MSTRONIC PSE-SW5F-ST User manual

PSE-SW5F-ST
PSE-SW5F-SC
PSE-SW5F-SFP
USER’S MANUAL
MSTRONIC CO., LTD.
MSE PSE-SW5F Series
Power Source Equipment
(Power over Ethernet Switch)

User’s Manual MSE PSE-SW5F-ST/-SC/-SFP
MSTRONIC CO., LTD.
2
1. General Information..............................................................
2. Hardware Description...........................................................
LED Indicators......................................................................................
Power Wiring……………………………………………………………….
Ethernet Port Wiring……………………………………………………….
Fiber Port Wiring...................................................................................
PD Port Wiring…………………………………………………………….
3.Model Information........................................................
4. Technical Specification........................................................
3
3
3
5
7
8
9
11
12

User’s Manual MSE PSE-SW5F-ST/-SC/-SFP
MSTRONIC CO., LTD.
3
1. General Information
The PoE (Power Over Ethernet) Switch supports four Fast Ethernet ports with PoE injector plus one
100Base-FX up-link port. The switch provides Power over Ethernet functions to deliver 35Watts of
power budget per port to a powered device(PD), which is in compliance with IEEE802.3af/at
standard to deliver both Ethernet data and DC48V power through the traditional UTP or STP cable
to a PD. This manual will help you install and maintain the PoE switch. Installation of the PoE
switch is very easy and it will begin to operate as soon as you have powered it up.
2. Hardware Description
*LED Indicator
There are 10 LEDs on the PoE switch to indicate the power and operational status. The following
section describes the functions of each LED indicator.
Front panel detail
For PSE-SW5-ST:
PoE Link/Act
Indicator Indicator
For PSE-SW5-SC:
PoE Link/Act
Indicator Indicator

User’s Manual MSE PSE-SW5F-ST/-SC/-SFP
MSTRONIC CO., LTD.
4
For PSE-SW5-SFP:
PoE Link/Act
Indicator Indicator
*POWER Indicator
LED
STATUS Description
Power
(PWR)
Green
LED ON if power input has valid power
apply.
Red
LED ON if the following condition
happens.
*Power input under voltage (Vin<10V)
*Power input over voltage (Vin>59V)
*PoE over current(2.5A/per port)
The indicator is used in current mode
only.
Off No power in DC input
LINK/ACT

User’s Manual MSE PSE-SW5F-ST/-SC/-SFP
MSTRONIC CO., LTD.
5
*SWITCH Indicator (the right LED of RJ-45)
LED STATUS Description
P1~P5
Link/Act
Green A network device is detected, but no
communication activity is detected.
Blinking
@43ms
This port is transmitting to, or receiving
package from another device at 100Mbps.
Blinking
@120ms
This port is transmitting to, or receiving
package from another device at 10Mbps.
Off No device is detected.
*PoE Indicator (the left LED of RJ-45)
LED STATUS Description
P1~P4
PoE
Yellow A valid Powered Device(PD) is detected
and delivering power on this port.
Off No PD is detected on this port.
*Power wiring
The PoE switch family includes 3 models, be used for 3 different ranges of input voltage as,
Current mode full range voltage (10 to 57VDC)
24V-802.3at mode 24VDC typical(12 to 36VDC)
48V-802.3at mode 48VDC typical(40 to 57VDC)
In current mode, please make sure the input current don’t over 10Aand make sure the input current
don’t over 2Amp.

User’s Manual MSE PSE-SW5F-ST/-SC/-SFP
MSTRONIC CO., LTD.
6
For PoE (PSE) operation, the input voltage must be in the range of -42 to -60 VDC. Otherwise, the
switch will function only as an Ethernet switch but will not provide any PoE power output. For PoE
operation, make sure your 48 VDC supply is rated for at least 75 Watts for 4x 802.3af PoE port, or
150W for 4x 802.3at PoE port, plus some overhead for the switch.
The PoE PSE ports will deliver DC power over the spare pairs as the connection:
* TX on lines 1 and 2
* RX on lines 3 and 6
* V+ on line 4 and 5
* V- on line 7 and 8
Rear panel terminal block wiring detail:
*Ethernet Port Wiring
The PoE Switch supports Port 1 to Port 4 with automatic MDI/MDI-X crossover, autosense of the
speed and duplex for 10Base-T or 100Base-TX connections. Automatic MDI/MDI-X crossover
allows you to connect to other devices (switches, hubs, or workstations etc..), without regard to
using straight-through or crossover cabling.
Port 1 to port 4 also provides Power over Ethernet function which delivers DC48V power through
the spare pairs (pair 4,5 and pair7,8) to the PD.

User’s Manual MSE PSE-SW5F-ST/-SC/-SFP
MSTRONIC CO., LTD.
7
The following tables depict the wiring diagram of straight-through and crossover cabling. The
crossover cables simply cross-connect the transmit lines at each end to the receive lines at the
opposite end.
Straight-through Cabling
Pin 1 Pin 1
Pin2 Pin 2
Pin3 Pin 3
Pin6 Pin6
Cross-over Cabling
Pin 1 Pin 3
Pin 2 Pin 6
Pin 3 Pin 1
Pin 6 Pin 2

User’s Manual MSE PSE-SW5F-ST/-SC/-SFP
MSTRONIC CO., LTD.
8
Connect an Ethernet cable into any switch port and connect the other side to your attached device.
The green Link/Act LED will light up when the cable is correctly connected. Refer to the LED
indicator section for descriptions of each LED indicator.
If a port LED is off, go back and check for connectivity problems between that port and the network
device it is connected to.
The maximum cable length for 10/100BaseT with Cat 5 twisted pair cables is
typically 100 meters (328 ft.).
Fiber port wiring
The PoE switch(fiber mode) has one 100 Mbps (100Base-FX) multi-mode or single-mode fiber port.
The maximum segment length is dependant upon the type of fiber optic transceiver installed in the
switch. Refer to the technical specifications for details. Or contact a sales agent for the available
fiber optic transceivers(Model NO.:MSE PSE-SW5F-ST or PSE-SW5F-SC or PSE-SW5F-SFP).
The automatic MDI/MDI-X crossover function does not apply to fiber connections. To connect the
fiber optic port on one switch to the fiber optic port of another switch, simply cross-connect the
transmitter at each end to the receiver at the opposite end as illustrated in the figure below.
The corresponding ACT/LNK LED will be ON state when you have made a proper connection.
Fiber cable wiring (SC to SC):

User’s Manual MSE PSE-SW5F-ST/-SC/-SFP
MSTRONIC CO., LTD.
9
*PD Port Wiring
Port 1 to port 4 provides PoE inject functionality with a maximum 35W ability to power up the
powered device using the straight-through or cross-over Ethernet cable.
The PoE switch follows the IEEE802.3af Alternative B mode connector assignment. The following
table shows pin assignments of alternative A and B for the Power Source Equipment.
Conductor
Alternative A
(MDI-X) Alternative A (MDI)
Alternative B
(All)
1Negative Vport Positive Vport
2 Negative Vport Positive Vport
3 Positive Vport Negative port
4 Positive Vport
5 Positive Vport
6 Positive Vport Negative Vport
7 Negative Vport
8 Negative Vport
Be sure the twisted pair cable is bound with the standard RJ-45 pin, especially pins 4, 5, 7 and 8.
If the RJ-45 is bound with the wrong pin number, the PoE switch will not recognize the PD and
won’t deliver DC48V power to PD. The yellow PoE LED will light up when the cable is correctly
connected. Refer to the LED Indicator section for descriptions of each LED indicator. If a port
LED flashes, go back and check for connectivity problems between that port and the network
device it is connected to.

User’s Manual MSE PSE-SW5F-ST/-SC/-SFP
MSTRONIC CO., LTD.
10
3. Model Information
Model
Input Voltage
Output voltage
802.3af/at
PSE-SW5F-ST-S
PSE-SW5F-SC-S
PSE-SW5F-SFP-S
(current mode)
10-57VDC 10-57VDC
(non-regulated) No
PSE-SW5F-ST24
PSE-SW5F-SC24
PSE-SW5F-SFP24
(24V-802.3at mode)
12-36VDC 56VDC
(regulated) Yes
PSE-SW5F-ST48
PSE-SW5F-SC48
PSE-SW5F-SFP48
(48V-802.3at mode)
40-57VDC 40-57VDC
(non-regulated) Yes

User’s Manual MSE PSE-SW5F-ST/-SC/-SFP
MSTRONIC CO., LTD.
11
4. Technical Specifications
Standards IEEE802.3/IEEE802.3u standards
(10Base-T/100Base-T/100Base-FX)
Ports 4 ports with 4 PoE(PSE), supports auto-crossover &
auto-polarity, 1 port with the fiber connector
Transmission speed 100Mbps(100Base-T), 10Mbps(10Base-T) Auto-negotiation
Switch technology store-and-forward
Protocols CSMA/CD
Flow control IEEE802.3x(full-duplex),back pressure(half-duplex)
Data transmission rate 148800pps for 100Base-T, 14880pps for 10Base-T
Address table 1K MAC address table, self-learning
Connector RJ-45, SC or ST or SFP connector (for fiber optic port)
Note(SFP): Fast Ethernet 100 Base-FX Complaint Slot for standard SFP transceiver
(Duplex LC Connector)
Fiber optic port
*Fiber optic port: ST/SC/SFP
*Port speed 100Base-FX(100Mbps),full duplex
*Wave length 1310nm
*Max TX power -14dBm(mm), -8dBm(sm)
*Min TX power -19dBm(mm), -15dBm(sm)
*Min RX sensitivity -32dBm
*Max RX power -14dBm(mm),-8dBm(sm)
*Link budge 13dB(mm),17dB(sm)
*Fiber multi-mode(mm) typical 50 or 62.5/125um
*Fiber single-mode(sm) typical 9 or 10/125um

User’s Manual MSE PSE-SW5F-ST/-SC/-SFP
MSTRONIC CO., LTD.
12
*Fiber max. distance 2km(mm),15km(sm)
Note: Other fiber connector and transmission distance are available.
PoE port Port 1-4, auto power management
Pin assignment: TX(1,2), RX(3,6), V+(4,5), V-(7,8)
Maximum PoE power Per port 35W
PoE disconnect mode DC disconnect
PoE auto detection IEEE802.3af/at
PoE protection Over-temperature, over-current, over/under voltage
LEDs *Link/Activity (Green ON/ Green Blinking every 43ms @100Mbps/
Green Blinking every 120ms @10Mbps)
*PoE(Yellow) On-PD detect, Blinking-error detect)
*POWER Green-normal, Red-alarm
Power input Current mode:10 to 57VDC
24V-802.3at mode:12 to 36VDC
48V-802.3at mode:40 to 57VDC
Power consumption 5W without PD loading
Operating temperature -20℃~ 85℃
Operation humidity 90% relative humidity, non-condensing
Storage temperature -55℃~+105℃
Dimension 40mm(H)x118mm(W)x159mm(D)