MTX iT1air User manual

mtx.com - mtxaudio.eu
iT1air
Ultimate Apple®AirPlay®Lightning®Hifi
Powerful Compact System with Exceptional Bass Extension.

1. Connect the iT1air to the wall outlet. Switch on the unit - press“Power” once - and wait 10 seconds for initialization.
2. Verify your iPhone, iPad or iPodTouch is connected to theWi-Fi network you want to join.
3. Connect your device to the Dock (LED#2 red) or to the USB (LED#2 green).
4. Push theWi-Fi control once.The unit will display a message on your iDevice asking if you want to share yourWi-Fi settings
with the iT1air. Accept. The iT1air is now available in theWi-Fi network.The LED#1 should be solid Blue. You can now disconnect your
device from the iT1air.
5. Use your computer or iDevice and open“iTunes”or“Music”. In the Airplay devices list, choose“MTX iT1air” and hit play to start
listening to music.
Owner’s Manual - MTX iT1air
What’s In the Box ?
iT1air Placement and Installation :
Quick Start with Airplay :
LED Status Summary :
Thank You !
Thank you for purchasing the MTX iT1air high-end, high-definition audio system. The iT1air is designed to deliver a deeper dimension
that brings your music to life. No other system provides the exacting measure of clarity in such a small enclosure. Whether you are
listening from your iPad, iPhone, iPod or computer, the iT1air delivers outstanding sound quality. The iT1air is your new favorite Hi-Fi
system. Congratulations for making a smart choice and enjoy the ultimate audio experience with MTX.
1. The iT1air unit. Use caution when unpacking as the unit is heavy.
2. IR remote control. Batteries are not included.
3. Wi-Fi antenna to be connected to theWi-Fi socket on the back of the unit.
4. Two power cords. One for the European plug (CEE 7/16 Type C and one for the United Kingdom plug (BS 1363 Type G).
5. The owner’s manual.
The location of your iT1air in the room is crucial for sound quality and bass level.The unit is equipped with two side subwoofers and
is able to reproduce very low frequencies. Some guidelines should be followed to get the best possible result.
1. Install the unit at an equal distance between the two side walls to get the largest possible staging.The side walls will act as
reflectors.
2. If you reduce the distance between the unit and the back wall, the bass level will rise. If you increase the distance, the bass level
will decrease. Choose distance based on your preference.
3. Your ears and the iT1air should be in the same horizontal plane for perfect definition.
4. To get the best possible result, do not put the unit on a table with a large panel in front of the speakers as it will reflect the sound
in an undesireable way.
5. Adjust the subwoofer level with the remote control.
Left - LED#1 :
• Flashing Blue: Looking for theWi-Fi network
• Solid Blue: Hooked to theWi-Fi network
• Flashing Red: Remote control feedback
• Flashing Blue/Purple:Wi-Fii setting mode
Right - LED#2 :
• Solid Blue : Airplay input selected
• Solid Red : Dock input selected
• Solid Green : USB input selected
• Solid Purple : AUX input selected

Press for Airplay input -The LED#2 turns blue.
Press for Dock input - The LED#2 will turn red.
Press again for USB input - The LED#2 will turn green.
Press for Jack Aux Analogue input - The LED#2 will turn purple.
Main Unit Controls
LED#1 : Wi-fi Status and Remote Feedback.
LED#2 : Input Indicator.
Back of the unit
Main Unit Controls
When you switch on the unit, the LED#1 will slowly flash blue looking for theWi-Fi network. It will continue to flash Blue until the network is set.
When the unit is connected to your network, the LED#1 will turn to solid Blue.
When you press any control on the IR remote control, the LED#1 will flash red/blue to indicate that the connection is done.
• Single press will power On or power Off the unit. When the unit is Off, the two LEDs willnot be illuminated.
When the Unit in On, the two LEDs will be illuminated. LED color will depend on the input and settings.
• Press and hold for 5 seconds to reset the unit’s sound settings (volume and subwoofer level to zero).
• Single press will decrease the volume one step - The LED#1 will flash red once.
• Press and hold will decrease volume gradually -The LED#1 will flash red continuously.
• Single press will increase the volume one step - The LED#1 will flash red once.
• Press and hold will increase the volume gradually -The LED#1 will flash red continuously.
• Single press will enable Airplay mode -The LED#2 will turn Blue.
• Press and hold for 5 seconds will enable theWi-Fi direct mode, the unit will turn into a router and you’ll be able to
stream from your Airplay device directly to the unit without any external network.
• First single press will enable dock input -The LED#2 will turn Red
• Second single press will enable USB input -The LED#2 will turn Green
• Single press will enable the jack input -The The LED#2 will turn Purple.
• Single press will copy theWi-Fi settings of your wired device to the unit.The unit will be available on the same
network as your device.
• Press and hold for 5 seconds will turn the unit toWi-Fi settings mode -The LED#1 will flash Blue/Purple. See section
«HowTo : Connect to the network for Airplay #2» for more details.
Volume Up
Volume Down
Source : AirPlay
Direct mode
Power On/Off
Reset
Source Select :
Dock - USB
Source Select :
Anologue Jack
Wi-fi Connection
Settings Mode

Lightning Dock & Compatible Devices
Wifi Antenna Connector.
AUX Analog 3,5mm Jack Input.
Apple® USB Input.
AC Power Socket.
IR Remote Control.
Put one of the following devices in the Lignhtning dock. Press till the LED#2 turns to red. Launch Music and push play. Enjoy
the tunes stored on your device.
Screw the included wifi antenna here for optimal Airplay® performances.
Connect your iT1air to the power supply. Use the included power cord.
The unit is compatible with 100~120V / 220~240V AC, 50~60Hz. You don’t need to move any switch, the selection is automatic.
Before using the remote control, you must install two AAA batteries. Remove the bottom panel with a 2mm HEX key. Follow the (+)
and (-) signs located around the two springs. See“How To : Install the Batteries in the Remote Control”on the next page.
Use this input with stereo analog signals from a TV, a Blue Ray/DVD/CD player, an MP3 player, a Tablet, a cellular phone, etc.
Do not forget to press “AUX input” to activate the AUX Analog jack input. The LED will turn purple.
Do not forget to press once or twice to activate the USB input.The LED will turn green.
USB works with iPhone 5, iPhone 5C, iPhone 5S, iPhone 4S, iPhone 4, iPhone 3GS, iPhone 3G, iPhone, iPad air, iPad (3rd and 4th
generation), iPad 2, iPad, iPad mini, iPod touch (1st through 5th generation), iPod classic, and iPod nano (1st through 7th generation).
The Aplle devices not listed here are still compatible. But they’ll have to use the USB input (see )
Skip Back/Browse Left
Volume Down
Source Select : AirPlay
Stand By On/Off
OK
Menu/Browse Back
Subwoofer vol. Down
Skip Forward/Browse Right
Browse Down
Browse Up
Volume Up
Source Select : Dock & USB
Source Select : Aux (Jack)
Subwoofer vol. Up
Play/Pause
Owner’s Manual - MTX iT1air

IR Remote Control Behavior.
• A single push will power On or power Off the iT1air. When the unit is Off, the two LEDs will be Off.
When the Unit in On, the two LEDs are on. LEDs colors depend on the input and wifi settings.
• A single push will enable Airplay Input -The LED#2 will turn to solid Blue.
• Press and hold for 5 seconds will enable the DirectWi-Fi mode and you’ll be able to stream from your computer, from
iTunes or from your Airplay device directly to the unit without any external network. The iT1air will create the network.
• First push will enable Dock input - The LED#2 will turn to solid Red.
• Second push will enable USB input - The LED#2 will turn to solid Green.
• Single push will enable the Aux Analogue 3,5mm jack input - TheThe LED#2 will turn to solid Purple.
• Single push will increase the volume one step -The LED#1 will flash red twice.
• Press and hold will increase the volume gradually -The LED#1 will flash red continuously.
• Single push will decrease the volume one step -The LED#1 will flash red twice.
• Press and hold will decrease volume gradually -The LED#1 will flash red continuously.
• Airplay, Dock & USB : Single press will navigate to the top - The LED#1 will flash red twice.
• Airplay, Dock & USB : OK/validation - The LED#1 will flash red twice.
• Airplay, Dock & USB : Single push will navigate to the bottom. The LED#1 will flash red twice.
• Single push : Skips to the next track on the iDevice or in iTunes - the LED#1 will flash red twice.
• Press & hold : Fast backward in the current track - the LED#1 will flash red continuously.
• AirPlay, Dock & USB : Browse the iDevice : move to the left - the LED#1 will flash red twice.
• Single push : Skips to the next track in the iDevice or in iTunes - the LED#1 will flash red twice.
• Press & hold : Fast forward in the current track - the LED#1 will flash red continuously.
• AirPlay, Dock & USB : Browse the iDevice : move to the right - the LED#1 will flash red twice.
AirPlay, Dock & USB : Play/Pause -The LED#1 will flash red twice.
AirPlay & USB -> Browse back the iDevice. It is the same behavior as Apple’s «Menu» - the LED#1 will flash red twice.
• Single push : increase the subwoofer volume one step - the LED#1 will flash once.
• Press and hold increase the subwoofer volume gradually - the LED#1 will flash fast.
• Single push : Decrease the subwoofer volume one step - the LED#1 will flash red once.
• Press and hold decrease the subwoofer volume gradually - the LED#1 will flash red fast.
Source : AirPlay
Direct mode
Power On/Off
Reset
Source :
Dock - USB
Volume Up
Subwoofer
Volume Up
Subwoofer
Volume Down
Volume Down
Browse UP
Browse Down
Skip Backward
Browse Left
Skip Forward
Browse Right
Play / Pause
Browse Back / Menu
OK
Source Select :
Aux (Jack)

Owner’s Manual - MTX iT1air
How To : Connect to the network for Airplay #1 : 5 sec...
How To : Connect to the network for Airplay #2 : Geek...
1. Connect the iT1air to the wall outlet. Push“Power” to switch on the unit and wait 10 seconds for initialization.
2. Take your iPhone, iPad or iPod Touch and verify it is connected to the Wi-Fi network.
3. Connect your device to the Dock (LED#2 red) or to the USB (LED#2 green).
4. Push once. The unit will display a message on your iDevice asking if you want to share yourWi-Fi settings with the iT1air.
Accept.The iT1air is now available in theWi-Fi network. The LED#1 will illuminate solid Blue. You can disconnect your device now.
5. Open a computer or you iDevice and in the Airplay devices list, choose “MTX iT1air”.
1. Connect the iT1air to the wall outlet. Push to switch on the unit and wait 10 seconds for initialization.
2. Press and hold (Wifi control) for 5 seconds. The LED#1 will flash Blue/Purple.
3. Take your computer, your iPad, your iPhone, your iPod touch or any Android tablet and look for the iT1 wifi network.
4. Join the network named“MTX iT1air”.
5. Open a web browser and type 192.168.1.1 -You are now on the iT1air setting page (see picture below).
6. Choose your network in the list and type your password.
Note : at the bottom of theWifi networks list, you can configure it manually, if the network is hidden for example.
7. Hit“Apply”. The unit will restart and join the chosen network.
8. Open a computer or your iDevice. In the Airplay devices list, choose the“MTX iT1air”. Hit play... Music...

How To : Change “MTX iT1air“ in the Airplay list.
How To : Reset the subwoofer level.
How To : Reset the unit.
How To : Switch on the Wifi Direct mode.
How To : Stay Tuned.
You can change the unit wifi name if, for example, you have more than one iT1air in the same network.
1. Connect the iT1air to the wall outlet. Push“Power” to switch on the unit and wait 10 seconds for initialization.
2. Press and hold “Wi-fi” for 5 seconds.The LED#1 will flash Blue/Purple.
3. Take your computer, iPad, iPhone, iPodTouch or any Android tablet and look for the iT1 Wi-Fi network.
4. Join“MTX-iT1air-network”.
5. Open a web browser and type 192.168.1.1 -You are now on the iT1air setting page.
6. Type the new desired name in the“AirPlay Device Name field.
7. Hit“Update”. The unit will restart. It will be available in the Airplay devices list under the updated name.
The subwoofer level is adjustable from -5dB to +10dB by 1dB steps.
If you want to go back to 0dB, just push (Sub-) and (Sub+) at the same time on the remote control.
Do not abuse the level of the subwoofers. Too much bass will affect sound quality and add distortion.
You can reset the volume and the subwoofer settings.
Press and hold for 5 seconds“Power” on the unit or on the remote control.
If no Wifi network is available, the iT1air can generate his own wifi network for Airplay.
Press and hold for 5 seconds the Airplay control (on the Unit or on the Remote) will enable the Wifi Direct mode.
The name of the network (SSID) is « MTX iT1air» . The unit will turn into a router and you’ll be able to stream from your
Airplay device directly to the unit without any external network.
https://www.facebook.com/MTXEurope
https://twitter.com/MTXEurope
http://www.mtxaudio.eu
Remote
Press and hold
for 5 seconds.
Press and hold
for 5 seconds.
How To : Install the Batteries in the Remote Control.
Before using the remote control, you must install two AAA batteries.
Remove the bottom panel with a 2mm HEX key. Follow the (+) and (-) signs located around the two springs.
AAA
AAA

Designed and Engineered by MTX in Phoenix - AZ, USA.
© 2014 Mitek. All rights reserved.
MTX is a registered trademark of Mitek.
Due to continual product development, all
specifications are subject to change without notice.
Mitek - MTX
4545 East Baseline Rd. Phoenix, AZ 85042, USA
MTX is proud to be an American Audio Company since 1971.
https://www.facebook.com/MTXEurope
https://twitter.com/MTXEurope
http://www.mtxaudio.eu