MSTRONIC MSE DIN-POE4S Series User manual

USER’S MANUAL
MSTRONIC CO., LTD.
MSE
DIN-POE4S
DIN-POE4D
4 Ports Gigabit PoE Injector

User’s Manual MSE DIN-POE4S/POE4D
MSTRONIC CO., LTD.
2
1. General Information
The DIN-POE4S and DIN-POE4D family is a DC/DC PoE (Power over Ethernet) In ector, provide
up to 4 different voltage DC input and four different voltage PoE output, output power maximum
35W/port (DIN-POE4D) or 1A/port (DIN-POE4S), data rate can be operating at 10M/100M/1000M.
The polarity of each PoE output can be reversed if you need to reverse the output polarity. This
manual will help you to install and setting the PoE in ector.
2. Hardware Description
Front panel detail
the port number is as the diagram shows.

User’s Manual MSE DIN-POE4S/POE4D
MSTRONIC CO., LTD.
3
Top panel detail
*LED Indicator
There are 4 LEDs on the front panel to indicate the input and output power status of each port.
LED STATUS Description
1~4 Green A valid power device is detected on this port.
Active current is 80mA.
Off For DIN-POE4S:
No valid input applied, the voltage is larger than 58VDC, or less
than 10.5VDC, or the output current over 2A limit.
For DIN-POE4D:
N
o valid input applied, the voltage is larger than 58VDC, or less
than 42.5VDC, or the output current over 0.684A limit.
*Data Input
The left ports 1-4 on the front panel are used for Gigabit Ethernet data input.
All four ports with surge protection.

User’s Manual MSE DIN-POE4S/POE4D
MSTRONIC CO., LTD.
4
*Power Input
The input voltage range of DIN-POE4S is 12VDC to 57VDC, and 44~57VDC for DIN-POE4D, they
are all common negative design, the green terminal (CON1) on top panel is used for power input
wiring, it can be connected to maximum 4 different sources with 4 different voltages, the umper A,
B, C, of JP9 on top panel controls the input/output connection, its setting as below. (1= umper on,
0=off)
Jumper
Input
A
(1-2)
B
(1-3)
C
(1-4) PoE Output
VIN1+ 1 1 1 PoE 1/2/3/4=VIN1
(Factory setting)
VIN1+
VIN4+
1 1 0 PoE 1/2/3=VIN1
PoE 4=VIN4
VIN1+
VIN3+
1 0 1 PoE 1/2/4=VIN1
PoE 3=VIN3
VIN1+
VIN3+
VIN4+
1 0 0
PoE1/2=VIN1
PoE3=VIN3
PoE4=VIN4
VIN1+
VIN2+
0 1 1 PoE1/3/4=VIN1
PoE2=VIN2
VIN1+
VIN2+
VIN4+
0 1 0
PoE1/3=VIN1
PoE2=VIN2
PoE4=VIN4
VIN1+
VIN2+
VIN3+
0 0 1
PoE1/4=VIN1
PoE2=VIN2
PoE3=VIN3
VIN1+
VIN2+
VIN3+
VIN4+
0 0 0
PoE 1=VIN1
PoE 2=VIN2
PoE 3=VIN3
PoE 4=VIN4

User’s Manual MSE DIN-POE4S/POE4D
MSTRONIC CO., LTD.
5
*PoE Output
The right ports 1-4 on the front panel are used for carry PoE output, the output voltage is the same as
input, no regulated. Normally as detailed below:
* Data pair A on line 1 and 2
* Data pair B on line 3 and 6
* Data pair C plus V+ on line 4 and 5
* Data pair D plus V- on line 7 and 8
*Output Polarity Re erse (for technician operation only)
The DIN-POE4S/POE4D may deliver PoE output with reverse polarity. Just move related umpers
from pin 1-2 to pin 2-3, and then
* Data pair C carry V- on line 4 and 5
* Data pair D carry V+ on line 7 and 8
Open the cover, the JP1~JP8 on the PCB responds for the output polarity of port 1~4, each two
umpers should be paired moved to ensure the path enough for the through current.
JP1 & JP2 JP3 & JP4 JP5 & JP6 JP7 & JP8
Control port Port 1 Port 2 Port 3 Port 4
* Pin1-2(short pin1 & pin2): RJ45 pair C (pin4 & 5) carry PoE positive voltage.
* Pin2-3(short pin2 & pin3): RJ45 pair C (pin4 & 5) carry PoE negative voltage.

User’s Manual MSE DIN-POE4S/POE4D
MSTRONIC CO., LTD.
6
4. Technical Information
Data Rate 10M/100M/1000M
Input voltage: 12VDC to 57VDC (DIN-POE4S)
44 VDC to 57VDC (DIN-POE4D)
Maximum PoE power 35W/port (DIN-POE4D)
Current limited – 1A/port (DIN-POE4S)
Compliance 802.3af/at (DIN-POE4D)
PoE protection over-current, over/under voltage
LEDs: Green-Power ready, Off-No power apply
Operating temperature -40℃~ +75℃
Operation humidity 90% relative humidity, non-condensing
Storage temperature -40℃~+85℃
Dimension 125mm(H) x46mm(W) x102mm(D) DIN RAIL Mountable
Surge protection on data input ports:
Signal
Operating Voltage Data 5V
Clamping Voltage
Data 16.5V (@I PP =5A, t p =8/20µs, I/O pin to GND)
Peak Pulse Current 20A (tp=8/20µs)
Pin Protected All 8 pin protected
Max. Shut Capacitance <3pF (VR = 0V, f = 1MHz, I/O pin to GND)
< 1.5 pF (VR = 0V, f = 1MHz, Between I/O pins)
IEC COMPATIBILITY (EN61000-4)
IEC61000-4-2 (ESD) ±15kV (air), ±8kV (contact)
IEC61000-4-4 (EFT) 40A (5/50ns)
IEC61000-4-5 (Lightning) 20A (8/20µs)