may affect heart rate,
blood pressure and circulation.
SAVE THESE INSTRUCTIONS
WARNING
!
WARNING
!
WARNING
!
WARNING
!

mr
.steam®Installation & Operating Instructions
_________________________________________________________________
3
READ ME FIRST!
As you follow these instruc-
tions, you will notice warning and caution
symbols. This blocked information is impor-
tant for the safe and efficient installation
and operation of this generator. These are
types of potential hazards that may occur
during installation and operation:
Indicates a potentially
hazardous situation, which, if not avoided,
could result in death or serious injury.
Indicates a potentially
hazardous situation, which, if not avoided
may result in minor or moderate injury or
product damage.
IMPORTANT NOTE: This highlights
information that is especially relevant to
a problem-free installation.
All information in these instructions is
based on the latest product information
available at the time of publication.
Sussman-Automatic Corporation reserves
the right to make changes at any time
without notice.
Table of Contents:
Important Safety Instructions.............................. 3
Before Installing.................................................. 5
Dimensional Information .................................... 6
Installations......................................................7-9
iTempo Operating Instructions ...................10-11
iTempoPlus Operating Instructions.............12-15
Care and Maintenance ..................................... 16
Warranty ........................................................... 16
WARNING
!
WARNING
!
CAUTION
!

mr
.steam®Installation & Operating Instructions
_________________________________________________________________
4
BEFORE INSTALLING
Carefully inspect the control and packaging for shipping
damage. In the event of shipping damage, please contact
the carrier for claim information. Our customer service de-
partment can assist you with any missing or damaged parts.
To avoid unintentional steambath
operation, do not locate the control where other controls,
accessories, shower heads, valves, body sprays or similar
within the shower could cause confusion or interfere with
the MrSteam control’s intended use and function.
Do not use any iTempoPlus®, iTempo®, HomeWizard®or
iGenie®controls without reading and understanding the
respective Installation and Operation Manual and MrSteam
steam generator Installation and Operation Manual. Failure
to read and understand these instructions may result in an
inoperative or hazardous installation.
A peel and stick warning sticker is provided
in the MrSteam steam generator Installation, Operation
and Maintenance Manual. This manual is provided with
every steam generator. The warning sticker must be read
and permanently affixed in a conspicuous location near the
steam room. Failure to read and affix this warning sticker in
a conspicuous location may result in serious injury or death.
Please call MrSteam at 800 767-8326 for a free replacement
or if you have any questions regarding the warning sticker.
Install the iTempo or iTempoPlus controls according to
installation instructions. Failure to install according to in-
structions will result in an inoperative control or hazardous
overheating or inadequate heating of the steam room.
Failure to install according to instructions will result in an
inoperative control and overheating of the steam room.
IMPORTANT NOTE: If the desired location for the control
is outside the steam room a Remote Temperature Probe
(MSTS) must be installed inside the steam room. Contact
CAUTION
!
MrSteam technical service 1-800-767- 8326 for
more information on the Remote Temperature
Probe.
Do not route iTempoPlus, iTempo,
HomeWizard or iGenie control wiring inside conduit
together with power lines or close to hot water or
steam piping. Doing so may result in an inoperative
or hazardous installation.
Do not alter or modify any MrSteam
product. Doing so may result in an inoperative or
hazardous installation and will void the warranty.
IMPORTANT NOTES:
•
Turn power to the steam generator OFF before
connecting the control to the generator. Failure
to turn the power off will result in an inoperable
control.
• Do not operate iTempoPlus, iTempo, Home
Wizard or iGenie controls with anything other
than a MrSteam iTempo compatible steam gen-
erator. MrSteam residential steam generators
with serial numbers lower than 900000, or any
other brand of steam generator are not to be op-
erated with iTempo controls. Doing so may result
in an inoperative installation.
• This document contains important safety, opera-
tion and maintenance information. Leave this
document with the homeowner. Do not discard
this document.
• Discontinue use of the steam generator or control
if the steam generator is damaged or otherwise
not functioning properly. Doing so may result in
an inoperative or hazardous installation.
• All illustrations are for illustrative purposes only.
WARNING
!
WARNING
!
WARNING
!

mr
.steam®Installation & Operating Instructions
_________________________________________________________________
5
Drawings for Illustrative Purposes Only.
21 /2”
41 /2”
1
/4”
3/8”
3/4”
1”
5”
5”
33/4”
12” long
pigtail
Dimensional Information
for the Round and Square
iTempo®and iTempoPlus®
Box Contents:
• iTempo or iTempoPlus Control
• Control Cable (30 ft.)
• Steam head
• Tube of Silicone sealant
• Owner’s Manual

mr
.steam®Installation & Operating Instructions
_________________________________________________________________
6
Installation Instructions for Round & Square
iTempo®and iTempoPlus®
IMPORTANT NOTE: If the desired location for the control is outside
the steam room a Remote Temperature Probe (MSTS) must be installed
inside the steam room. Contact MrSteam technical service 1-800-767-
8326 for more information on the Remote Temperature Probe.
NOTE: The connector is keyed with the flat facing up. The control cable is the
same at both ends.
STEP 1
Determine the desired installation location of the control. The iTempo and
iTempoPlus controls are designed to be installed inside or outside the steam
room as a matter of personal preference. If the control is installed inside the
steam room the control must be located:
• 4-5 feet above the oor near the bather seating area.
• The control features an integral temperature sensor. Locate the control in a
location representative of the desired steam bathing temperatures. Do not
locate the control above or near the steam head or direct steam emissions.
Locating the controls near the steamhead or near direct steam emissions may
result in poor steam room temperature control.
• On a vertical wall
• The control cable length is 30 feet. Insure that the control and/or steam
generator are located accordingly. Contact a MrSteam technical
service representative if a longer cable is required (60 ft. cable, PN
103990-60).
IMPORTANT NOTE: The control cable should be run in a dedicated
1” conduit to facilitate installation and service. Be careful not to strain,
staple, pinch or otherwise damage the control cable. Route cable as
required to permit replacement. Do not route cable inside conduit
together with power lines or close to hot water or steam piping.
Drawings for Illustrative Purposes Only.
2-5
⁄ 8”
3-7
⁄ 8”
DIAGRAM 1

mr
.steam®Installation & Operating Instructions
_________________________________________________________________
7
Drawings for Illustrative Purposes Only.
STEP 2 Diagram 1
Make a 2-5 ⁄8” wide by 3-7⁄8” high cutout
in the desired control location. Do not
oversize or under size the cutout.
STEP 3 Diagram 2
Route the control cable (provided with the
control) from the wall cutout to the steam
generator. Connect one end of the cable to
the steam generator connector.
NOTE: The connector is keyed with the
flat facing up. The control cable is the same
at both ends.
STEP 4 Diagram 3
Firmly connect the other end of the
cable to the control. Turn on power to
the steam generator and test the control
to verify correct connections. Test per
the instructions on pages 10-15. With
verification of proper control function,
proceed to Step 5.
If the generator is on for
more than a few minutes steam will start
coming out of the steamhead. Insure that
the steam room is not occupied.
DIAGRAM 3
DIAGRAM 4
DIAGRAM 2
CAUTION
!

mr
.steam®Installation & Operating Instructions
_________________________________________________________________
8
DIAGRAM 6
Drawings for Illustrative Purposes Only.
STEP 5 Diagram 4
Remove and discard peel-off paper to expose
adhesive liner.
STEP 6 Diagram 5
Run a bead of silicone (provided) as shown
to the outer edge of the control faceplate,
following the contour of the circle or square
shape. Use silicone as required to create a
moisture seal.
NOTE: The silicone supplied by MrSteam
can be used to meet a variety of sealing and
gasketing. It cures to silicone rubber and
adheres to glass, wood, metal, porcelain,
ceramic tile, painted surfaces, many plastics
and rubber. Surfaces must be clean and dry.
Apply thin layer of product. Fit together and
support if necessary. Allow excess material
to cure, then trim with a sharp blade.
Sealant “skins” in 5 minutes, dries to touch
in 1 hour. Fully cures and bonds in 24 hrs.
IMPORTANT NOTE: Do not apply
excessive amounts of silicone. Do not apply
silicone to any other parts of the control
including the adhesive gasket.
STEP 7 Diagram 6
Insure the mounting surface is clean and
dry as required for good adhesion. Hold
the control with the LED display in the
12 o’clock position and press the control
against the wall until the adhesive sticks
DIAGRAM 5

mr
.steam®Installation & Operating Instructions
_________________________________________________________________
9
The iTempo Control features programmable
digital temperature control, a fixed (60) minute
duration, ON/OFF and PAUSE. The control can be
set at a temperature range from 80˚fup to 120˚f
Set the steam bathing temperature
according to personal preference, however it is
highly recommended to begin steam bathing at a
low temperature setting for a very short
duration to gauge comfort and safety levels.
ON/OFF Diagram 1
Press the ON/OFF key to start or stop the ow
of steam. Steam will begin to flow a few minutes
after the control is turned ON. The duration re-
quired for the steam room to reach steam
bathing temperatures depends on the steam
room construction and steam generator specifica-
tions. Steam may continue to flow for a short time
after the control is turned OFF.
PAUSE FEATURE Diagram 2
If a pause in steam flow is desired press the
PAUSE key. The display will flash while the
control is in the PAUSE mode. The timer will
continue to countdown while in the PAUSE
mode. Steam may continue to flow for a short
time after pause is pressed.
DIAGRAM 1
DIAGRAM 2
iTempo
®
Operating Instructions
Drawings for Illustrative Purposes Only.
WARNING
!

mr
.steam®Installation & Operating Instructions
_________________________________________________________________
10
Display
Up Key
Pause Key
Down Key
ON/OFF
Key
mr.steam
DIAGRAM 3
DIAGRAM 4
TIMER FEATURE
When the control is turned ON a 60 minute time
duration is initiated. The control will turn off
after 60 minutes unless the control is turned off
manually.
MEMORY FEATURE
If the control is turned off manually before 60
minutes then the default temperature of 110˚F
will be used the next time the control is turned
on. If the control times out at 60 minutes (not
manually turned off) then the previous user tem-
perature setting will be used when the steam-
bath is used again.
SETTING THE TEMPERATURE
Diagram 3
The control is pre-set and will display the tem-
perature setting of 110˚F (default setting). Use
the UP and DOWN keys to change the tempera-
ture setting from 80˚ F to 120˚ F in one degree
increments.
CHANGING THE TEMPERATURE
UNITS
(F˚/C˚) Diagram 4
When the generator is Off, Press and hold ON/
OFF key for 10 seconds. The temperature units
will be displayed as Fahrenheit (TuF) or Celsius
(TuC). Use the UP/DOWN keys to choose
between (TuF) and (TuC). Press ON/OFF key to
accept the new units and exit.
Drawings for Illustrative Purposes Only.

mr
.steam®Installation & Operating Instructions
_________________________________________________________________
11
mr.steam
temp
aroma chroma
time
mr.steam
temp
aroma chroma
time
The iTempoPlus Control features programmable
temperature control, programmable time duration,
clock, AromaSteam, ChromaSteam®, ON/OFF and
two personal settings.
Set the steam bathing temperature
according to personal preference, however it is highly
recommended to begin steam bathing at a low
temperature setting for a very short duration to gauge
comfort and safety levels.
POWERING UP THE UNIT Diagram 1
When the generator is first powered up or after a
power interruption, the clock display flashes and the
clock is ready to be set up.
NOTE: Pressing the ON/OFF will start the generator
even if the clock has not been set.
NOTE: The clock can only be set when the generator
is OFF, the display is flashing.
SETTING THE CLOCK
ON/OFF
Diagram 2
Press the ON/OFF key to start or stop the ow of
steam. The Temperature Set Point is displayed. Steam
will begin to flow a few minutes after the control is
turned ON. The duration required for the steam room
to reach steam bathing temperatures depends on the
steam room construction and steam generator speci-
fications. Steam may continue to flow for a short time
after the control is turned OFF.
iTempoPlus
®
Operating Instructions
DIAGRAM 1
DIAGRAM 2
Drawings for Illustrative Purposes Only.
WARNING
!

mr
.steam®Installation & Operating Instructions
_________________________________________________________________
12
Drawings for Illustrative Purposes Only.
SETTING THE CLOCK Diagram 3
When the display is not flashing: Press and hold the
TIME key until the display starts flashing.
Use the UP/DOWN keys to select the desired time,
at this time the AM/PM logo will be displayed.
Press the TIME key to save changes.
SETTING THE STEAMBATH DURATION
Diagram 4
Press TIME key to set or display the steambath
duration time on the clock. The control is pre-set
and will display a TIME setting of 20 minutes (de-
fault setting). With the TIME or CLOCK displayed,
press the UP or DOWN keys (Diagram 5) to set the
desired duration time (2-60 minutes) in two minute
increments.
Set the steambath duration according to personal
preference, however it is highly recommended to
begin steam bathing at a very short duration to
gauge comfort and safety levels. The control will
turn off when the duration period times out. Then,
the clock time will be displayed.
DIAGRAM 3
DIAGRAM 4
DIAGRAM 5
mr.steam
temp
aroma

mr
.steam®Installation & Operating Instructions
_________________________________________________________________
13
mr.steam
aroma chroma
time
mr.steam
chroma
timetemp
aroma chroma
mr.steam
timetemp
SETTING THE TEMPERATURE
Diagram 6: Press TEMP key to set the desired temperature or
display the temperature setting.
Diagram 7: The control is preset and will display a tempera-
ture setting of 110˚F (default setting). With the temperature
displayed, press the UP or DOWN keys to set the desired tem-
perature (80°F to 120°F) in one degree increments.
Set the steam bathing temperature according to personal
preference, however it is highly recommended to begin steam
bathing at a low temperature setting to gauge comfort and
safety levels.
MEMORY FEATURE
If the control is turned off manually before it times out then the
default settings of 20 minutes and 110°F will be used the next
time the control is turned on. If the control times out (not manu-
ally turned off) then the previous user time and temperature
settings will be used when the steambath is turned on.
PERSONAL SETTINGS Diagram 8
Use the program key to store preferred settings.
To program preferred settings:
Press ON/OFF key to turn generator on.
Press the Program key once to program Pr 1.
Press it twice to program Pr 2. The selected parameter
will be displayed. Enter the preferred time and
temperature settings.
The iTempoPlus will store the following settings: set point, time
duration & aroma state. To select Pr 1 or Pr 2:
Press ON/OFF key then press the Program key once to
select Pr 1, press it twice to select Pr 2. The steambath will
begin to operate at the stored settings.
DIAGRAM 6
DIAGRAM 7
DIAGRAM 8
Drawings for Illustrative Purposes Only.

mr
.steam®Installation & Operating Instructions
_________________________________________________________________
14
mr.steam
chroma
timetemp
aroma
mr.steam
aroma
timetemp
chroma
CHANGING THE TEMPERATURE UNITS
(˚F/˚C)
When the generator is Off, Press and hold ON/OFF
key for 10 seconds. The temperature units will be
displayed as Fahrenheit (TuF) or Celsius (TuC). Use
the UP/DOWN keys to choose between (TuF) and
(TuC). Press ON/OFF key to accept the new value
and exit.
AROMASTEAM Diagram 9
The AromaSteam is an optional accessory that
automatically injects aromatic oil into the steam.
Press the ON/OFF key to turn the steam genera-
tor on. Then, press the AROMA key. The Aroma
indicator will be displayed. The AromaSteam
turns off automatically when the steam genera-
tor stops heating. Press the AROMA key to turn
it off during a steam session. The indicator will
turn off.
CHROMASTEAM
®Diagram 10
The ChromaSteam is an optional accessory that
provides colored light in the steam room. Press
the CHROMA key to turn light on. Press twice to
select the next color. Press again to turn the light
off. Note that the light can be turned ON even if
the steam generator is OFF.
DIAGRAM 9
DIAGRAM 10
Drawings for Illustrative Purposes Only.

mr
.steam®Installation & Operating Instructions
_________________________________________________________________
15
Care Tips for all Controls and Steamheads
1. Use only mild soap and water on a soft cloth to clean the control and steamhead.
2. Do not use abrasive cleansers
3. If the decorative cover is damaged on the iTempo®or iTempoPlus®
call MrSteam technical service for replacement parts.
NOTE: Replacement of the decorative covers requires removal and
reinstallation of the control from the mounting surfaces.
Warranty
To register your steam generator unit online and to review the MrSteam
Limited Lifetime Warranty please go to: blog.mrsteam.com/wr
mr.steam
temp
aroma chroma
time
Display
Up Key
Time Display/
Adjust Key
Down Key
Program Key
ChromaSteam
Key
Time Display/
Adjust Key
ON/OFF Key
AromaSteam
Key
Drawings for Illustrative Purposes Only.

Products, information and specifications are subject to change without notice.
For more information call Sales & Support at:
1.800.76.STEAM
(East Coast) 1.800.72.STEAM (West Coast)
2019 © Sussman-Automatic Corporation MrSteam and des., AromaFlo, AutoFlush, AutoSteam, Butler Package,
ChromaSteam, Clean Steam...Every Time, Club Therapy, Digital 1, Express Steam, From Bathroom to Spa, iDream Pack-
age, iGenie, iSizing, iSteam, MusicTherapy, Spa Package, Steam@Home, Steam Therapy, Sussman, Valet Package, Virtual
Spa System, Voice Genie and Voice Wizard are registered trademarks of Sussman-Automatic Corporation. AudioWizard,
HomeWizard, iButler, iTempo, iTempoPlus, Smart Sizing, SteamStart, The Intelligent Steambath are trademarks of
Sussman-Automatic Corporation. pur 100474A rev 10.19
mr
.steam®
Feel Good Inc.

!C A U T I O N
!C A U T I O N
mr.steam®STEAM HEAD
___________________________________________________________________________________________________________________________________________
I N S TA L L AT I O N I N S T R U C T I O N S
PUR 100421 10.15
mr
.steam®
Sussman-Automatic Corp® [email protected] www.mrsteam.com
43-20 34th Street, Long Island City, NY 11101 tel: 1 800 76 STEAM fax: [phone]
9410 S. La Cienega Blvd. Inglewood CA 90301 tel: 1 800 72 STEAM fax: [phone]
Steam
Supp y Pipe
End of pipe to be recessed
1/4" (without Acry ic Shie d)
1/8" (with Acry ic Shie d)
1/8" minimum c earance required
when Acry ic Shie d is used.
See insta ation instructions
provided with the Acry ic Shie d.
App y with si icone or
equa sea ant as required
for moisture sea .
Use Tef on
®
or equa
sea ant on pipe threads
Oi We
STEP 3
STEP 4
STEP 5
Steamhead
(shown with
optiona acry ic shie d)
Locating Nipp e
Drop Ear
Fitting
All drawings are for illustrative purposes only
3”
23/
4”
31/
2”
3”
1”
0 3”
7
/
8”
IMPORTANT: See the Installation and Operation Manual
provided with the steam generator for additional important
steamhead & control installation and operation information.
Installation: Steam Head (12" NPT)
INSTALLER: Because the steam head and direct
steam emissions are very hot, locate the steam head where incidental
contact by bather with the steam head or direct steam emission cannot
occur.
STEP 1 Locate steam head 6-12 inches above floor, except for:
1. Tub/shower enclosures, install 6 inches above tub top edge.
2. For enclosures with acrylic or other non-heat resistant
flooring install Acrylic Shield Part Number MS-103938.
3. To prevent door seals from deteriorating do not locate the steam
head where direct steam emission would contact door seals.
STEP 2
Install steamhead with the oil well facing up as shown. Hand
tightening is sufficient when teflon or equal pipe thread sealing com-
pound is used.
IMPORTANT NOTE: to preserve steam head finish, do not use
wrench or other tools to tighten. DO NOT use abrasive cleansers or
chemicals. Use only water with mild soap and a non-abrasive sponge.
Consult with supplier of acrylic, fiberglass and other
non-heat resistant enclosures for recommended steamhead location.
Use Acrylic Shield part number MS-103938. See instructions provided
with steam shield.
STEP 3 Secure a bronze drop ear fitting to a header and run a 1/2"
copper steamline from the steam generator to the drop ear fitting.
Install a temporary nipple (6" or longer)in the drop ear fitting to locate
the steamhead after the wall is finished.
STEP 4 After the wall has been finished, mark on the nipple where the
surface of the wall is. Remove the nipple and measure the portion that
was in the wall (the end to your mark). Subtract 14" from that dimen-
sion and select a brass nipple of that length to finish the installation.
STEP 5 Wrap teflon tape around the threads of the new nipple and
screw the nipple into the steamhead. Do not use wrenches or tools
which would damage the steamhead's finish. Wrap teflon tape around
the threads of the nipple and screw the nipple and steamhead assem-
bly you just made into the drop ear fitting in the wall. The steamhead
should be flush with the wall and the well must be facing up.

mr
.steam®Feel Good Inc.®
Installation, Operation and Maintenance Manual
Linear Steam Head
Residential Model: 144080
____________________
MP
_
O
_
RT
_
AN
_
T:_ Le
_
ave
_
th
_
is
_
ma
_
teri
_
al
_
wit
_
h t
_
he
_
ho
_
me
_
ow
_
ner
_
.
IMPORTANT: Leave this material with the homeowner.

READ ME FIRST!
As you follow these instructions, you will notice CAUTION
and IMPORTANT NOTE symbols. This information is
important for the proper, safe and trouble free installation of
the Linear Steam Head. These are types of potential hazards
that may occur if in-stallation instructions are not carefully
followed.
This signals a situation where injury or property damage may
occur if you do not follow instructions.
IMPORTANT NOTE: This highlights information that is
espe-cially relevant to a problem-free installation.
All information in these instructions is based on the latest
informa-tion available at the time of publication. Sussman-
Automatic Corpo-ration reserves the right to make changes
at any time without notice.
100561-1 Rev 3.20.1
mr
.steam
®
Sussman-Automatic Corp® [email protected] www.mrsteam.com
43-20 34th Street, Long Island City, NY 11101 tel: 1 800 76 STEAM
9410 S. La Cienega Blvd. Inglewood CA 90301 tel: 1 800 72 STEAM
Installation Section –Read Me First & Cautions
Linear Steam Head
1
®
®
Model 104480
PUR 103936 Rev 6.20
• Linear Steam Head model 104480 is suitable for MrSteam
generator models MS90 – MS400, MSSUPER1–
MSSUPER3, MX4 – MX6.
Do not use Linear Steam Head model 104480 for any
other MrSteam steam generator. Failure to follow these
instructions may result in a leak within the wall cavity and
cause problems associated with leaks, moisture and
property damage from leaks.
• Do not use the Linear Steam Head with any steam
generator that is not a MrSteam steam generator. Do not
locate the steam head in any location where the steam
emission zone is near a seat, bench or any space
occupied by any persons. Failure to follow these
instructions may result in a hazardous condition, scalding
or personal injury.
Using model 104480 for any steam generator model
larger than the MX6, or for any non MrSteam brand
generators may result in an improper installation or
hazardous condition.
• Do not use the Linear Steam Head with any NON-
MrSteam equipment or devices, including but not limited
to water softeners, steam generators, etc. Using the
Linear Steam Head with any NON-MrSteam equipment or
devices may result in personal injury or, Linear Steam
Head damage or property damage.
• MrSteam steam generators Models MX4, MX5 and MX6
require two 104480 steam heads. Failure to use two
steam heads may result in steam head operation where
incidental contact by the bather with direct steam
emission may occur. Do not locate the steam head in any
location where the steam emission zone is near a seat,
bench or any space occupied by any persons. Failure to
follow these instructions may result in a hazardous
condition, scalding or personal injury.
• Because the steam head and direct steam emission are
very hot, locate the steam head where incidental contact
by the user with the steam head or direct steam emission
cannot occur.
• Model 104480 Linear Steam Heads are for residential use
only. Do not use Model 104480 Linear Steam Heads for
commercial installations, Day Spa, or with commercial
steam generators. Using Model 104480 Linear Steam
Heads for commercial, Day Spa or installations with
commercial steam generators or any installation with
steam sessions exceeding 60 minutes a day, may result in
Linear Steam Head damage, property damage or
personal injury.
• Do not use any Linear Steam Head in any commercial
installation or with any commercial steam generator. Using
any Linear Steam Head in a commercial installation or
with any commercial steam generator may result in Linear
Steam Head damage, property damage or personal injury.
• Install in orientation shown in fig 2 only. Installation in any
other orientation may concentrate the steam and result in
excessive temperature. Failure to install in correct
orientation may result in steam head operation where
incidental contact by the bather with direction steam
emission may occur. Failure to follow these instructions
may result in a hazardous condition, scaling or personal
injury.
• Insulate the steam head and piping as required to reduce
temperature within the wall cavity. Do not locate the
steam head or plumbing near any materials, including
wiring, devices, or products that may be adversely
affected by elevated temperatures. Check with the
manufacturer of construction materials and products to for
suitability for operation at elevated temperatures. Failure
to follow these instructions may result in the failure of
materials, including wiring, devices, or products.