MULTIQUIP GA36HR User manual

GA SERIES PORTABLE GENERATORS — WHEEL KIT INSTRUCTIONS — REV. #0 (04/08/14) — PAGE 1
GA Series Portable Generators
Wheel Kit Instructions for GA36HR, GA6HR and GA6HRS
The following instructions are intended to assist the user in the installation of the Wheel Kit. Please read all assembly
instructions before installing the kit.
REQUIRED TOOLS
1/4" Drive Ratchet with Socket Set
Snap Ring Tool
PARTS
Verify that all parts are accounted for. See Table 1 below
and Figure 1 on page 3.
Table 1. GA Series Generator Wheel Kit
Item
No. Part No. Description QTY. Item No Part No Description QTY.
1 A3417400303 Axle, Transport Wheel 1 10 A3417400804 Handle, LS 1
2 A3417400404 Bracket, Axle Frame 2 11 W0805003103 Rubber Hand Grip 2
3 L0120236304A Bracket, Mounting Axle 4 12 0016908020 Bolt, M8X20 With Flat/Lock Washers 16
4 Y0605802053 Wheel 2 13 0016906015 Bolt, M6X15 With Flat Lock Washers 8
5 Y0080000020 Snap Ring 2 14 0010108025 Bolt, M8X25 2
6 A3417400904 Support Stand 2 15 0207608000 Nut, M8 2
7 A3417401304 Bracket, Handle RS 1 16 0041208000 Washer, Flat M8 2
8 A3417401404 Bracket, Handle LS 1 17 0601851116 Washer, Plastic 4
9 A3417400704 Handle, RS 1 18 0012308020 Bolt, M8X20 With Flat/Lock Washers 6
WORK SAFELY!
Follow all shop safety rules when performing this installation.
Make sure work area is clean and free of debris.

GA SERIES PORTABLE GENERATORS — WHEEL KIT INSTRUCTIONS — REV. #0 (04/08/14) — PAGE 2
PROCEDURE
Reference Figure 1 for all instructions.
Wheel/Axle Installation (Step 1)
1. Place generator on secure level ground where it will
not slip or slide.
2. Using four M8X20 bolts (item 12), that includes a lock
washer and flat washer, attach axle frame brackets
(item 2) to the bottom right and left sides of the pipe
frame. Tighten securely.
3. Place the four axle mounting brackets (item 3) onto
axle (item 1).
4. Next, using eight M8X20 bolts (item 12), that includes
a lock washer and flat washer secure the four axle
mounting brackets (item 3) to the left and right side
axle frame brackets (item 2).Tighten securely.
5. Place wheels (item 4) onto axle and secure wheels to
axle with with snap ring (item 5).
Stand Installation (Step 2)
1. Using eight M6X15 bolts (item 13), that includes a
lock washer and flat washer, attach support stands
(item 6) to pipe frame. Tighten securely.
Handle Installation (Step 3)
1. Using two M8X20 bolts (item 18), that includes a
lock washer and flat washer attach left-side handle
bracket (item 8) to pipe frame. Tighten securely.
2. Lubricate (grease) free end of left-side handle
(item 10) and slide rubber hand grip (item 11) onto
handle.
3. Using a M8X25 bolt (item 14), M8 flat washer
(item 16), two plastic washers (item 17) and flanged
lock nut (item 15), attach left-side handle (item 10) to
left-side handle bracket (item 8). Do not over tighten.
4. Repeat for right-side handle (item 9).

GA SERIES PORTABLE GENERATORS — WHEEL KIT INSTRUCTIONS — REV. #0 (04/08/14) — PAGE 3
STEP 1
STEP 2
STEP 3
17
17
14
8
15
10
11
5
5
4
4
12
33
12
3
1
6
16
2
3
9
7
18
13
13
Figure 1. Wheel Kit Assembly

GA Series Portable Generators
Wheel Kit Instructions for GA36HR, GA6HR and GA6HRS
Your Local Dealer is:
HERE’S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
United StateS
Multiquip Corporate Office MQ Parts Department
18910 Wilmington Ave.
Carson, CA 90746
Contact: [e-mail]
Tel. [phone]
Fax [phone]
800-427-1244
310-537-3700
Fax: [phone]
Fax: [phone]
Service Department Warranty Department
800-421-1244
310-537-3700
Fax: [phone]
310-537-3700
Fax: [phone]
Technical Assistance
800-478-1244 Fax: [phone]
Canada United Kingdom
Multiquip Multiquip (UK) Limited Head Office
4110 Industriel Boul.
Laval, Quebec, Canada H7L 6V3
Contact: [e-mail]
Tel: [phone]
Tel: [phone]
Fax: [phone]
Unit 2, Northpoint Industrial Estate,
Globe Lane,
Dukinfield, Cheshire SK16 4UJ
Contact: [e-mail]
Tel: [phone]
Fax: [phone]
© COPYRIGHT 2014, MULTIQUIP INC.
Multiquip Inc
, the MQ logo and the Whiteman logo
are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other
trademarks are the property of their respective owners and used with permission.
This manual
MUST accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations, descriptions, references and technical data contained in
this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change specifications, design or the information published
in this publication at any time without notice and without incurring any obligations.