Multi Nautic QP-400 User manual

Multi
NAUTIC®
STATIONARY DOCK
QP-400 Model
(# 21011)
Assembly guide
Toll-free help line : 1-800-585-1237 l[email protected]
Congratulations
On Your New Dock !

REQUIRED MATERIALS:
- 10 cedar planks: nominal size: 5/4 in. x 6 in. x 8 ft. (actual: 1 in. x 5,5 in. x 8 ft.)
actual size: 25 mm x 144 mm x 2.43 m
> 8of the planks to be cut into 16 planks of 118.6 cm (46 11/16 in.) each. Read STEP 7.
Note: both end planks must be cut to fit around leg holders. See image beside.
> 2boards to be kept full length 2.43 m (8 ft) for decking supports.
- 70 1 ¾in. #8 wood screws
TOOLS NEEDED:
- 3/4 in. and 7/16 in. wrenches
- Star screwdriver
- Cordless drill with
1/2 in. and 9/64 in. drill bits
+ #2 square bit
- Sledgehammer
DOCK SIDES
(2)
END
PIECES
(2)
CENTRAL
SUPPORT
(1)
GALVANIZED STEEL
POSTS
(2)
BASE PLATES
(2) JUNCTION
PLATES (2) ADAPTORS
BOLTS INCLUDED
(1 OF EACH)
BOLT KITS
1/4 in. x 5/8 in. (8)
1/4 in. x 1 1/4 in. (16)
BOLTS
1/2 x 1 in.
(8)
PVC CAPS
(2)
THE QP-400 CONTAINS:
INSTALLATION REQUIREMENTS
• Afixed dock is ideally suited for water depths under 1.3 m (4 ft).
• Afixed dock is not made to withstand pressure or tension caused by moored boats in agitated waters. We recommend
separated mooring systems; deadman blocks, chains and mooring buoys.
• In rough condition areas, or if piles are used to their full lengths, you should increase the dock's stability by adding
diagonal braces to the posts (item # 22034).
• Have two strong adults to assemble frame. Install decking while on solid ground, then bring dock to water to install on piles.
SAFETY FIRST
Our MULTINAUTIC®team of professionals has designed and engineered the best lightweight aluminum dock available.
Please read these instructions before assembling your new dock, to ensure that assembly is done safely and correctly.
• All bolts and nuts are tightened securely before using your new dock.
• DO NOT modify this dock system, as alterations or welding can weaken the structure and will void the warranty.
• Always wear personal safety protection such as safety glasses, work gloves and boots.
• Keep children and pets clear of work area during assembly.
• Weight capacity of this dock structure will not support vehicles of any kind and is limited to 4 people or 363 kg (800 lbs).
• DO NOT use corded electrical tools in or near water.
MAINTENANCE AND STORAGE
ALUMINUM FRAME: There is no maintenance required on the aluminum frame itself. Due to air and water exposure, a
light tarnish may appear. Simply rub the frame with a Scotch Brite™style pad to remove light scratches, though tarnish
or light scratches will not affect the strength or integrity of the dock.
WOOD DECKING: –Important–Your aluminum frames should never come in contact with green treated wood. We highly
recommend cedar, which is light and maintenance-free, and that you refer to your wood supplier if you want to apply a
protective product.
Never leave post docks in the water in wintertime because of ice movements. When storing the docks, leave the decking in
the aluminum structure. You may store them flat (upside down to prevent fading under the sun) or straight on their sides.
A
LATERAL &
CORNER ADAPTOR
PARALLEL
ADAPTOR
CORNER
TO REDUCE SPACE BETWEEN DOCKS,
YOU MAY SCREW A 2
in. x 4 in.
( 44 mm x 95 mm) WOOD BOARD ON A SIDE.
UNSCREW BOLTS OF THE
DOCK WITHOUT LEG PILES TO
LIMIT DOCK MOVEMENTS.
SIDE
B
SEE NOTE
BELOW
B
A
NOTE: YOU WILL NEED TO REDRILL THE 2 DOCK’S HOLES B WITH
1/2 in. DRILL BIT IN ORDER TO INSTALL THIS LATERAL ADAPTOR
AND USE THE 1/2 in. x 1 in. BOLTS SUPPLIED WITH THE PART.
© Copyrights Multinautic®2020
5.7 cm
(2 1/4 in.)
3.8 cm
(1 1/2 in.)
USE THE 2 in. LONG BOLTS
SUPPLIED WITH THE ADAPTOR

DECKING SUPPORTS
7
30 cm
(12 in.)
30 cm
(12 in.)
30 cm
(12 in.)
30 cm
(12 in.)
STEP 2 Insert and bolt in the 2 end pieces with 1/4 in. x 1 1/4 in. bolts by hand (longer part
of leg holder on top). You can now tighten all assembly bolts (BEWARE, aluminum is soft –
DO NOT over-tighten).
STEP 3 Apply grease on the threads of the 1/2 in. x 1 in. bolts and install them in 2 end
corners.Slideinlegpilestorequiredheight, buttightenonlylightly asyouwillneed toreadjust
once in water. Install junction plates to the dock end opposite to posts.
STEP 4 Install base plates on leg piles, leaving approximately 15 cm (6 in.) under the plate
(a little more is required for soft lake bottoms, a little less when lake bottom is very hard).
Tighten securely.
STEP 5
Before installing decking, check squareness of the structure once again so that
118.6 cm (46 11/16 in.) decking planks will easily insert in openings at both ends and in the middle.
DECKING ASSEMBLY
DOCK FRAME ASSEMBLY
STEP 1 P lace the 2 side extrusions on a flat
surface (decking support lip on top). Insert central
support with 1/4 in. x 5/8 in. bolts. Be sure there are
2,5 cm (1 in.) from top of support lip to top of square
tube.For now, tightenbolts byhand. Finaltightening
will be done when assembly is complete.
8
2nd section and the following
ones shown here
(the first dock section doesn’t
need junction plates)
STEP 6 Once the dock frame assembly is put together, install it at about the height of a table with 4 leg piles, checking
the squareness of the structure by taking an “X” measurement from corner to corner. The dimension should be the same
as +/- 4 mm (1/8 in.). If the measurements differ push on the longest part of the frame in order to correct and make sure
that they
remain as is when assembling the decking. If the structure doesn’t keep its square shape, tip it on the side and push
in one of the corners.
STEP 7
Install the planks with the smooth (best) side down flush into the dock side support lips (you will assemble the
deckingpanel upsidedown in orderto facilitateyour work andyou’ll flipit back later). Alignall onone side ofthe dock,and
leave an equal space between each board (approximately 1 cm (3/8 in.) between each plank). You may use 17 decking
boards instead of 16 for smaller gaps between boards as Multinautic®'s Cedar Decking Kit, #21175.
STEP 8 Once all is positioned flush on one side, place the two 2.4 m (8 ft.) decking support planks at about 30 cm
(12 in.) from the sides and screw in place. You should pre-drill the supports with 9/64 in. bit to prevent cracking. Ensure
that no spaces are created between wood supports and decking boards when adding the screws.
STEP 9 Once your panel is completed, flip it over and centre it equally on each side. Drill six 9/64 in. holes and screw
the panel at both ends and in the middle.
A
B
C
B
pushpush
69
1.2 m x 2.4 m
(4 ft x 8 ft) 1
2
3
4
INSTALLATION
Laythefirstdocksectiononyourshore,‘postless’endongroundand‘posts’endinwater. Poundpostssothebaseplates
properly sit into lake bottom. Using the upper bolts on the leg holders, adjust the dock to desired height. Bottom bolts will
be used to set the other dock section. Repeat to complete your dock layout.Adistance of about 35 cm (14 in.) with water
is recommended. If desired, cut the top part of your leg piles to the same height (keeping in account seasonal water
fluctuation), then add PVC caps.
1
2
34
25 mm
(1 in.)

Quality Accessories for your
QP-400 Post Dock :
Limited warranty
Flip-up Dock Ladder Kit
Turnsa ladder intoa flip-up so you can
take it out of the water when needed.
Designed for our dock ladder #15524.
Will need modifications if added to
another ladder model.
15529
4-step Aluminum Dock Ladder
- Large 44 cm x 12.7 cm (17 1/4 x 5 in.)
deep step with plastic endcaps
- Nice 3.8 cm (1 1/2 in.) aluminum handrails
- Clean and sturdy: will support a 113 kg
(250 lb) load
- Stainless-steel assembly hardware included
- Compatible with additional step(#15528)
and flip-upkits.
Includes 3 easy-to-assemble sections:
2 handrails and 1 step section
Step-by-stepinstallation guide in the box.
15524
White PVC Bumper
Non-marking premium PVC.
UV and fungus protection treatment.
Prevents damage to boats during docking.
Long lasting. Easy care and cleaning.
Small P shape
Three 2.44 m (8 ft) lengths
Small D shape
Two 4.88 m (16 ft) rolls
10520
Corner Pile Bumper
To be installed on leg pile at the end corners
of the dock to protect boats from contact
with the metal dock pipe and hardware at
dock level.
Rests securely against the dock.
Has an inflation valve to adjust firmness.
18 cm x 43 cm (7 x 17 in.)
15014
Multinautic® hereby warrants to the original consumer
purchaser only that this product will be free, in normal use,
of any defects in materials and workmanship for a period of
one (1) year from the consumer's original date of purchase
directly from Multinautic® or from a Multinautic®
authorized reseller. At its sole option, Multinautic® will
repair or replace the defective product and promptly return it
to you. In order for this warranty to be valid, the consumer
must, at the time the product is returned, provide proof of
purchase in the form of the original purchase receipt directly
from Multinautic® or from a Multinautic®-authorized
reseller. If Multinautic® elects to replace the defective
product, then Multinautic® reserves the right to replace the
defective product with another product of the same model or
a model of at least comparable quality and features in
Multinautic®'s sole determination. A reimbursement cannot
exceed the amount paid by the customer and is limited
to the replacement of the defective product.
If you believe this product is defective within the warranty
period, call Multinautic®for a Return Authorisation Number
(RAN), carefully repack the unit, insure it and return it with
proof of purchase, postage prepaid, to Multinautic® at
2330, Jean-Adam, St-Sauveur, QC, Canada,
J 0 R 1 R 2 . Write the
RAN on the shipping label. Any product sent without RAN will
be refused and returned freight collect to sender.
This warranty is not transferable. This warranty does not
apply in cases of abuse or misuse of the product, use
contrary to Multinautic®'s instructions, an act of God,
negligent use, purchase from a party other than a
Multinautic® authorized reseller, unauthorized repair,
or modification of the product.
ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED TO
THE EXTENT PERMITTED UNDER APPLICABLE LAWS AND, TO
THE EXTENT NOT PERMITTED, ARE HEREBY LIMITED TO THE
DURATION AND TERMS OF THIS WARRANTY. MULTINAUTIC®
ALSO HEREBY DISCLAIMS ALL LIABILITY FOR INCIDENTAL,
SPECIAL, OR CONSEQUENTIAL DAMAGES.
Some provinces do not allow limitations on how long an
implied warranty lasts, or the exclusion or limitation of
incidental or consequential damages, so the above limitation
may not apply to you. This warranty gives you specific legal
rights, and you may have other rights which vary from state
to state or province to province. This warranty does not
restrict the rights of the consumer mandated under applica-
ble laws. THIS WARRANTY SUPERSEDES ALL OTHER
WARRANTIES THAT ARE ASSOCIATED WITH THIS PRODUCT.
Multinautic®, property of Multi Online Distribution Inc.
2330, Jean-Adam, St-Sauveur, QC
Canada,
J 0 R 1 R 2
www.multinautic.com [email protected]
Should you encounter any difficulties with
this product, do not return it to the store.
Please contact our
customer service at
1-800-585-1237 toll-free
10522
22000
Wheel Kit
For easy dock-in and out.
Included:
2x plastic dock wheels –61 cm (24 in.)
2x wheel axles –26.7 cm (10 1/2 in.)
2x hitch pins
2x large flat washers
QP-400 Cedar Decking Kit
Red western cedar (cut to size) and the
screws needed to assemble one
Multinautic®QP-400 dock section.
21175
Printed in Vietnam
Look online for our
Kayak Racks and
Paddle-board Support Kits !
HDG Steel Posts (1-11/16 in. O.D.)
Some layouts may require the addition
of a post or more.
For a higher installation of your dock,
use longer piles according to your needs.
To secure it to the shore, choose shorter
ones.
Complete kits with base plates and caps
are also available.
11007 0.91 m (3 ft)
11006 1.22 m (4 ft)
10009 1.83 m (6 ft)
11005 2.44 m (8 ft)