MSI GX630 - 001US - Athlon X2 2 GHz Installation instructions

GX630 （MS-1652）Disassemble SOP
■ 1、Battery Pack
■ 2、BOTTOM DOOR ASSY
■3、THERMAL-KIT And CPU Module
■ 4、RAM、WLAN And TUNER Module
■ 5、HDD Module ASSY
■ 6、ODD Module ASSY
■ 7、HINGE COVER ASSY
■ 8、UP CASE ASSY
■ 9、LOWER CASE ASSY
■10、LCD MODULE ASSY

GX630（MS-1652）Disassemble SOP
■ 1、Battery Pack
1-1：Push the battery Unlock button as below;
1-2：Push the battery Release button as below, then slide the battery pack out of the slot;
NO. Part Name Part No. Qty
1 Battery Pack S9N-0366200-SB3 1

GX630（MS-1652）Disassemble SOP
■ 2、BOTTOM DOOR ASSY
2-1：Remove 2pcs M2.5*5mm Screws ;
Note：Screw driver torque is 2.0~2.5kgf.cm
2-2：Remove Bottom Door Assy as below;

GX630（MS-1652）Disassemble SOP
2-3：Remove SIM Card Door as below;
NO. Part Name Part No. Qty
1Screw E43-1255001-G68 2
2 SIM CARD DOOR E2P-6510511-Y31 1
2BOTTOM DOOR ASSY 307-651J411-Y31 1

GX630（MS-1652）Disassemble SOP
■ 3、THERMAL-KIT And CPU Module
3-1：Remove 7pcs SPING Screws and 2pcs M2.5*5mm screws, Then Disconnect CPU Fan sink Cable;
Note：Screw driver torque is 2.0~2.5kgf.cm
24
3
1
9
7
5
8
6
3-2：Remove CPU Fansink;
NO. Part Name Part No. Qty
1 screw E43-1255001-G68 2
2 CPU FANSINK E32-1300112-F05 1

GX630（MS-1652）Disassemble SOP
3-3：Open CPU lock as below;
3-4：Remove CPU Module;
NO. Part Name Part No. Qty
1 CPU Module A10-K82G2F6-A08 1

GX630（MS-1652）Disassemble SOP
3-5：Remove 2pcs M2.5*5mm Screws;
Note：Screw driver torque is 1.8~2.0kgf.cm
3-6：Remove VGA Card Module;
NO. Part Name Part No. Qty
1 VGA CARD Module 602-V114-020 1
2 Screw E43-1255001-G68 2

GX630（MS-1652）Disassemble SOP
■ 4、RAM、WLAN And TUNER Module
4-1：Push RAM Slot Fastener as below;
4-2：Remove RAM Module;
NO. Part Name Part No. Qty
1 RAM Module S7C-S357701-T10 2

GX630（MS-1652）Disassemble SOP
4-3：Remove WLAN Card Antenna, Then Remove 1pcs M2*3mm Screw;
Note：Screw driver torque is 1.5~2.0kgf.cm
4-4：Remove WLAN Card Module;
NO. Part Name Part No. Qty
1 WLAN CARD Module S57-3800010-T46 1
2 Screw E43-1203007-G68 1

GX630（MS-1652）Disassemble SOP
4-5：Remove Tuner Antenna, Then Remove 1pcs M2*3mm;
Note：Screw driver torque is 1.5~2.0kgf.cm
4-6：Remove Tuner Module;
NO. Part Name Part No. Qty
1 TUNER Module S36-0000610-K45 1
2 Screw E43-1203007-G68 1